Pima hunter-pro User manual

Intruder Alarm System
HUNTER-PRO (Ver. 2.8)
Installation Manual
PIMA Electronic Systems Ltd.
5 Hatzoref Street, Holon 58856, Israel
℡ [phone]  [phone]
{ [email protected] + http://www.pima-alarms.com

Hunter-Pro Installation Manual
2
PIMA Electronic Systems Ltd. Is not liable for any compromised and/or
circumvented product, or that the product will prevent death, personal and/or
bodily injury and/or damage to property resulting from burglary, robbery, fire
or otherwise, or that the Product will in all cases provide adequate warning or
protection. The User understands that a properly installed and maintained
equipment may only reduce the risk of events such as burglary, robbery, and
fire without warning, but it is not insurance or a guarantee that such will not
occur or that there will be no death, personal damage and/or damage to
property as a result.
PIMA Electronic Systems Ltd. shall have no liability for any death, personal
and/or bodily injury and/or damage to property or other loss whether direct,
indirect, incidental, consequential or otherwise, based on a claim that the
Product failed to function.
Warning: The user should follow the installation and operation instructions
and among other things test the Product and the whole system at least once a
week. For various reasons, including, but not limited to, changes in
environment conditions, electric or electronic disruptions and tampering, the
Product may not perform as expected. The user is advised to take all
necessary precautions for his/her safety and the protection of his/her property.
This document may not be duplicated, circulated, altered, modified,
translated, reduced to any form or otherwise changed; unless PIMA’s prior
written consent is granted.
All efforts have been made to ensure that the content of this manual is
accurate. Pima retains the right to modify this manual or any part thereof,
from time to time, without serving any prior notice of such modification.
Please read this manual in its entirety before attempting to program or operate
your system. Should you misunderstand any part of this manual, please
contact the supplier or installer of this system.
Copyright  2004 by PIMA Electronic Systems Ltd. All rights reserved.
You can contact us at:
PIMA Electronic Systems Ltd.
5 Hatzoref Street, Holon 58856, Israel
http://www.pima-alarms.com

Hunter-Pro Installation Manual
3
The
HUNTER-PRO includes many sophisticated features that allow you to custom tailor it to
your individual needs, and yet remain easy to operate and program for both the user and
installer.
This manual contains technical as well as end user instructions. Also available is a User
Manual dedicated for the end user.
IMPORTANT!
Please refer to the HUNTER-PRO User Manual for a better in depth understanding of end user
features and functions.
This installation manual contains technical and programming instructions for a quick and
simple installation and maintenance of the system.
If, despite this detailed manual, questions remain or something is unclear, do not hesitate to
contact your local
PIMA distributor or PIMA directly at:
PIMA Electronic Systems Ltd.
Tel.: [phone]
Fax: [phone]
Email: [email protected]
Up to date literature is available to download from our website:
www.pima-alarms.com
Introduction

Hunter-Pro Installation Manual
4
Safety Instructions
Your HUNTER-PRO alarm system has been registered with the CE (complying with EN
60950 standart). Accordingly, this section is designed to assist you in identifying
potentially unsafe conditions while operating our product:
 To reduce the risk of fire or electric shock, do not expose this alarm system to rain or
moisture.
 Do not open the door of the alarm system. Dangerous high voltages are present inside
of the enclosure. Refer servicing to qualified personnel only.
 This alarm system should be used with AC 230V, 50Hz. To prevent electric shocks and
fire hazards, do NOT use any other power source.
 Do not spill liquid of any kind onto the unit. If liquid is accidentally spilled onto the
unit, immediately consult a qualified service.
 Install this product in a protected location where no one can trip over any line or
power cored. Protect cords from damage or abrasion.
 Disconnect all sources of power supply before proceeding with the installation.
 Connect the AC transformer output wires to the terminal block on the Control Panel as
marked.

Hunter-Pro Installation Manual
5
Table of Contents
Introduction ............................................................................................................................................ 3
Safety Instructions ................................................................................................................................... 4
Chapter 1 The HUNTER-PRO Panel ..................................................................................................... 7
1.1 F USES ON THE C ONTROL P ANEL ..................................................................................7
1.1.1 Regular fuses.......................................................................................... 7
1.1.2 Thermal fuses......................................................................................... 7
1.2 C ONNECTIONS AND T ERMINALS ..................................................................................8
Chapter 2 Installing Peripherals ..........................................................................................................11
2.1 G ENERAL ................................................................................................................11
2.2 Z ONE I NPUTS ..........................................................................................................12
2.2.1 Connection without EOL resistor.......................................................... 12
2.2.2 Connection with one EOL resistor ........................................................ 13
2.2.3 Connection with two EOL resistors....................................................... 14
2.3 A RMING WITH K EY /R EMOTE C ONTROL ......................................................................15
2.4 TMPR1 AND TMPR2 ..............................................................................................15
2.5 S IRENS ....................................................................................................................16
2.6 R ELAY .....................................................................................................................16
2.7 ALARM AND ON/OFF............................................................................................17
2.8 K EYPADS .................................................................................................................17
2.9 T ELEPHONE .............................................................................................................17
2.10 M ICROPHONE .........................................................................................................18
2.11 V OICE U NIT ............................................................................................................18
2.12 R ADIO T RANSMITTER TRV/TRU-100.........................................................................19
2.12.1 Connecting the Transmitter: ................................................................. 19
2.13 E XPANDERS .............................................................................................................20
2.13.1 Outputs:............................................................................................... 20
2.13.2 Input Zones:......................................................................................... 20
2.14 C ONNECTING RC-PRO............................................................................................21
2.14.1 Connecting with the HUNTER-PRO ..................................................... 21
2.15 C ONNECTING COMMAND 48................................................................................21
2.15.1 Programming COMMAND 48.............................................................. 22
2.16 B ATTERY .................................................................................................................22
2.17 M AINS V OLTAGE .....................................................................................................22
2.18 S ETTING THE SYSTEM ................................................................................................23
Chapter 3 Programming and Operation ............................................................................................. 25
3.1 I NTRODUCTION .......................................................................................................25
3.1.1 Local Uploading with PRG-22 ............................................................. 25
3.1.2 Local programming with PC and LCL-11A ............................................... 26
3.1.3 Remote Programming with COMAX Software (Upload/Download) ............ 26
3.1.4 Programming with a Keypad ................................................................... 26
3.2 P ROGRAMMING WITH AN LCD KEYPAD .....................................................................28
3.2.1 Zone Sensitivity.................................................................................... 29
3.2.2 Zone Characteristics and Responses..................................................... 29
3.2.3 Monitoring Station Parameters.............................................................. 33

Hunter-Pro Installation Manual
6
3.2.4 Telephone Line Characteristics............................................................. 37
3.2.5 Siren, Relay, and Auxiliary Outputs...................................................... 40
3.2.6 Automatic Test Events to Monitoring Stations ....................................... 43
3.2.7 System Configuration ........................................................................... 45
3.2.8 Responses to Failures and Events.......................................................... 51
3.2.9 Typing Zone Names............................................................................. 54
3.2.10 Radio Transmitter Test.......................................................................... 54
3.2.11 Partitioning .......................................................................................... 54
3.2.12 Exit and Entry delay times..................................................................... 56
3.2.13 General Parameters.............................................................................. 56
Chapter 4 Private Dialer and Communication to Monitoring Station ..................................................59
4.1 D IALER TO PRIVATE NUMBERS ....................................................................................59
4.2 T ELEPHONE COMMUNICATION WITH M ONITORING S TATION ................................................59
4.3 R ADIO COMMUNICATION TO M ONITORING S TATIONS ................................................60
Chapter 5 Troubleshooting ........................................................................................................... 61
5.1 A CCESSING THE S YSTEM WITHOUT M ASTER C ODE .......................................................61
5.2 F AILURE INDICATIONS ..............................................................................................62
5.3 T ROUBLESHOOTING .................................................................................................62
5.3.14 No Radio Transmission to Monitoring Station....................................... 65
5.3.15 System is not answering telephone calls............................................... 65
5.3.16 Automatic arming is not functioning..................................................... 65
5.3.17 Zone does not cause an alarm.............................................................. 65
Chapter 6 Expenders ........................................................................................................................... 67
6.1 O UTPUT E XPANSION C ARD OUT-1000 ....................................................................67
6.2 Z ONE E XPANSION C ARD EXP-PRO ...........................................................................68
6.3 Z ONE D OUBLING ....................................................................................................68
6.3.1 Zone Doubling Options ....................................................................... 70
Chapter 7 Keypads.............................................................................................................................. 73
7.1 LCD K EYPADS .........................................................................................................73
7.1.1 Display Description ............................................................................. 73
7.1.2 Zone Statues Description ..................................................................... 74
7.1.3 Key Functions ...................................................................................... 75
7.1.4 Accessing the RJ-11 Socket (in RX-400 keypad models, and up)........... 76
7.2 O UTDOOR A NTI -V ANDAL K EYPAD : RX-200 ..............................................................76
7.2.1 LED Description................................................................................... 77
7.2.2 Installing the RX-200............................................................................ 77
Chapter 8 Appendixes......................................................................................................................... 79
A PPENDIX A: E NTERING N AMES WITH KEYPADS .....................................................................79
A PPENDIX B: D EFAULT P ARAMETERS .....................................................................................80
B1- Zones ............................................................................................................ 80
B2- Zoning........................................................................................................... 81
B3- Codes ............................................................................................................ 81
B4- System Configuration, General Parameters .................................................... 82
B5- Telephones.................................................................................................... 82
B6- System Events Response ................................................................................ 83
B7- Line/Wireless Station Report Codes ............................................................... 83
A PPENDIX C: T ABLE OF F ORMAT C ODES ...............................................................................84
Pulse Formats....................................................................................................... 84
DTMF Formats ..................................................................................................... 85
A PPENDIX D: HUNTER-PRO Q UICK R EFERENCE G UIDE .......................................................86

Hunter-Pro Installation Manual
7
Chapter 1
The HUNTER-PRO Panel
The following is a general drawing of the Control Panel:
TMPR
2
TMPR
1
ON/
OFF
ALARM
KEYPAD
HUNTER
PRO
EXPANSION CARD
SERIAL
KEYPAD
TRANSMITTER
U3
Z1 Z2 Z3 Z4 -+Z5 Z6 Z7 Z8 -+KEY -S1 S2 C N.O N.C -
SIREN RELAY SMOKE -+INOUT
F 3.15A 250VAC
F 5A 250VAC
CA
F5
T1
1
2
33 34 5 6
2
7 8 9 910 911
12
13
14
14
16 151718
JP1 JP2 JP4
1
LINE SET AUD
CONT
IN OUT
JP5
F3
F1
F6
JP6
F4
F7
F2
U2
19
20
1
1.1 Fuses on the Control Panel
1.1.1 Regular fuses
 F5 (5 Amp) - protects the battery from a short on the PCB.
 F6 (3.15 Amp) - protects the AC from a short on the PCB.
1.1.2 Thermal fuses
 F1 – Detector power supply (750mA)
 F2, F3 – Siren1 and Siren2 (1.1A)
 F4 – Keypad power supply (750mA)
 F7 – Protection for long range radio transmitter (200 mA)

Hunter-Pro Installation Manual
8
1.2 Connections and Terminals
1) AC – Voltage Input
14VAC input supplied by the transformer.
2) Connections to Backup Battery
Two wires connect the backup battery to the PCB. The red wire connects to the positive
(+) contact of the battery and the black wire connects to the negative (–) contact of the
battery.
IMPORTANT!
Ensure correct connection of battery polarity! Switching the polarity will damage the PCB.
3) Z1–Z8 – Zone Inputs
Zone inputs can be connected to all types of detectors with dry contact outputs. All zones
can be connected with single or double end–of–line resistors for short/disconnect
monitoring. Zone doubling is possible by connecting a diode and resistor to each zone
input. (See 6.3)
NOTE:
You can add 8 additional wired zones in one of two ways: 1. Zone inputs Z9–Z16 on expansion card
EXP-PRO. 2. Zone Doubling
4) (+) – Power Supply for Detectors
Power supply for detectors that require DC operating voltage
5) KEY – Key or Remote Arming Input
Connection to a momentary or fixed position key to arm/disarm the system. It is also
possible to connect the output of a remote control receiver. The input can be protected
with a single 10K
Ω EOL (end–of–line) resistor.
6) S1, S2 – Siren 1 and Siren 2 Outputs
Two siren outputs connected to the same on-board sound generator (driver). Connect the
siren 2 connection to a ground (-) connection. Each siren has a dedicated automatic
thermal fuse F2 and F3.
7) RELAY – Internal Relay Connections
Three connections to a relay mounted on the PCB. Can be used to activate various
auxiliary accessories such as external lighting, CCTV, external communicator, electric
locks, etc.
The three outputs are
C (common), NO (normally open) and NC (normally closed).
8) SMOKE – Switched Ground
Switched GND for smoke detectors that require reset. Any zone can be programmed to be
a “smoke detector” input; its activation will cause the GND to disconnect for
approximately two minutes.
Manual reset is obtained by pressing and holding the
#
RESET
key.
9) KEYPAD – Connection to Keypads
There are four Keypad terminals: Voltage power supply ( – ) and ( + ) . OUT is for data from
the control panel to the keypad, and
IN is for data from the keypad to the control panel.
An automatic thermal fuse F4 protects the 13.8 VDC power supply. Up to 8 keypads with
LCD display can be connected simultaneously.

Hunter-Pro Installation Manual
9
10) ALRM and ON/OFF – Auxiliary Outputs
These outputs have two conditions: ‘disconnect’ or ‘short to ground’. The outputs indicate
auxiliary units’ system status and alarm status.
11) TMPR1 and TMPR2 – Tamper Inputs
Inputs for tamper switches from detectors and metal box. Can be connected with/without
an end–of–line resistor. Different responses can be programmed for ON and OFF system
status. These inputs can serve as indicators other than tamper, for example: thermostat, 24
hours zone monitoring, panic button etc.
12) LINE – Connection to Telephone Line
Telephone line connection to dial to private numbers and Monitoring Stations, and for
remote programming. For best results connect as close as possible to the line source to
provide best protection against tampering.
13) SET – Connection to Telephone Set
Connection to a telephone set or answering machine. Do not connect a fax machine or
modem if you enable “line snapping”.
14) AUD IN, AUD OUT, CONT – Connections to Microphone and Voice modules
CONT activates voice and microphone modules VU-20 and MIC-100. Connect AUD IN
and AUD OUT to the audio outputs from the microphone and voice modules. (Refer to
sections 3.2.2.3 and 3.2.7.1.3)
15) JP4 - Serial Input
JP4 connects to a wireless detector receiver and home control system. Also connects to
LCL-11A serial RS-232
16) JP3 – Connection to Expansion Cards
Connection to Output Expansion Cards OUT-1000 and EXP-PRO. (Refer to sections. 6.1
and 6.2)
17) JP2 KEYPAD – Connection to Technician Keypad
Connection to Technician Keypad and LCL-11A for local and PC assisted programming of
the system.
18) TRANSMITTER – Connection to Long-Range Radio Transmitter
Connection to PIMA radio transmitters.
19) JP5-Select Siren Type
Connection to two types of sirens: with internal oscillator/driver/ speakers or without
internal oscillator/ driver/ speakers. Designated for sirens consuming up to 200 mA.(Refer
to section 2.5).
20) JP6-Select Siren Power Source
Connection to power source for sirens consuming over 200mA (Max is 3A). (Refer to
section 2.5)

Hunter-Pro Installation Manual
10
Empty Page

Hunter-Pro Installation Manual
11
Chapter 2
Installing Peripherals
2.1 General
Connect the various accessories according to the following diagram and instructions.
IMPORTANT!
Always disconnect battery and mains power supply when you connect and disconnect wires.
TMPR
2
TM PR
1
ON/
OF F
ALARM
KEYPAD
HUNTER
PRO
EXPANSIO N CARD SERIALKEYPADTRANSMITTER
U3
Z 1 Z2 Z3 Z4 -+ Z 5 Z6 Z7 Z8 -+ KEY -S1S2CN.ON.C
-
SIREN RELAY SMOKE
-+IN
OUT
F 3.15A 250VAC
F 5A 250VAC
CA
F5
T1
12 V D C
7.2AH MA X
10 K ¼ W
10K ¼W
10K ¼W 10K ¼W
10K ¼W
(-)(+)
SMOKE
DTECTO R
AC 14v
JP1 JP2 JP4
N.C.
STAN DART
WIRING
N.O.
STANDAR T
WIRING
TAMPER
TELEPHONE
SET
VU-20/
MIC-100
TELEPHONE
LIN E
JP5
F3
F1
F6
JP6
1
F4
U2
F7
F2
LINE SET
AUD
CONT
IN O UT
RX-150,
RX-160,
orRX-200
RX-400
RX-410
Connecting Accessories
IMPORTANT!
Disconnect all sources of power supply before proceeding with the installation!

Hunter-Pro Installation Manual
12
2.2 Zone Inputs
You can connect each zone input with or without Single or Double end–of–line (EOL)
resistors. Define each zone in the “system configuration” accordingly. The number of
resistors you connect (one or two) is defined as a general rule for all the zones. (Refer to
sections. 3.2.2 and 3.2.7.1.1)
2.2.1 Connection without EOL resistor
Connect a detector with NC output (for example, Defender) without EOL resistor
according to the below diagrams.
There are several options to connect the tamper outputs from the detectors: serial
connection that can be connected to the tamper input in the control panel, or to a zone
that is defined to as “24 hours”.
The Tamper can also be connected in serial to the relay output of the detector.
If you use the NO output from the detector then the zone should be configured as such.
For zone configuration, refer to sections. 3.2.2.1 to 3.2.2.6; for tamper configurations,
refer to section 3.2.7.1.2.
+-
JP2
JP1
PIR1
TAMPER NC RELAY NC
Zone
Common Common
Tamper Zone
+-
JP2
JP1
PIR1
TAMPER NC RELAY NC
Zone
Common
Separate connections for the relay and
TAMPER outputs
TAMPER in serial to the detector relay

Hunter-Pro Installation Manual
13
2.2.2 Connection with one EOL resistor
Connect a detector with NC output (for example, Defender) with one EOL resistor
according to the below diagrams.
There are several options to connect the tamper outputs from the detectors: serial
connection that can be connected to the tamper input in the control panel, or to a zone
defined as “24 hours”.
NOTE:
Connect one EOL resistor to all Tampers that connected in a serial configuration.
If you use the NO output from the detector then the zone should be configured as such.
For zone configuration, refer to sections 3.2.2.1-3.2.2.6; For tamper configurations, refer
to section 3.2.7.1.2.
EOL resistor with a Normally Closed (NC) PIR
TAMPER
PIR (NC)
10K ¼W
Zone (-)
+-
JP2
JP1
PIR1
TAMPER NC RELAY NC
Zone
Common
10K ¼W
+-
JP2
JP1
PIR1
TAMPER NC RELAY NC
Zone
Common Common
Tamper Zone
10K ¼W 10K ¼W
One EOL resistor
connected to a NC
detector
One EOL resistor in serial to the
relay and the TAMPER
Separate connections for the
relay and the TAMPER; each
with a dedicated EOL resistor
EOL resistor with a Normally Open (NO) PIR
PIR (NO)
10K ¼W
TAMPER
Zone (-)
+-
JP2
JP1
PIR1
TAMPER NC RELAY NO
Zone
Common
10K ¼W
+-
JP2
JP1
PIR1
TAMPER NC RELAY NO
Zone
Common Common
Tamper Zone
10K ¼W
10K ¼W
One EOL resistor
connected to a NC
detector
One EOL resistor in serial to the
relay and the TAMPER
Separate connections for the
relay and the TAMPER; each
with a dedicated EOL resistor

Hunter-Pro Installation Manual
14
2.2.3 Connection with two EOL resistors
Connect a detector with NC output (for example, Defender) with two EOL resistors
according to the below diagrams.
If you use the NO output from the detector then the zone should be configured as such.
For zone configuration, refer to sections 3.2.2.1-3.2.2.6; For tamper configurations, refer
to section 3.2.7.1.2.
Two EOL resistors with a Normally Closed (NC) PIR
TAMPER
Zone
10K ¼W
PIR (NC)
13K ¼W
(-)
+-
JP2
JP1
PIR1
TAMPER NC RELAY NC
Common
13K ¼W
10K ¼W Zone
Two EOL resistors with a NC output Two EOL resistors connected to a TAMPER in
serial connection to a NC output
Two EOL resistors with a Normally Open (NO) PIR
TAMPER
Zone
10K ¼W
PIR (NO)
(-)
13K ¼W
+-
JP2
JP1
PIR1
TAMPER NC RELAY NO
Common
13K ¼W
10K ¼W Zone
Two EOL resistor with a NO output Two EOL resistors connected to a TAMPER in
serial connection to a NO output

Hunter-Pro Installation Manual
15
2.3 Arming with Key/Remote Control
Connect the key or remote control receiver according to the below diagram with a 10k Ω
EOL resistor at the terminal input on the PCB. The key can have either a ‘momentary’ or
‘fixed’ type of switch.
NOTE:
Make sure momentary key is programmed when connecting remote control.
Z5 Z6 Z7 Z8 -+KEY -S1 S2
SIREN
F3
F2
10K
¼W
CONTROL PANEL
Key
Key (NC)
10K ¼W
(-)
Key
Key (NO)
(-)
10K ¼W
Key
Key (NC)
(-)
NOTE:
Program the Key input for an EOL resistor and the type of key; momentary or fixed (refer to section
3.2.7.1.2) . The Key input can be used to arm the system to HOME1 (refer to section 3.2.7.1.1)
2.4 TMPR1 and TMPR2
These inputs are used to monitor the control panel box, detector housings (in case EOL
resistors are not used, refer to section 2.2.1), and siren cases with tamper switches. This
input can also be utilized for panic buttons, temperature sensors with dry contact outputs
and more.
Connect the tamper switch to the input, TMPR1 or TMPR2 and the ground (–). A 10 k
Ω
EOL resistor at the terminal input on the PCB. The EOL resistor provides a
short/disconnect indication since the tamper switches are of the NO type.
NOTE:
Default programming is that both TAMPER inputs are enabled and without EOL. Refer to the “System
Configuration” screen in order to change the defaults (section 3.2.7.1.2).
TMPR
2
TMPR
1
ON/
OFF
ALARM
KEYBOARD
-
SMOKE -+INOUT
LINE
F4
JP5
Z5 Z6 Z7 Z8 -+KEY -S1 S2
SIREN
F3
F2
TAMPER
CONTROL PANEL

Hunter-Pro Installation Manual
16
2.5 Sirens
You can connect three types of sirens:
 Sirens without internal oscillator/ driver/ speakers ( AC ):
Connect each siren to terminals SRN1, SRN2, and ground (–). The sirens will be activated
by the oscillator of the HUNTER-PRO. Verify that pins 2 and 3 are shorted by Jumper JP5
(factory default).
SIREN KEYBOARD
JP5
Z8 -+KEY -S1 S2 C N.O N.C -
RELAY SMOKE -+INOUT
F4
F3
SIREN 1
SIREN 2
GND
F2
 Sirens with internal oscillator/ driver/ speakers (Low Current DC ):
Short pins 1 and 2 on Jumper JP5 and then connect the self drive siren as following:
SIREN KEYBOA
R
JP5
Z8 -+KEY -S1 S2 C N.O N.C -
RELAY SMOKE -+I
N
F3
F2
A SELF
DRIVEN
SIREN
CONTROL
 High Current DC Sirens (consuming over 200 mA):
If the siren consumes more than 200mA shoorten pin 2 and 3 in JP6, OR connect the (+) of
the siren to an external power source (battery).
2.6 Relay
Connect the relay connections NO, NC and COM as required by your installation. The
relay can be used to activate devices like lighting, CCTV, external sirens, and more. The
relay is activated by a zone, relay code, remote touch-tone commands from a telephone,
and response to failures (refer to section. 3.2.8).

Hunter-Pro Installation Manual
17
2.7 ALARM and ON/OFF
These outputs serve various purposes:
 Output ON/OFF follows the system status (ON or OFF) and can trigger external devices
accordingly.
 Output ALARM follows the Alarm status and can be used to trigger external devices such
as CCTV or strobe.
NOTE:
During programming, output ON/OFF is referred to as AUX1 and output ALARM as AUX2.
2.8 Keypads
Up to 8 keypads of all supported types can be simultaneously connected in parallel (for
‘supported types’ refer to chapter 7). Connect all four wires coming from the keypad to (–), (+),
IN and OUT
NOTE:
In older keypad models, there is color-coding: yellow wire =OUT, orange wire =IN, red wire= +
brown wire= - . However, in later keypad models, there is no color-coding. Instead, check for
connecting information on the inner side of the keypad’s case (diagram sticker).
IMPORTANT!
Do not use the power supply of the keypads for detectors and vise versa. The power supply for the
keypads must originate only from the control panel.
TMPR
2
TMPR
1
ON/
OFF
ALARM
KEYBOARD
JP5
-S1S2CN.ON.C
-
SIREN RELAY SMOKE -+IN
OUT
F4
F3 CONTROL PANEL
2.9 Telephone
Connect the pair of wires coming from the telephone provider to the LINE terminals.
Connect all other telephony devices to the
SET terminals. In case of alarm, the devices
will be disconnected and the system will be immediately connected to the telephone line.
The HUNTER-PRO should be the first device to connect to the telephone line (LINE
terminals) for best “Line Snapping” results.

Hunter-Pro Installation Manual
18
TMPR
2
TMPR
1
ON/
OFF
ALARM OUT
F4
T1
TELEPHONE WALL JACK
CONTERL PANEL
LINE SET
AUD
CONT
IN OUT
IMPORTANT!
If Line Snapping is enabled, you cannot connect a fax machine or modem to the SET terminals.
2.10 Microphone
The Microphone unit MIC–100 is used for listen-in via the
telephone line
Use only one of the zone (
+ ) terminals on the control panel as a
power source for the microphone
JP5
Z5 Z6 Z7 Z8 -+KEY -S1 S2
SIREN
F3
F2
TMPR
2
TMPR
1
ON/
OFF
ALARM OUT
F4
T1
CONTROL PANEL
LINE SET
AUD
CONT
IN OUT
.
MIC-100 .
IN
OUT
+
- (GND)
2.11 Voice Unit
The Voice Unit VU–20 plays a pre-recorded message when
the alarm is triggered, instead of a synthesized tone over the
telephone line.
Use only one of the zone (
+ ) terminals on the control panel
(except for the keypad’s) as a power source for the Voice Unit.

Hunter-Pro Installation Manual
19
JP5
Z5 Z6 Z7 Z8 -+KEY -S1 S2
SIREN
F3
F2
TMPR
2
TMPR
1
ON/
OFF
ALARM OUT
F4
T1
RED
BLACK
CONTROL PANEL
LINE SET
AUD
CONT
IN OUT
VOICE
UNIT
VU-20
TR(+)
AUDIO
GND
+V
2.12 Radio Transmitter TRV/TRU-100
The TRV–100/ TRU-100 is a long-range radio transmitter for communicating with a
Monitoring Station.
IMPORTANT!
Note the below mounting guidelines for installing a Control Panel with an integrated transmitter.
Following these guidelines will minimize RF interference:
* Do not mount the Panel close to a metal wall or ceiling
* Make sure you leave enough space for the antenna between the metal box and the ceiling
* Install the antenna at a distance from the Control Panel’s wiring
* Mount the antenna after you complete all other installations
* Make sure the antenna is straight
* Close the HUNTER-PRO metal box when performing transmission tests
2.12.1 Connecting the Transmitter:
NOTE:
The TRV/TRU-100 can transmit in two frequencies.
1. Mount the HUNTER-PRO’s metal box on the wall
2. Screw the transmitter to the box (4 screws at the base of the antenna.) Make sure the
screws are tightened; else, the transmitter’s range can be reduced.
3. Connect the antenna to the transmitter. Make sure the antenna is straight.
4. Make sure the 5-pin cable is connected to the transmitter’s Molex (named: “To the
system” on the transmitter’s sticker.)
5. Connect the other end of the 5-pin cable to the male Molex, placed on the Control
Panel’s upper left side (named “Transmitter” on the Control Panel.)
6.
If you wish to operate both frequencies, skip this step, since by following it the
transmitter will operate only with the second frequency:
Connect the 2-pin cable to the transmitter’s F2 Molex (named F2 on the transmitter’s
sticker.) Connect the other end of the 2-pin cable to a negative (-) output on the Control
Panel.

Hunter-Pro Installation Manual
20
2.13 Expanders
The HUNTER-PRO basic configuration includes 8 on-board input zones, two Tamper
inputs, two siren outputs, one 2 Amp NC/NO relay output, Smoke & PGM transistor
outputs, and two auxiliary outputs (also referred as Alarm & ON/OFF outputs).
These I/O capabilities can be expand using different add-on cards and/or systems. Input
zones can be connected to wired and/or wireless detectors and sensors. Currently the
HUNTER-PRO is limited to a total of 16 input zones and 15 outputs (10 auxiliary). The
extra I/Os can be gained using one of the following methods:
2.13.1 Outputs:
OUT-1000 : Eight outputs expansion card used for connecting and activating different
auxiliary devices (e.g., CCTV, relays, lights, etc.) as a response to system events and/or
alarm from specific zones (detailed description in sections 3.2.5.2 and 6.1.)
2.13.2 Input Zones:
EXP-PRO : Eight zones expansion card used for local connection of additional eight
wired zones. These zones are identical to the main PCB zones in features and
programming (detailed description in section 6.2.)
RC-PRO : Eight to sixteen wireless zones receiver. The wireless receiver is used to
connect wireless detectors, sensors, and remote controls to the HUNTER-PRO (detailed
description in section 2.15 and in the RC-PRO installation manual.)
NOTE:
It is possible to use all 16 zones as wireless zones but then no wired zones can be connected to the
HUNTER-PRO.
Zone Doubling : This is an option to expand the number of zones to 16 without any
additional hardware. This technique is called ‘Zone Doubling’ and it uses the Smoke
output, a resistor, and a diode (detailed description in section 6.3.)
IMPORTANT!
Doubled zones cannot be protected with two EOL resistors.
4 screws (at the base of the antenna)
Molex for connecting 5-pin cable
Molex for connecting 2-pin cable
Connection to program connector
Cable connections in TRV/TRU-100 transmitter