Pima HUNTER-PRO 896 User manual

HUNTER-PRO 896 Ver. 2.0.2
9-96 Zones Intruder Alarm System
USER GUIDE

2 HUNTER-PRO 896 - User Guide
PIMA Electronic Systems Ltd. does not represent that its Product may not be compromised
and/or circumvented, or that the Product will prevent any death, personal and/or bodily
injury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that
the Product will in all cases provide adequate warning or protection. The User understands
that a properly installed and maintained equipment may only reduce the risk of events such
as burglary, robbery, and fire without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no death, personal damage and/or damage to
property as a result.
PIMA Electronic Systems Ltd. shall have no liability for any death, personal and/or
bodily injury and/or damage to property or other loss whether direct, indirect,
incidental, consequential or otherwise, based on a claim that the Product failed to
function.
Please refer to a separate warranty statement found on PIMA website at:
http://www.pima.co.il/site/Content/t1.asp?pid=472&sid=57
Warning: The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environment conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user is
advised to take all necessary precautions for his/her safety and the protection of his/her
property.
This document may not be duplicated, circulated, altered, modified, translated, reduced to
any form or otherwise changed, unless PIMA’s prior written consent is granted.
All efforts have been made to ensure that the content of this manual is accurate. Pima
retains the right to modify this manual or any part thereof, from time to time, without
serving any prior notice of such modification.
Please read this manual in its entirety before attempting to program or operate your system.
Should you misunderstand any part of this manual, please contact the supplier or installer of
this system.
Copyright ©2007-8 PIMA Electronic Systems Ltd. All rights reserved.
Contact us:
PIMA Electronic Systems Ltd.
5 Hatzoref Street, Holon 58856, Israel
Tel: Sales: [phone] Support: [phone]
Fax: [phone]
Email: [e-mail]
Web: http://www.pima-alarms.com

HUNTER-PRO 896 - User Guide 3
TABLE OF CONTENTS
CHAPTER 1 Introduction ...................................................................................5
1.1 Main Features............................................................................................................................. 6
1.2 Signs, Programming Keys and Codes.................................................................................... 6
1.3 Entering User Menu.................................................................................................................. 7
CHAPTER 2 The Keypad ....................................................................................8
2.1 Display Types............................................................................................................................. 8
2.2 Keys Functions.........................................................................................................................10
CHAPTER 3 Arming & Disarming.................................................................. 12
3.1 Normal Arming & Disarming By the Keypad....................................................................12
3.2 Arming When One or More Zones are Opened............................................................12
3.3 Arming with Master Code ....................................................................................................13
3.4 Arming with User or Short Codes .....................................................................................13
3.5 Arming the System to HOME 1/HOME 2 Modes ...........................................................13
3.6 Fast Arming ..............................................................................................................................13
3.7 Arming Using Enabled User Code ......................................................................................13
3.8 Arming with Key, Key fob, or Proximity Tag ...................................................................14
3.9 Automatic Arming ..................................................................................................................14
3.10 Disarming..................................................................................................................................15
CHAPTER 4 Remote Control Via Phone..................................................... 16
4.1 Mode A: Basic Operations....................................................................................................16
4.2 Mode B: Full functions............................................................................................................17
CHAPTER 5 Memory Log ................................................................................ 19
5.1 Accessing Memory Log..........................................................................................................19
5.2 Memory Log Display ..............................................................................................................19
CHAPTER 6 Zones Bypassing ......................................................................... 20
CHAPTER 7 Display Types.............................................................................. 21
7.1 Zone Status Display................................................................................................................21
7.2 Display type screens by order .............................................................................................21
7.3 Examples of display types......................................................................................................22
CHAPTER 8 Phone Numbers & SMS Messages.......................................... 24
8.1 Edit Dialer Phone Numbers .................................................................................................24
8.2 SMS Options.............................................................................................................................24
8.3 Dialer Test................................................................................................................................25
CHAPTER 9 Time and Date............................................................................ 26
CHAPTER 10 Codes....................................................................................... 27
10.1 Master Code ............................................................................................................................27
10.2 User Code................................................................................................................................27
10.3 Entering Names and Characters..........................................................................................29
10.4 Entering a User Name ...........................................................................................................30
10.5 User Parameters .....................................................................................................................30
10.6 Disarming Time Window......................................................................................................30
10.7 User’s Partitions......................................................................................................................31
10.8 Allocating a Key fob to a User.............................................................................................31

4 HUNTER-PRO 896 - User Guide
10.9 Deleting a Key fob ..................................................................................................................32
10.10 Proximity TAG ........................................................................................................................32
10.11 Duress Code............................................................................................................................33
10.12 Short Code...............................................................................................................................33
10.13 Door Code...............................................................................................................................33
CHAPTER 11 Other Topics.......................................................................... 34
11.1 Chime ........................................................................................................................................34
11.2 Panic Signal................................................................................................................................34
11.3 Resetting Smoke/Fire/Anti-Mask Detectors .....................................................................34
11.4 System Tests ............................................................................................................................35
11.5 Turning Off the Keypad Buzzer...........................................................................................35
CHAPTER 12 Troubleshooting.................................................................... 36
Appendix: Zones Table ............................................................................... 38

HUNTER-PRO 896 - User Guide 5
CHAPTER 1 INTRODUCTION
Congratulations on your purchase of the HUNTER-PRO 896 Intruder Alarm System!
Much care has been taken in developing the HUNTER-PRO 896 Intruder alarm
system, to provide you with unprecedented peace of mind. The user-friendly
system with its advanced features will professionally help you to protect your home
or business.
HUNTER-PRO 896 contains numerous features that allow it to befit the customer’s
individual needs, and yet remain easy to program and use both by the customer
and the technician. Therefore, it is important to read this manual thoroughly in
order to familiarize yourself with the system and take full advantage of its features.
To assure optimal safety and security, you should perform a system test to the
HUNTER-PRO 896 once a week at least (see instructions further on this guide).
For any further questions, please contact your local PIMA distributor or PIMA
directly according to the ‘contact us’ details on page 2.
Up to date literature is available to download from our website at:
www.pima-alarms.com
SAFETY INSTRUCTIONS
Your HUNTER-PRO 896 alarm system has been registered in accordance with EN60950 and its rules.
EN 60950 requires us to advise you the following information:
1. In this alarm system exist hazards of fire and electric shock. To reduce the risk of fire or electric
shock, do not expose this alarm system to rain or moisture. Pay attention: Telephone cords could be a
good conductor for lightings energy.
2. Do not open the door of the alarm system. Dangerous high voltages are present inside of the
enclosure. Refer servicing to qualified personnel only.
3. This alarm system should be used with AC 230V50Hz, protected by anti electric shock breaker. To
prevent electric shocks and fire hazards, do NOT use any other power source.
4. Do not spill liquid of any kind onto the unit. If liquid is accidentally spilled onto the unit,
immediately consult a qualified service.
5. Install this product in a protected location where no one can trip over any line or power cord. Protect
cords from damage or abrasion.
6. Disconnect all sources of power supply before proceeding with the installation. Pay attention: do not
install low voltage wires near by AC power wires they should be separated.
7. Connect the AC transformer output to the terminal block on the control panel as marked.
8. Connect the AC line cord to line power terminals as marked. (GND; N; L)

6 HUNTER-PRO 896 - User Guide
1.1 Main Features
Hybrid system with 8 to 96 wired or wireless zones
Friendly and easy to use and program, with fast arming keys
LCD keypad with multilingual Menu-Driven screens for easy programming and
operation
Wide partitioning options:
oUp to 16 partitions, each with its own Account ID and Users
oUp to 8 subsystems, each with different keypads, IDs, etc.
Passive arming: after a preset silence (no movement) time
Automatic arming: at a preset time
Full remote control including outputs via touch-tone telephone
Control codes: 96 user codes, 96 proximity tag codes, 24 remote control
codes, master code, door code, duress code
Various authorization levels for each user
Window time to restrict users from disarming the system (by code entering or
remote control)
Extensive zone testing
3 display types to view system status: “PIMA Fast display”, “Scan Open Zones”
and “All Zones Status”.
Built-in Unique Integrated Digital 4 channels to communicate with the CMS
(Central Monitoring Station): Telephone, Long-range Radio, GSM, GPRS
Full supervision data of wireless detectors (life signal, low battery, tamper)
4 Subscriber dialing numbers with optional voice message/microphone
Various methods for preventing false alarms: Zone conditioning, pulse counter,
2 EOL resistors to detect short & cut, zone sensitivity, automatic zone
deactivating, zone soaking
Various accessories (microphone, voice unit etc.)
Memory Log of up to 500 events (250 are non-volatile) that includes Time,
Username and Zone name.
1.2 Signs, Programming Keys and Codes
Press a key
Press a key until confirmation beep sounds
Moves the cursor forward
Moves the cursor backwards
Enter the next level / Save

HUNTER-PRO 896 - User Guide 7
Enable (‘+’) or disable (‘-‘) a parameter / Clear the display
Go up one level / Go to main display / Cancel
Master Code:A code enabled to enter the User menu.
User Code: A code enabled by Master Code to enter the User menu.
Printed Zone Numbers: On the LCD keypad, zones number 1-16 and 17-32 are
printed above and below the display window.
1.3 Entering User Menu
The User menu is where the user program and change data. User menu can be
fully accessed with the Master Code. Other users can also access the User menu
but are limited according to their authorization level, programmed by the system
administrator (owner)/technician (see “Programming Codes” on page 27).
1.3.1 Entering User Menu with Master Code
Master Code User Menu
Choose 1,2... Function key (see page 9)
1.3.2 Entering User Menu with User Code
If a user is enabled by technician to enter the User Manu:
User Code User Menu
Choose 1,2...
Function key (see page 9)
If a user is not enabled by technician to enter the User Menu (User Code
arms/disarms the system), the menu can still be accessed as follows:
User Code User Menu
Choose 1,2...
Function key (see page 9)
When a user selects a function (i.e., the corresponding key is pressed) it is not
authorized to, the system displays the following:
Access Denied!
Press END


8 HUNTER-PRO 896 - User Guide
CHAPTER 2 THE KEYPAD
RXN-400 and RXN-41O are PIMA’s LCD keypads that operate with
HUNTER-PRO 896. They have been specially designed for maximum simplicity and
durability and present decorative design. A keypad is used for arming, disarming
and programming the system as well as displaying time and date, system status
information, events and faults, memory log and more.
Printed on the keypad above each num key is the key function. For instance, key
#9 is the codes programming key, key #2 is the memory log key and so on. A full
description of each key function appears further on this guide.
Both RXN-400 and RXN-41O keypad models are identical, except for their screen
size.
The display screen has two lines with 16 characters each. The upper line displays
the time and the date (depending on the display type). Both lines display data
regarding the system, such as events, faults and zone status.
Note: Up to 8 monitored keypads can be connected to the system simultaneously
Drawing 1- PIMA’s RXN-410 LCD keypad with PIMA Display
2.1 Display Types
2.1.1 PIMA Fast Display
This display is best used on a 32 zones system. All events and zones are displayed
in a single screen using signs and abbreviations. Drawing 1 demonstrates PIMA fast
display (with 16 zones).
Information on the top line includes: time, date and system status. If the system is
configured to more than 16 zones than this information will not be presented in this
display type, but zones information only (see next drawing).

HUNTER-PRO 896 - User Guide 9
System status characters on top line:
PSystem is communicating or testing the PSTN line
SSiren ON
RRelay ON
TSystem is reporting to Monitoring Station via radio transmitter
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
C ------__ _ _ _ ----
- B_ --FA-_ --V-SS-
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Zone Status and Events
1-32 Zone
numbers
engraved
on the
keypad
Zone Status and Events
Drawing 2 - Fast Display, 32 zones
The following signs & characters appear next to the zone number/ partition that is
engraved on the keypad:
-Closed zone
_Opened zone
BBypassed zone
AAlarm zone (zone triggering an alarm)
CChime zone
SShortcut zone (zone was shortcut)
FFailed zone (disconnected)/Tamper event (in a wireless detector)
LLow battery in wireless detector
VSupervision signal: Wireless detector did nor report test to system
TZone is in Soak test
Note: When in PIMA display, the system will not display the zone status during
faults. Only after all faults are resolved, PIMA Display returns.
2.1.2 ‘Scan Open Zones’ Scrolling Display
In this display type the zones and events screens automatically interchange and
display their status in a chronological order.
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
5 J UN 07 PS00:22
V o l tage
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Event/Fault
System status
The upper line display is described in sub-section 2.1.1.

10 HUNTER-PRO 896 - User Guide
Bottom line display:
Events, alerts and faults
Opened zones (OP)
Zones that triggered an alarm (AL)
2.1.3 Other Display Types
Display Type What is displayed?
Disable zones Open zones are not displayed
All Zones All zones are displayed with their number and name, as
programmed by the technician
Bypassed Zones All bypassed zones are displayed
Soak Zones All soaked (tested) zones are displayed
Chime Zones All chimed zones are displayed
All Zones Status See next sub-section (2.1.4)
Partitions Names See sub-section (2.1.5)
2.1.4 All Zones Status Display
NEXTNEXT
.…
C--___BB-- 1->10
-F--S_---- 11->20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
--------- 21->30
--------- 31->40
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
--------- 81->90
------ 91->96
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Zone number
All programmed zones in the system are displayed, 10 zones in each line, 20 in
every screen. In the above drawing, the first screen shows zones 1 - 10 and
11 - 20. Advance by pressing , return by pressing .
“All zones status” display differs from “PIMA fast display”, by showing all 96 zones
in the system (if all programmed), while “PIMA fast display” shows only the first 32
zones in one screen.
2.1.5 Partitions Names Display
All partitions (if programmed any) will be displayed with their name.
Note: When in PIMA fast display mode, the system will not show zones’ status if a
fault occurs. Only when the fault is resolved the fast display returns.
2.2 Keys Functions
As mentioned previously, operating and programming the system commences by
entering the Master Code first and then pressing any further required key.
However, a number of keys enable certain actions by a single long press, without
entering Master Code. The next table lists the various options:

HUNTER-PRO 896 - User Guide 11
Key Enter Master/ User Code and
press a key to..
Long press a key (without
entering Master/User Code) to...
Arm/Disarm Fast arming the system∗
Display arming, alarm and fault
history with time and date -
Temporary bypass of zones -
Arm the system to “Home 1”
partial arming mode
Fast arming the system to “Home 1”
partial arming mode*
Display menu (see “Display
Types”, page 5) “All Zones” display
Program telephone numbers -
Arm the system to “Home 2”
partial arming mode
Fast arming the system to “Home 2”
partial arming mode*
Program Time and date -
Program User codes -
Program Chime by zone Enable/Disable Chime for all zones
Program Auto-arming Enter user menu with enabled code
- - Display armed partitions
- Reset smoke detectors
(Programming help key) Turn off buzzer in fault
Display system name and
version; Enter technician menu Display Service Provider
Test siren, battery, AC and
phone line -
(Programming help key) Display system’s Name & Version
∗If enabled by technician

12 HUNTER-PRO 896 - User Guide
CHAPTER 3 ARMING &DISARMING
Note: The system’s default Master Code is 5555
The system can be armed and disarmed in 4 ways:
With the Keypad
By remote control or Key fob
Automatically (arming only)
Remotely, via touchtone telephone, COMAX software, Internet, and GSM
As a rule, the system should be armed only when all zones (but those on the exit
route) are closed and there are no faults (e.g., low battery, mains) and/or events
(e.g., fire, panic). To arm the system with open zones, these zones should first be
bypassed, as explained in this chapter.
3.1 Normal Arming & Disarming By the Keypad
Before arming the system, make sure all zones (except exit delayed zones – usually
zones on exit route) are closed: no _open zone blinking sign should be displayed
(all zones indication is _). In scrolling display, the next ‘OP:’ sign should not
appear:
14 SEP 07 09:55
OP:ZONE 15
To arm the system: User Code/Short Code. The green LED shall begin to blink,
beeps will be heard from the keypad and the display will show the next exit delay
message:
Arming...
Exit Delay 60
At the end of the exit delay, the green control LED shall stop to blink and stay on,
the beeps will stop, the display will briefly show the following message:
System Armed!
and the display will look like this:
14 SEP 07 09:56
3.2 Arming When One or More Zones are Opened
When trying to activate the system with one or more zones opened (that are not on
the exit route, i.e., exit delayed zones), the keypad will produce a fast-beep and the
display will show the next (i.e.) scrolling screens:
Open Zone! Press
OP:Front door
Bypass or END
OP:Front door
...
. The bottom line shows the names
and numbers of all opened zones, one by one. If no step is taken the system will be
armed and alarms will be generated from the open zones.
Master Code / User Code 

HUNTER-PRO 896 - User Guide 13
These are the two possible ways to act:
1. To temporary bypass the open zones:. Open zones are bypassed &
system is armed. The letter Bwill appear next to the corresponding zone/s.
2. To cancel arming:. The system returns to normal operation mode.
3.3 Arming with Master Code
Master Code
User Menu
Choose 1,2... 
Arming...
Exit Delay 60 ….
System Armed!
3.4 Arming with User or Short Codes
Short Code or User Code
Arming...
Exit Delay 60 ….
System Armed!
3.5 Arming the System to HOME 1/HOME 2 Modes
‘HOME 1’ and ‘HOME 2’ are partial zones arming modes.
Arming to “HOME 1”
: Short Code / User Code or
Master Code 
Home 1 Arming..
Exit Delay 60
Arming to “HOME 2” : Short Code / User Code or
Master Code 
Home 2 Arming..
Exit Delay 60
3.6 Fast Arming
To quickly arm the system, if enabled by technician:
Full Arming: 
Arming...
Exit Delay 60 ….
System Armed!
Arming to ‘HOME 1’: 
Home 1 Arming..
Exit Delay 60 ….
System Armed!
Arming to ‘HOME 2’: 
Home 2 Arming..
Exit Delay 60 ….
System Armed!
Note: ‘HOME 1’ and ‘HOME 2’ exit delays can be disabled by a technician.
3.7 Arming Using Enabled User Code
If a user was enabled by technician to enter the User Manu:
User Code User Menu
Choose 1,2...


14 HUNTER-PRO 896 - User Guide
If a user is not enabled to enter the User Menu:
User Code User Menu
Choose 1,2...

3.8 Arming with Key, Key fob, or Proximity Tag
A key, 24 Key fobs and 96 RFID proximity tags can be attached to HUNTER-PRO
896. The Visonic Key fob has 4 push buttons for: Arming, Disarming, Arming to
‘Home 1’ and controlling one of the system’s outputs. Pushing simultaneously “Full
Arming” and “Home 1” buttons generates Panic alert.
The Key fob works with
PIMA’s I/O-WN wireless
receiver and enables arming,
disarming, duress alert,
system output control and
arming to ‘HOME 1’.
3.9 Automatic Arming
HUNTER-PRO 896 offers two ways to arm the system automatically:
1. Active - At a preset time, daily.
2. Passive - Arming when no activity is sensed by any detector for a period of time.
Passive arming can be programmed per partitions.
3.9.1 Automatic arming at a preset day and hour
This feature lets you program the system to automatically arm itself in any day of
the week at a specified hour. At the designated hour, the LCD keypad displays
Auto Arming - 45
Xand a countdown of 45 seconds starts. The countdown comes
together with chime sound from the keypad. After the countdown is over, the
arming process starts, according to the system’s programming:
Arming...
Exit Delay 60 ….
System Armed!
.
At any time during the countdown, entering a valid code stops the automatic
arming process.
Master Code / User Code or + User Code User Menu
Choose 1,2...
Auto Arm By Day
ENTER/NEXT/END Auto Arm By Day
Sunday 00:00 Set the time in which auto
arming process starts or to set another day. to save.
Leaving the default 00:00 hour (or setting to it) means auto arming is disabled.

HUNTER-PRO 896 - User Guide 15
Note: To cancel a preset auto arming time, repeat the process and program it to
00:00 hour.
3.9.2 Automatic arming when no activity is sensed
Set inactivity time (in minutes) - a period of time in which if no activity is sensed by
any detector the system will automatically be armed.
Master Code / User Code OR + User Code User Menu
Choose 1,2...
InactivityToArm
ENTER/NEXT/END InactivityToArm 5 Minutes set inactivity
time in minutes Inact Per part
+++++++++++++++++ Mark ‘+’ to enable the partition/s to
be auto armed
Note: “Inactivity to arm” timing is programmed by the technician.
3.10 Disarming
3.10.1 With Master Code
Master Code 
Disarming..
3.10.2 With User Code
User Code or + User Code
Entering user code immediately disarms the system.
Note: If the system is not disarmed, make sure you are not trying to disarm it
outside the time frame you are enabled to (see “Programming User Codes” on
page 27)
3.10.3 With Duress Code
Entering duress code disarms the system but also sends alert to the CMS and the
private dialer. Duress code is a disarming code only.
Duress Code
Disarming..

16 HUNTER-PRO 896 - User Guide
CHAPTER 4 REMOTE CONTROL VIA PHONE
The alarm system can be remotely controlled via any touch tone or cellular phone.
There are two modes of remote control: basic operations, mostly arming and
disarming; And full operations, including activating outputs.
4.1 Mode A: Basic Operations
1. Dial to the system’s telephone number.
2. Wait for the system’s confirmation tone (a long tone followed by 2 beeps).
Once a connection was established, any operation can take place, whether
you dialed to the system or vice versa.
3. Enter Master Code. Do not to enter the code before the confirmation tone
ends.
4. Wait a few seconds until the system confirms its status by one of the two
following tones:
Continuous tone: The system is disarmed
Beep: The system is armed
Note: The system will not recognize commands (tones) from the telephone while
sounding the confirmation tone. It is important to wait until the confirmation tone
is over before pressing the telephone keys that control the system.
5. Execute a command by pressing a key on the phone:
Phone key Function
0 Disable siren and dialer. The dialer will stop dialing to the next private
phone numbers.
1 Arm the system
2 Disarm the system (if enabled by the technician)
4 Arm the system to “Home 1” mode
5 Switch on the Relay
6 Switch off the Relay
7 Arm the system to “Home 2” mode
8 Listen in for one minute (available only with MIC-200). Any more presses
will extend the listen in time in one minute
Notes:
1) The alarm system confirms the command was received by 2 short beeps.
2) While the system and the telephone are communicating, the message “Other
keypad in use” will display on all connected keypads. If the system does not
receive any command for a period of 60 seconds, it shall disconnect and return
to regular operation mode. The system will remain in standby (with the above
displayed on keypads) for another 60 seconds before keypad operation
returns.

HUNTER-PRO 896 - User Guide 17
4.2 Mode B: Full functions
Note: By default, the system is set to mode A. Switching to mode B requires
technician programming.
1. Follow steps 1 - 4 in section 4.1 to establish communication with the system.
2. To trip an output:& the corresponding numbers from the following
table.
3. To release an output:& the corresponding numbers from the following
table:
System Panel outputs OUT-1000 Expander
*01 Arm 11 External siren 21 Output # 1
#01 Disarm 12 Internal siren 22 Output # 2
*04 Home 1 13 Relay 23 Output # 3
*07 Home 2 14 Reset smoke
detectors
24 Output # 4
*08 Listen in (with MIC-
200)
15 ON/OFF output 25 Output #5
*00 Stop sirens and dialer 16 ALARM output 26 Output # 6
17 Audio Ctrl output 27 Output # 7
28 Output # 8
I/O-8Ns Relays
31 Expander # 1 37 Expander # 7
32 Expander # 2 38 Expander # 8
33 Expander # 3 39 Expander # 9
34 Expander # 4 40 Expander # 10
35 Expander # 5 41 Expander # 11
36 Expander # 6
I/O-R Expander #1 I/O-R Expander #2
51 Output #1 55 Output #5 59 Output #1 63 Output #5
52 Output #2 56 Output #6 60 Output #2 64 Output #6
53 Output #3 57 Output #7 61 Output #3 65 Output #7
54 Output #4 58 Output #8 62 Output #4 66 Output #8
I/O-R Expander 33 I/O-R Expander #4
67 Output #1 71 Output #5 75 Output #1 79 Output #5
68 Output #2 72 Output #6 76 Output #2 80 Output #6
69 Output #3 73 Output #7 77 Output #3 81 Output #7
70 Output #4 74 Output #8 78 Output #4 82 Output #8
Sending system status via SMS message
to the private dialer
91 Phone #1 93 Phone #3
92 Phone #2 94 Phone #4

18 HUNTER-PRO 896 - User Guide
4.2.1 Examples for mode B
Deactivating external siren:
Dial and wait for confirmation tone. When no sound heard Master Code and
wait for confirmation tone 11 (on telephone keys).
Activate output #5 on OUT-1000 outputs card:
Dial and wait for confirmation tone. When no sound heard Master Code and
wait for confirmation tone25 (on telephone keys).

HUNTER-PRO 896 - User Guide 19
CHAPTER 5 MEMORY LOG
The system holds in its memory the last 500 events and operations in a chronological
order. 250 of them are non-volatile.
5.1 Accessing Memory Log
Master Code / User Code or User Code
User Menu
Choose 1,2...  
1) 10 AUG 19:44
Zone Bypassed 6 .
5.2 Memory Log Display
The system’s memory log has 4 sub-menus/viewing options:
All Events, Faults Only, Zone Alarms, Arming/Disarming.
The log is displayed in 2 lines:
The top line displays the event’s no. and time and date it occurred.
The bottom line displays the event type and the zone it occurred in and any
other events.
The information/events logged in the memory are: arming, disarming, alarms, code
changed, system time changed, faults, zones bypassed and more.
Examples:
Burglary alarm:
2)1 SEP 08 21:20
Burgl ALARM 4
Event Numbe
r
Zone Number
Event
Zone type
E ven t D a te & Tim e
…….
2)1 SEP 08 21:20
Kitchen
Zone name
Two screens are displayed intermittently, showing the zone’s name:
Fault:
56)4 MAR 08 02:54
AC Fault

20 HUNTER-PRO 896 - User Guide
CHAPTER 6 ZONES BYPASSING
If a zone is opened, the system cannot be armed, unless the zone is either closed
or bypassed. A bypassed zone will automatically become active again the next time
the system is disarmed.
Master Code / User Code or User Code User Menu
Choose 1,2...

Zone Number: 1
Entr-Conf #-Rst 
Bypassed Zone
Rear Window -1
Zone name & number . 
to confirm and to scroll to the next zone. The letter “B” indicates a bypassed zone.
To reset a bypassed zone .
Note: If a zone is bypassed and the system is not armed within a period of time
set by the technician, the zone becomes active again.