Prevue Hendryx F040 User manual

Flight Cage
Model: # F040 [A]
read first REVIEW BEFORE ASSEMBLY
• TOOLS: Allen wrench (included). Needle nose
pl ers (not included) w ll be useful. If power
tools are used, Prevue s not respons ble
for damage caused by m suse.
•Two-person assembly for best results.
For ass stance or replacement parts,
please contact Prevue Pet Products:
TOLL-FREE 800.243.3624
ONLINE www.prevuepet.com
EMAIL customerservice @ prevuepet.com
F040 [A]— 03/15 — USL Made in China for Prevue Pet Products, Inc., Chi ago IL USA www.prevuepet. om 800 243-3624 ustomerservi e@prevuepet. om
1To assemble the BASE,
you will need these pieces:
2To assemble the SIDES,
you will need these pieces:
×4
×
×4
Flip assembled unit over
and fully insert casters into
frame legs.
Attach the storage shelf to the leg
frames to create the base. Back
ends of leg frames have a backstop
tab at the track ends (fig.1-1).
[ FIG. 1-1]
tack the side panels in place
on the base. For correct assembly,
note these details:
• top side panel: has a finished
corner (fig. 2-1).
• bottom side panel: top horizontal
surface has small holes near the
center and open-frame corners
(fig 2-2), to align with posts and
wires from the top side panel
(fig 2-3).
• nest doors swing out
Notes: Have an assistant holding
side panels for best results.
traighten extended wires or remove
hole slugs with needle nose pliers.
[ FIG. 2-1]
[ FIG. 2-2]
[ FIG. 2-3]

F040 [A]— 03 /15 — USL
3To assemble the BACK,
you will need these pieces:
4To assemble the ROOF,
you will need these pieces:
Back panels are identical and inter-
changeable. Install bottom panel by:
• inserting top extended wire into
the side frame (fig. 3-1);
• aligning bottom frame with hole
in side frame (fig. 3-2), and;
• securing panels together with a
screw in each lower corner (fig 3-3).
Repeat for top back panel (fig 3-4).
×2
×
×2
×
[ FIG. 3-1]
[ FIG. 3-2]
[ FIG. 3-3] [FIG. 3-4]
For more wonderful ages, toys, and a essories for dogs, ats, birds, hi kens, rabbits, ferrets and small animals, visit www.prevuepet. om
×4
×
• Align the roof panel with corners;
• Align extended wires from back
panel with holes on underside of
roof frame;
• Align extended wires of roof with
holes along side frames.
ecure roof with screws in each corner.
Note: The addition of the roof
stabilizes the cage during assembly.
The front two screws may be left
loose until the end of tep 5.

6To assemble the FRONT,
you will need these pieces:
F040 [A]— 03 /15 — USL
5To install PERCHES and CUPS,
you will need these pieces:
For more wonderful ages, toys, and a essories for dogs, ats, birds, hi kens, rabbits, ferrets and small animals, visit www.prevuepet. om
×3
×4
×
Hang food/water cups under
the doors in the side panels.
Insert perches around the
cage in appropriate places.
×2
×
×2
×
Loosen (but don’t remove) the two
front corner screws of the roof to
allow for installation of front panels.
• Align extended wires on lower front
panel with holes on side frames;
• align bottom corners with screw
holes on side frames.
• secure the panel loosely with
screws in each lower corner.
Remove the front two screws of the
roof completely. Have your assistant
hold the roof open slightly while
you align wires, holes and corners,
same as the lower front panel.
ecure the upper front panel with
screws in each lower corner.
Replace the screws in the upper front
corners of the roof panel.
Work your way around the entire frame
—front and back — tightening up all
screws for a secure and stable cage.

7To complete the assembly,
you will need these pieces:
F040 [A]— 03/15 — USL For more wonderful ages, toys, and a essories for dogs, ats, birds, hi kens, rabbits, ferrets and small animals, visit www.prevuepet. om
CLEANING INSTRUCTIONS
Prolong the life of your Prevue Pet Products
cage with these recommendations:
• When cleaning the cage, use a mild soap
and soft cloth or Teflon-resistant scrubber
(such as Prevue’s Cage aver non-abrasive
scrub pad [#109]).
• After washing, dry the cage thoroughly with
a dry soft cotton cloth to prevent rust.
• Wash the tray with soap and warm water.
Do not leave the tray in the sun to dry, as
the tray may warp. Hand-dry the grille and
tray with a soft cotton cloth before placing
back into cage.
lide the grille and the tray in place.
Install the windbell lock (fig. 6-1).
Your cage is now fully assembled and ready for use.