PROAIM SD-FUSN-00 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
1
Fusion 8 Versale Slider Dolly with Track System
(SD-FUSN-00)
Assembly Manua l
2x End Feet
8 Track
Camera Dolly with 100mm bowl Support Bracket
Mitchell Base 150mm Bowl 75mm
Conversion Ring
2x Safety
Wheels
4x Adjustable
Leveling Legs
3x Allen keys
4x Elasc Stoppers
3x Junior
Pin Adapters
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.

2
ATTENTION: PLEASE READ THIS BEFORE USING TO PREVENT SERIOUS DAMAGE TO THE
GEAR!
NEVER LEAVE THE FASTENERS LOOSE
Carefully ghten all the fasteners to prevent breakage to the equipment & any harm to crew. It ensures
protecon & stability.
DO NOT FORGET TO SECURE THE DOLLY
Always use Safety Wheels while mounng the dolly in Under-Slung or Inclined Mode. Not using it will
severely damage both the camera and equipment.
ALWAYS MOUNT DOLLY ON RIGID TRACK
Prevent the track from sagging by ng support bracket in the middle. Failing to do so will result in un-
steady footage.
NEVER STRIKE OR PUT METAL OBJECTS ON THE RAILS!
This can cause nicks and dings which will result in trembling movement and image vibraon!
BE CAREFUL WHILE MOUNTING TRACKS
Do ghten the knobs on track clamping bracket aer pung-in the rails. This ensures a secure grip to
your track setup and prevents an irreparable damage.
Aaching the Levelling Legs
• Insert adjustable leveling legs into the end
feet and ghten the knob to secure it.
Aaching the Track
• Loosen knobs on the end feet, insert track
rails into them, and re-ghten the knobs to
secure the rails.
Safety Hints
• Slide an extension secon in each end to
complete an 8 run. Next, install and
ghten the screws to secure them.

3
Assembling the Dolly Setup
• Mount the Camera Dolly onto the track, as
shown.
• Loosen & remove the center knob on both
sides of the dolly and aach the safety
wheels.
• Next, re-aach & ghten the knobs.
• Loosen the side knobs on both sides of the
dolly for lng the camera plaorm. Adjust
the posion at any angle and lock the knobs.
NOTE: The dolly plaorm inclines up to 52°.
• Aach elasc stoppers on both the rails to
perform as wheel brakes to prevent
dislocang the dolly.
NOTE: Fusion Dolly accommodates 4 Camera Mounng Heads.
75mm Bowl / 100mm Bowl / 150mm Bowl / Mitchell Base
• The top mount of the dolly comes equipped
with standard 100mm Bowl Receptacle.
• Add 75mm Conversion Ring to use 75mm
Bowl Head with Dolly.

4
• To use 150mm Bowl Head with Dolly, add
150mm Bowl Receptacle.
• To mount Mitchell base setups, remove the
100mm bowl receptacle from the dolly
plaorm & aach the mitchell plate to it.
Tighten screws using an allen key.
• Mount your camera setup, as desired.
Aaching the Supports
• Remove the hooks from the junior pin
adapters, insert them into the end feet on
both sides and aach the junior pin adapter
to the inserted hooks & ghten it by twisng
it.
• Loosen the knob xed on Junior Pin
Adapters, mount the track system onto any
stand (Not Included) via the adapters, and
ghten the knob back to secure it.
• Remove the hook from the small junior pin
adapter and insert it into the support brack-
et, as shown in the image.

5
• Aach the junior pin adapter to the hook
inserted into the support bracket & ghten
it by twisng it.
• Center the support bracket under the track
and mount your camera setup, as shown in
the image.
Underslung Dolly Setup
• Aach 100mm bowl receptacle to the
boom of the dolly and ghten screws using
an allen key.
• Mount your camera set up to take Under-
slung Shots.

6
YOUR PROAIM FUSION 8FT VERSATILE SLIDER DOLLY WITH TRACK SYSTEM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.