Pima Captain 8 Hunter-Pro 832 User manual

HunterPro
832/896/8144
Captain8
Security
S y s t e m s  
UserGuide 

2 HUNTER-PRO Series & CAPTAIN 8 User Guide
Quick Reference
Key Press for 2 seconds, enter
User code and press the key to... Press the key for 2 seconds
∗
to...
Arm to full mode, disarm uickly arm to full mode
*
Display the log -
Temporarily bypass zones -
Arm to “Home 1” mode uickly arm to “Home 1” mode
*
Display modes menu Display the “All Zones” mode for a minute
Set the telephone numbers -
Arm to “Home 2” mode uickly arm to “Home 2” mode
*
Set time and date -
Set the user codes -
Set the chime per zone
Turn ON/Off
the chime
feature in chime
zones
Set auto-arming by day and inactivity -
-
Reset smoke detectors.
Press briefly: display armed partitions
- Silence the keypad buzzer when it beeps
Display the system’s name & version Display the service provider
Initiate system tests -
- Display the system’s name & version
+ Press for 2 seconds: create Panic alarm
+ Press briefly: turn ON/OFF the keypad chime
Factory default codes
Master: 5555
Technician: 1234
∗
Commands marked with an asterisk must be enabled by the Installer.
1
11
1
ON/OFF
3
33
3
BYPASS
ENTR
ENTRENTR
ENTR
ENTR
ENTRENTR
ENTR

HUNTER-PRO Series & CAPTAIN 8 User Guide 3
Table of Contents
1 INTRODUCTION .................................................................................................... 5
1.1 Hunter-Pro & Captain 8 mutual features .................................................................. 5
1.2 Hunter-Pro eries unique features .......................................................................... 5
1.3 Captain 8 unique features ..................................................................................... 6
1.4 afety & ecurity ................................................................................................. 6
1.5 igns and conventions in this guide ........................................................................ 6
1.6 ystem codes ...................................................................................................... 7
1.6.1 The Master code ............................................................................................ 7
1.6.2 User codes ................................................................................................... 7
1.7 The User Menu .................................................................................................... 7
1.8 The LCD Keypad .................................................................................................. 7
2 ARMING & DI ARMING THE Y TEM (KEY #1) ......................................................... 8
2.1 Arming ............................................................................................................... 9
2.1.1 Via the keypad .............................................................................................. 9
2.1.2 Fast arming .................................................................................................. 9
2.2 Disarming ........................................................................................................... 9
2.2.1 With the DURE code ................................................................................... 9
3 THE Y TEM LOG (KEY #2) ................................................................................. 11
3.1 Log list sorting options ........................................................................................ 11
4 TEMPORARILY BYPA ING OPEN ZONE (KEY #3) ................................................. 12
4.1 When arming ..................................................................................................... 12
4.2 Prior to arming .................................................................................................. 12
5 “HOME 1” & “HOME 2” ARMING MODE (KEY 4, 7) ............................................... 13
6 DI PLAYING TYPE (KEY #5) ............................................................................... 14
6.1 Fast 32-zone display........................................................................................... 14
6.2 can open zones ................................................................................................ 15
6.3 Disable zone displaying ....................................................................................... 16
6.4 Other displaying types ........................................................................................ 16
6.4.1 All Zones ..................................................................................................... 16
6.4.2 Bypassed Zones ........................................................................................... 16
6.4.3 oaked Zones .............................................................................................. 17
6.4.4 Chime Zones ............................................................................................... 17
6.4.5 All Zones tatus ........................................................................................... 17
6.5 how partition names ......................................................................................... 18
7 PHONE NUMBER , M ETTING & DIALER TE T (KEY 6) ...................................... 18
7.1 Phone numbers .................................................................................................. 18
7.2 M messages................................................................................................... 19
7.2.1 A demo M message ................................................................................... 19
7.3 Dialer test ......................................................................................................... 19
8 ETTING TIME AND DATE (KEY 8) ........................................................................ 20
9 CODE (KEY 9) .................................................................................................. 20
9.1 The Master Code ................................................................................................ 20
9.1.1 Changing the code ........................................................................................ 21
9.2 User codes ........................................................................................................ 21
9.2.1 Adding or change a code ............................................................................... 21
9.2.2 Deleting a code ............................................................................................ 21
9.3 User name ........................................................................................................ 21
9.4 User settings ..................................................................................................... 22
9.5 Disarming Time Frame ........................................................................................ 23
9.6 User’s partitions ................................................................................................. 23
9.7 Adding a key fob ................................................................................................ 24
9.8 Deleting a key fob .............................................................................................. 24

4 HUNTER-PRO Series & CAPTAIN 8 User Guide
9.9 Adding RFID tag/keychain ................................................................................... 24
9.10 Deleting RFID Tag .............................................................................................. 25
9.11 The DURE code .............................................................................................. 25
9.12 The hort code .................................................................................................. 25
9.13 The Door code ................................................................................................... 25
10 AUTOMATIC ARMING (KEY 9) ............................................................................... 26
10.1 By day and hour ................................................................................................ 26
10.1.1 Inactivity auto-arming .................................................................................. 26
11 THE CHIME FEATURE (KEY #) .............................................................................. 27
11.1 Enabling and disabling the Chime globally ............................................................. 27
12 OTHER TOPIC ................................................................................................... 27
12.1 Partitions .......................................................................................................... 27
12.1.1 Examples .................................................................................................... 28
12.1.2 Displaying armed partitions ........................................................................... 30
12.2 Arming with key, key fob or RFID tag/key chain ..................................................... 30
12.2.1 Arming with a key fob ................................................................................... 30
12.3 Enabling Remote Upload ..................................................................................... 31
12.4 Names and Characters ........................................................................................ 31
12.4.1 Example ...................................................................................................... 32
12.5 PANIC alarm ...................................................................................................... 32
12.6 Resetting moke/Fire/Anti-mask detectors ............................................................ 32
12.7 Turning the keypad chime ON/OFF ....................................................................... 32
12.8 Comparison between the Hunter-Pro eries models ................................................ 33
12.9 Comparison between the Hunter-Pro 896 & Captain 8 ............................................. 33
13 MANUAL Y TEM TE T (BACK KEY) .................................................................... 34
14 REMOTE CONTROL VIA THE PHONE ...................................................................... 34
14.1 Basic mode ....................................................................................................... 34
14.2 Full mode .......................................................................................................... 35
14.2.1 Examples .................................................................................................... 36
15 TROUBLE HOOTING ........................................................................................... 37
16 APPENDIX: ZONE LOCATION TABLE ...................................................................... 39

HUNTER-PRO Series & CAPTAIN 8 User Guide 5
1INTRODUCTION
Congratulations on your purchase of the HUNTER-PRO Series and Captain 8 intruder alarm
systems. Much care has been taken in developing these systems, to provide you with
unprecedented peace of mind and security. The user-friendly menu with its advanced features
will professionally help you to protect your premises.
We recommend reading this guide in its entirely in order to familiarize you with the system and
take full advantage of its features.
To assure optimal safety and security, you should perform a system test once a week. See
section 13 for details.
For any further questions, please contact your local PIMA distributor.
1.1 Hunter-Pro & Captain 8 mutual features
•Hybrid systems with hardwired and wireless zones;
•Operating modes: full or partial, “HOME 1” & “HOME 2”;
•Equipped with menu-driven LCD and Graphic keypads, and cost-effective LED keypads;
•Optional use of partitions for perimeter zones and separate locations;
•Various automatic arming;
•Various codes & access options including RFID tag/keychain and key fob;
•Authorization settings per user;
•Up to four phone numbers to call the Monitoring Station and four to the owner;
•Optional disarming time frame per user;
•Constant zone, battery and phone line testing;
•Communication channels: phone, Long-range Radio, GSM, GPRS, Ethernet;
•Various ways to arm and disarm the system: keypad, key switch, RFID tag/keychain,
auto-arming;
•Full wireless detectors supervision;
•Optional alarm voice messages and listen in microphone;
•Various methods for preventing false alarms;
•Full log, part is non-volatile.
1.2 Hunter-Pro eries unique features
•8 to 32/96/144 zones;
•Up to 32/96/144 user codes and RFID tags;
•Phone remote control;
•Various partitioning options:
Up to 16 partitions;
Up to 8 subsystems.

6 HUNTER-PRO Series & CAPTAIN 8 User Guide
1.3 Captain 8 unique features
•8-16 zones;
•Up to 30 user codes & RFID tags;
•Various partitioning options:
Up to 4 partitions;
Up to 4 subsystems.
1.4 afety & ecurity
Both the HUNTER-PRO eries & the Captain 8 systems have been registered in
accordance with the EN60950 standard.
We advise you the following:
•The alarm system as well as its wiring should be placed in a hidden and safe location,
protected from rain or moisture.
•The alarm system may have hazards of electric shock and fire. Do not try to open the alarm
system’s case: dangerous high voltages are present inside it. Refer servicing to qualified
personnel only.
•This alarm system should be used with 230VAC 50Hz, protected by anti-electric shock
breaker. To prevent electric shocks and fire hazards, do NOT use any other power source.
1.5 igns and conventions in this guide
 Press a key briefly

Press a key for 2 seconds, until confirmation beep sounds
Warning
Note
In programming mode, moves the cursor to the right.
In programming mode, moves the cursor to the left.
Enter, Save
In programming mode, enables (‘+’) or disables (‘-‘) a parameter; erase character.
Press briefly: Cancel; Return.
Press for 2 seconds: Silence the keypad chime in faults.
The numbers that are printed above and below the keypad’s screen stand for zone
numbers and partition numbers.
NEXT
NEXTNEXT
NEXT
BACK
BACKBACK
BACK
ENTR
ENTRENTR
ENTR
#
##
#
END
ENDEND
END

HUNTER-PRO Series & CAPTAIN 8 User Guide 7
1.6 ystem codes
1.6.1 The Master code
•The Master code is a super user code with all the access authorizations.
•It is mainly used for changing the “Master Code” itself.
•The default factory Master Code is 5555.
Replace the default Master code immediately after installation to
prevent unauthorized and illegal operations.
1.6.2 User codes
•The User code is the user’s ID. It includes the User details, access authorizations,
disarming time frame and it is reported and logged together with any action the User
is taking.
•A User code can be restricted to only parts of the user menu, i.e., can only set
these menus.
1.6.3 hort Code
•A convenient, 2-digit code used only for arming the system.
1.6.4 Duress Code
•A code for using in distress situations.
•Entering the code disarms the system when armed and generates a silent alarm to
the Monitoring Station (if one is a subscriber) and to your phone.
•The code is a 4-6 digit code.
1.7 The User Menu
•The User menu is where parameters such as Time & Date, User codes and User
authorizations are set.
•It is accessed by pressing for 2 seconds and entering a User code. See section
9.4 for restrictions.
•By default, entering a User code arms or disarms the alarm system (toggle mode). The
Installer can program the system, so entering the code displays the User menu.
•After entering the User menu, the sub-menus are accessed directly, by pressing the
keypad keys. Each key menu is printed above it, e.g. “Time”, “Codes”.
1.8 The LCD Keypad
•RXN-400, RXN-410 and RXN-410 RFID are PIMA’s LCD keypads. They are designed for
maximum simplicity and durability and present decorative design.
The RXN-400 & RXN-410 are identical, except for their screen size: 410’s is larger.
0
00
0

8 HUNTER-PRO Series & CAPTAIN 8 User Guide
•The screen is made of 2 lines with 16 characters in each. The upper line displays the time
and the date (depending on the display type). Both lines display data regarding the
system, such as events, faults and zone status.
•Up to 8 supervised keypads can be connected to the system simultaneously.
•The message “Other Keypad in Use” is displayed when another keypad is in
use, or when the system is remotely controlled.
Figure 1. RXN-410 with the “Fast” display type
2ARMING & DI ARMING THE Y TEM
(KEY #1)
•The system can be armed in one of 4 ways:
1. Via the keypad;
2. Automatically;
3. Using Key fob, key switch and RFID tag/keychain;
4. In Hunter-Pro only: by a remote control and via the phone.
•As a rule, arming should be carried out only when all the zones are closed, but those on
the exit route, and there are no alarms (e.g., fire, panic) or faults (e.g., low battery):
In the “Fast zone” display type, no zone is indicated with a rectangle _ ;
In the “Scan open zones” display type, no zone is indicated with “OP” (open).
•Zones like exit doors and areas near the keypad are delayed on the exit and the entry, so
whoever arms (or disarms) the system will have enough time to walk from the keypad to the
door, (or the other way, when entering) without triggering any detector.
•The Exit & Entry delay times are separate and programmed by the Installer. The Installer
can also program two different Entry delays to different zones.

HUNTER-PRO Series & CAPTAIN 8 User Guide 9
2.1 Arming
•To arm your system, enter a user code (see section 9.4 for restrictions) or the Short code
(a code programmed by the Installer. See section 9.12).
•If no zone is open and there are no faults, the Exit delay countdown starts, the keypad
buzzer sounds beeps and the green ARMED LED flashes. You can now exit the premises
and close the door behind you
1
.
•When the Exit delay ends, the system becomes armed: the green ARMED LED stops to
flash and stays on, the beeps stop, the message “System Armed” is briefly displayed and
then the date and time are displayed.
2.1.1 Via the keypad
 User code ...
•The Exit delay time span is set by the Installer.
2.1.2 Fast arming
 until the Exit delay starts - R-  Short code ...
•Fast/single keystroke arming must be enabled by the Installer.
•To set the Short code, see section 9.12.
2.2 Disarming
 User code …
•To disarm the system, enter a user code.
•If an “Access denied” message is displayed, the user may be trying to disarm it outside
her/his “Disarming time frame”. See section 9.5
2.2.1 With the DURE code
 DURESS code …
•The DURESS code is a code to be used in threat situations, where you are being forced
to disarm the system. Hence, the code can be used only for disarming.
•Entering the DURESS code disarms the system and sends a silent alarm to the Monitoring
Station (if you are subscribed to) and your phones.
•To set the code, refer to section 9.3.
1
The Exit delay countdown can start immediately as soon as the final door is closed. Refer to the Installer.
Syst em Ar med!
1
11
1
Syst em Ar med!
Di sar mi ng. .
Di sar mi ng. .

10 HUNTER-PRO Series & CAPTAIN 8 User Guide
3THE Y TEM LOG (KEY #2)
 User code  
 
•The system logs alarms, arming & disarming, zone bypassing, faults, code changing and
other actions, chronologically.
•Any action taken by a user is logged with the User name.
•Part of the log is non-volatile (see the table on page 33).
3.1 Log list sorting options
•A log entry contains, on the upper line, a serial number and the date & time stamp when the
entry (i.e., the event) was logged; the event details appear on the bottom line.
•The log has 4 list sorting options: “All the events”, which displays all the log entries in one
list, “Faults only”, “Zone alarms” and “Arming/disarming”.
•When you view one of these lists, pressing a number between 0-3, transforms to
corresponding list: 0-“All the events”, 1-“Faults only”, 2-“Zone alarms”, 3-“Arming/disarming”.
•Entry example: “Burglary” alarm in zone #4, called “Kitchen”; the two screens are displayed
intermittently.
User Menu
Choose 1, 2. . .

HUNTER-PRO Series & CAPTAIN 8 User Guide 11
4TEMPORARILY BYPA ING OPEN
ZONE (KEY #3)
•
Bypassing zones reduces the safety of your protected premises
: a
bypassed zone does not sound the alarm when violated, nor does it
report the monitoring station!
•It should be used carefully, only if there is no alternative and only for
the shortest possible time.
•If you bypass a zone due to a fault, a service technician should
be called
•Beware not to bypass zones unintentionally
•Zones can be bypassed only when the system is disarmed
•Temporarily bypassed zones are automatically reinstated when the system is disarmed.
•The letter “B” in “Fast zone display" mode indicates a bypassed zone.
•A service technician can permanently bypass a zone, such in the case of a zone that no
longer needs to be protected
4.1 When arming
 User code to temporarily bypass the open zone/s
 .... - R- to cancel arming 
•When you try to arm the system and a 24-hour zone
2
is open, the keypad sounds beeps
and the message “Open Zone! Press END or Bypass”, with the zone/s details, is displayed
in two intermittently changing screens.
•If you do not cancel arming or bypass the open zones, when the Exit delay ends the
system will be armed, but the open zones instantly sound the alarm.
•Exit delayed zones are such, so they can be left open until the EXIT delay time ends.
4.2 Prior to arming
•You can temporarily bypass zones in advance of arming the system.
As a precaution, there is a time limit, set by the Installer, for a zone to be
bypassed prior to arming. When this time ends and the system has not been
armed yet, the zone is automatically reinstated.
2
24-Hour zones sound the alarm whenever they are violated, regardless of the system status.
3
33
3
BYPASS
Ar mi ng. . .
Ex i t Del ay 60
Syst em Ar med!
END
ENDEND
END

12 HUNTER-PRO Series & CAPTAIN 8 User Guide
•To temporarily bypass a zone prior to arming:
  User code   zone number  …
approval message is displayed.
•For example:
Be aware that a zone is bypassed immediately and stays so, until the
system is disarmed the next time (unless bypass limit time is over).
•To reinstate a bypassed zone:
  User code   zone number  …
approval message is displayed.
•For example:
5“HOME 1” & “HOME 2” ARMING
MODE (KEY 4, 7)
•“HOME 1” and “HOME 2” are arming modes, in which only some zones are armed, while
others are not: while the armed zones sound the alarm if violated, the disarmed zones can
be occupied at the same time.
•Common applications for the Home modes are perimeter detectors and nighttime zones.
•The zones included in each Home mode are set by the Installer and require no
hardware installation.
•Arming to the Home modes is much like arming to full mode, and there is fast arming
option too.
•To arm to “HOME 1” mode :   User/Short code
•To arm to “HOME 2”
mode:   User/Short code
3
33
3
BYPASS
Zone Number : 1
Ent r - Conf #- Rst
ENTR
ENTRENTR
ENTR
3
33
3
BYPASS
Zone Number : 1
Ent r - Conf #- Rst
#
##
#
Home 1 Ar mi ng. .
Exi t Del ay 60
Home 2 Ar mi ng. .
Exi t Del ay 60

HUNTER-PRO Series & CAPTAIN 8 User Guide 13
•To arm to the Home modes via the User menu:  User code  for
“Home 1” or  for “Home 2”.
•The Exit delay for both Home modes can be cancelled by the Installer.
6DI PLAYING TYPE (KEY #5)
  User code 
Di spl ay Type:
Fast Zn. Di spl ay

Di spl ay Type:
Sc an Open Zones

Di spl ay Type:
Di sabl e Zn. Di sp

Di s pl ay Ty pe:
Al l Zones

Di spl ay Type:
Di spl ay Bypass Z

Di spl ay Type:
Di spl ay Soak Zn.

Di spl ay Type:
Di spl ay Chi me Zn

Di spl ay Type:
Al l Zones St at us

Di spl ay Type:
Show Par t Name
•Your keypad has few options for displaying information on zones, alarms, faults etc.
•There are two basic displaying types: single screen and scrolling.
•Other types display various information for a minute, before they return to one of the
basic types.
•Zone names are programmed by the Installer.
6.1 Fast 32-zone display
  User code 
Di spl ay Ty pe:
Fast Zn. Di spl ay

•This display type is best used in systems with up to 32 zones. Each line displays 16 zones.
•The zones are displayed in a single screen, with their status represented by signs and letters.
•Each sign appears next to the related zone number, which is printed above & bellow the
keypad screen. See Figure 1.
•If the number of zones is no more than 16, information in the top line includes time, date
and system status. If the system is configured with more than 16 zones, this information
will not be displayed, but the other 16 zones.
Figure 1. Fast zone mode with 16 zones
NEXT
NEXTNEXT
NEXT NEXT
NEXTNEXT
NEXT
NEXT
NEXTNEXT
NEXT NEXT
NEXTNEXT
NEXT NEXT
NEXTNEXT
NEXT
NEXT
NEXTNEXT
NEXT NEXT
NEXTNEXT
NEXT NEXT
NEXTNEXT
NEXT
ENTR
ENTRENTR
ENTR

14 HUNTER-PRO Series & CAPTAIN 8 User Guide
•The system indicators on the top line (between the time and the date) are:
Indicator Description
P The system is communicating or testing the phone line
T The system is communicating over the Radio
R The RELAY output is active
S The SIREN output is active
•The zone status indicators are:
Indicator Description
- Closed (not triggered) zone
_ Open (triggered) zone. If the zone has more than one status (e.g., it is
open and alarming), the indications are displayed intermittently.
A Alarmed zone: the zone was violated when the system was armed, or is
alarming now.
B Bypassed zone
C Chime zone
F Zone failure (disconnection) or a TAMPER switch is open
L Low battery in a wireless detector
Opened 24-hour zone or armed partition. Press to display the
armed partitions.
S Short in the zone's wires
T The zone is in soak (test) mode
V A wireless detector is not responding
6.2 can open zones
  User code  
Di spl ay Ty pe:
Sc an Open Zones

•The system continuously scans the zones and the system’s status, and displays open
zones, faults and alarms.
•The information is displayed in scrolling mode.
•For example:
#
##
#
5
55
5
NEXT
NEXTNEXT
NEXT
ENTR
ENTRENTR
ENTR

HUNTER-PRO Series & CAPTAIN 8 User Guide 15
•The zones’ status indicators are:
Indicator Description
P Open zone
AL The zone was violated when the
system was armed, or is alarming now.
BP Bypassed zone
FL Zone Cut
SH Zone Short
SV Zone supervision
LB Wireless zone low battery
AM Anti-mask zone
6.3 Disable zone displaying
  User code   X2 
•The zones’ status is not displayed, only alarms and faults (if there are any).
6.4 Other displaying types
•  to the next displaying types.
•The other types display various information. After pressing the information is
displayed for a minute.
•See the display types menu in the beginning of section 6.
6.4.1 All Zones
  User code   X3   zone number
 repeatedly
•The properties of every programmed zone - name, partitions and type - are displayed
when pressing repeatedly.
6.4.2 Bypassed Zones
 
User code   X4  to display other
bypassed zones - R -  repeatedly to display the zone’s name, partitions and type.
•Permanently and temporarily bypassed zones are displayed in this type.
•Permanently bypassed zones are set by the Installer.
•Temporarily bypassed zones will be automatically reinstated the next time the system
is disarmed.
5
55
5
NEXT
NEXTNEXT
NEXT
Di spl ay Ty pe:
Di sabl e Zn. Di sp
ENTR
ENTRENTR
ENTR
NEXT
NEXTNEXT
NEXT
ENTR
ENTRENTR
ENTR
5
55
5NEXT
NEXTNEXT
NEXT
Di s pl ay Ty pe:
Al l Zones
ENTR
ENTRENTR
ENTR
ENTR
ENTRENTR
ENTR
ENTR
ENTRENTR
ENTR
5
55
5
NEXT
NEXTNEXT
NEXT
Di spl ay Type:
Di spl ay Bypas s Z
NEXT
NEXTNEXT
NEXT
ENTR
ENTRENTR
ENTR

16 HUNTER-PRO Series & CAPTAIN 8 User Guide
6.4.3 oaked Zones
  User code   X5  to display other
soaked zones - R -  repeatedly to display the zone’s name, partitions and type.
•A zone is set as Soak (test) zone by the Installer/Service technician, when it is
repeatedly faulty.
•Soak zones, as well as soak period (up to a week), are set by the Installer/Service technician.
•Soak zones are automatically reinstated when the soak period is over.
6.4.4 Chime Zones
  User code   X6  to display other
chime zones - R -  repeatedly to display the zone’s name, partitions and type.
•Chime zones trigger the keypad chime when opened.
6.4.5 All Zones tatus
  User code   X7 
  ....
•This type is intended to display the status of all the programmed zones quickly.
•It is design the same as the “Fast zone” type, 10 zones in each line, and 20 in every
screen. See section 6.1 for details on the signs.
•In the above screenshots, the first screen displays the status of zones 1 - 10 and 11 - 20.
Statuses for example are:
Zone #1: chime zone.
Zones #2-3: closed zones.
Zones #4-6: open zones.
Zone #7: chime zone.
Zone #8: bypassed zone.
Zones #9-10: closed zones.
Zone #12: zone fault.
Zone #15: zone activated the siren.
Zone #22: chime zone.
Zone #34: bypassed zone.
5
55
5
NEXT
NEXTNEXT
NEXT
Di s pl ay Ty pe :
Di s pl ay Soak Zn.
NEXT
NEXTNEXT
NEXT
ENTR
ENTRENTR
ENTR
5
55
5
NEXT
NEXTNEXT
NEXT
Di spl ay Type:
Di spl ay Chi me Zn
NEXT
NEXTNEXT
NEXT
ENTR
ENTRENTR
ENTR
5
55
5 NEXT
NEXTNEXT
NEXT
Di spl ay Ty pe:
Al l Zones St at us
ENTR
ENTRENTR
ENTR
NEXT
NEXTNEXT
NEXT NEXT
NEXTNEXT
NEXT

HUNTER-PRO Series & CAPTAIN 8 User Guide 17
6.5 how partition names
  User code   
•This is a toggle display type: when it is enabled, the names of the partition/s (see section
12.1 for details) this keypad is allocated to, are constantly displayed.
•To disable this mode, repeat the process.
•This mode requires the “Scan Open Zones” display mode to be selected first.
7PHONE NUMBER , M ETTING &
DIALER TE T (KEY 6)
  User code   
•Key #6 has three sub-menus:
“Edit Numbers”, to set your phone numbers for receiving alarms and other messages
from the system;
“SMS Settings”, to set which of your phones will receive SMS messages instead of
alarm messages;
“Test dialer”, for testing the numbers you have programmed (without triggering
the sirens);
7.1 Phone numbers
  User code  
 phone #1  or ....
•The HUNTER-PRO Series & the Captain 8 have an integrated phone dialer, that can call up
to 4 numbers and sound an alarm, or send SMS alert or sound a recorded message.
•When an alarm is set off, the dialer attempts to call each number twice (i.e., a total of 8
attempts)
3
.; when the call is answered, the system sounds a Hi/Lo siren, or a voice message
4
.
•To set a number, enter it and

•To use “+”, “*”, “#” and “P” for one second delay:  repeatedly
3
SMS messages are sent only once to each number.
4
This feature requires the purchasing of the VU-20 voice module.
5
55
5
BACK
BACKBACK
BACK
Di spl ay Type:
Show Par t Name
ENTR
ENTRENTR
ENTR
Edi t Number s
ENTER/ NEXT/ BACK NEXT
NEXTNEXT
NEXT
SMS Set t i ng s
ENTER/ NEXT/ BACK
NEXT
NEXTNEXT
NEXT
Test Di al er
Sel ec t T. No. 1- 4
Edi t Number s
ENTER/ NEXT/ BACK
ENTR
ENTRENTR
ENTR
Pr i v . Phn 1<Del =#
ENTR
ENTRENTR
ENTR NEXT
NEXTNEXT
NEXT
Pr i v. Phn 4<Del =#
ENTR
ENTRENTR
ENTR
*
**
*

18 HUNTER-PRO Series & CAPTAIN 8 User Guide
•The dialer aborts the dialing attempts in the following cases:
The system is disarmed.
All numbers were dialed, each number twice (i.e., no call was answered).
In HUNTER-PRO Series only, a remote control command is received. See section 14.1.
7.2 M messages
  User code   
 to select a number (set it to “+”).  to move to the
next numbers.
•Text messages are an alternative way for you to receive alarms and faults reports.
•The numbers 1-4 stand for the corresponding phone numbers.
•A phone number that is set here to receive SMS messages will not receive the siren alarm.
•For example, phone #2 will receive SMS messages.
•Sending SMS messages requires the purchasing of the SMS-100 module or the GSM-200
cellular module.
7.2.1 Demo M message
•The details in the SMS messages are all taken from the system log.
•In this figure, the time and date indicate when the event was registered in the log, and not
when the message was sent.
7.3 Dialer test
  User code  
 ( / / ) ...
... ...
•Use the Dialer test menu to check the programmed phone numbers.
NEXT
NEXTNEXT
NEXT
SMS Set t i ng s
ENTER/ NEXT/ BACK
ENTR
ENTRENTR
ENTR
123 4
- - - - SMS Opt i ons
NEXT
NEXTNEXT
NEXT
1234
- +- - SMS Opt i ons
NEXT
NEXTNEXT
NEXT NEXT
NEXTNEXT
NEXT
Test Di al er
Sel ec t T. No. 1- 4
1
11
1
ON/OFF
3
33
3
BYPASS

HUNTER-PRO Series & CAPTAIN 8 User Guide 19
•Press a number between 1 and 4 to call the corresponding programmed number.
•If a call is not received, check that the number is correct; if it is, call a service technician.
•During the test, the system displays the communication process, as displayed above.
8ETTING TIME AND DATE (KEY 8)
  User code   time in the following format: hh:mm
  date in the following format: dd:mm:yy  
•  / to move to the left and right.
•To correct data,  and start over.
•You must keep the system’s clock accurate at all times, for maintaining a detailed log and
for functions such as user disarming time frame.
•If the clock is not set, a “Clock Not Set” error is displayed and the keypad beeps.
9CODE (KEY 9)
•Codes in the Hunter-Pro Series and Captain 8 systems are made of 4-6 digits (except for
the Short code).
•Duplicate codes or codes that start with same two digits as the Short code are not allowed.
•Codes are concealed with asterisks and cannot be revealed or restored in any way.
9.1 The Master Code
The default Master (5555) should be replaced immediately
after installation
(see how in this section).
•The Master code is a super user code, with all access authorizations. See section 1.6.1 for
more details.
•Its main use is changing the Master code itself.
9.1.1 Changing the code
 Master code  
 4-6 digits number 
Hour
00: 00
ENTR
ENTRENTR
ENTR ENTR
ENTRENTR
ENTR END
ENDEND
END
NEXT
NEXTNEXT
NEXT BACK
BACKBACK
BACK
END
ENDEND
END
User Menu
Choose 1,2...
9
99
9
CODES
Mast er Code
ENTER/ NEXT/ END
ENTR
ENTRENTR
ENTR
ENTR
ENTRENTR
ENTR

20 HUNTER-PRO Series & CAPTAIN 8 User Guide
•The “Master code” menu is visible only when entering the User menu with the Master code.
•Therefore, to change the code, you can only use the Master code.
•When entering the User menu with a User code and pressing “9”, the “User Codes” menu
is displayed.
9.2 User codes
•See section 1.6.2 for details about user codes.
9.2.1 Adding or change a code
  User code 
User 1 ( 1)
ENTER/ NEXT/ END

User number 
Ent r / Change Code
ENTER/ NEXT/ END

User 1
* * * * * * ( 4- 6)
 4-6 digit number

•An asterisk (*) appears to the right of the user’s name, notes the user code has been
assigned to this user. For example, “Linda” is user number 16:
9.2.2 Deleting a code
  User code  
User 1 ( 1) *
ENTER/ NEXT/ END

User number 
Del et e Code
ENTER/ NEXT/ END
 
•Once a code is deleted, the asterisk is deleted too and the code is available to be used for
another user.
9.3 User name
  User code   
user number   X2
User Name
ENTER/ NEXT/ END

User Name 1
User 1

name (up to 8 characters) 
9.4 User settings
  User code   
user number   X3 
9
99
9
CODES
Us er Co des
ENTER/ NEXT/ END
ENTR
ENTRENTR
ENTR
ENTR
ENTRENTR
ENTR ENTR
ENTRENTR
ENTR
ENTR
ENTRENTR
ENTR
9
99
9
CODES
Us e r Co d es
ENTER/ NEXT/ END
ENTR
ENTRENTR
ENTR
E N T R
E N T RE N T R
E N T R N E X T
N E X TN E X T
N E X T ENTR
ENTRENTR
ENTR
END
ENDEND
END
9
99
9
CODES
Us er Co des
ENTER/ NEXT/ END
ENTR
ENTRENTR
ENTR
User 1 ( 1) *
ENTER/ NEXT/ END
ENTR
ENTRENTR
ENTR NEXT
NEXTNEXT
NEXT ENTR
ENTRENTR
ENTR
ENTR
ENTRENTR
ENTR
9
99
9
CODES
Us e r Co des
ENTER/ NEXT/ END
ENTR
ENTRENTR
ENTR
User 1 ( 1) *
ENTER/ NEXT/ END
ENTR
ENTRENTR
ENTR NEXT
NEXTNEXT
NEXT ENTR
ENTRENTR
ENTR