Profile Design DRV SIZER BAR User manual

DRV SIZER BAR
1
DRV SIZER BAR
version 01-03-16-2020

DRV SIZER BAR
2
Thank you for purchasing this adjustable width Profile Design Sizer Bar. This bar is compatible with a 31.8mm stem clamp. It is not compatible
with any clip on aerobar.
This bar is for bike fitting purposes only.
It is not to be used for riding on the road or track. It may only be used on an indoor trainer or adjustable fitting bike.
Please read these instructions thoroughly before attempting to install this item. Proper installation is required for compliance with Profile Design's
warranty policy. If you are not familiar with installation of handlebars or their accessories, please seek the assistance of your local Profile design
dealer by logging on to www.profile-design.com and using "dealer search" or by calling Profile Design's customer service number.
Tools and materials required:
• 3mm Hex Wrench
• Lithium grease
Your bar kit should contain:
• One (1) central sleeve (aluminium)
• Two (2) quick release levers
• Four (4) M4x0.7x10SHB bolts
• Two (2) DRV105 handlebar drops (right and left)
• Two (2) DRV120 handlebar drops (right and left)
• Two (2) DRV135 handlebar drops (right and left)
If anything is missing from the bar kit please contact your distributor.
INTRODUCTION

DRV SIZER BAR
3
COMPONENT LIST
01 01
04 0605 06
02 02
03 03
LR
LR
LR
QTY.
Req. Part# Ref.# Part Description
1 4332051DRV / SIZER Bar 105 Flat Black (R+L)
1 4332062DRV / SIZER Bar 120 Flat Black (R+L)
1 4332073DRV / SIZER Bar 135 Flat Black (R+L)
1 1893734Bracket - DRV / SIZER Bar Central Clamp Flat Black
4 3135245Bolt - M4*10 SHB
2 1893746Bracket - Quick-release M6*60L/56A Black

DRV SIZER BAR
4
PART DRAWINGS
105
70
122
120
75
136
135
80
148
W: 360mm 380mm 400mm 420mm
W: 400mm 420mm 440mm
W: 420mm 440mm 460mm

DRV SIZER BAR
5
Installation instructions
1. Apply a thin coating of Lithium grease to the inside faces of the central sleeve.
2. Insert the quick release levers with the lever to the front of the bar.
3. Insert the desired handlebar ends with the slot lining up with the bolt holes in the front of the sleeve.

DRV SIZER BAR
6
4. Insert the M4x0.7x10SHB bolts into the sleeve, passing all the way into the bar. These bolts are to prevent rotation of the bar during the fit.
5. Set the bars to the desired width.
6. Close the quick release levers with the lever oriented at a downwards angle.

DRV SIZER BAR
7
7. Install the bars on a fit bike or riders bike by clamping the central 31.8mm section and tighten the stem bolts to 6nm.
8. To change the bar width during a bike fit just open the quick release, reset the width and close the levers again.
9. To change the bar shape during a bike fit open the quick release levers, wind the anti-rotation bolts out far enough that the bar can be extracted
then repeat steps 3 to 6.

DRV SIZER BAR
8
• Profile Design Worldwide TwoYear Limited Warranty.
• Profile Design, LLC (distributor) warrants to the original retail purchaser ("you") that the
Profile Design product for which you received this warranty is free from defects in material
and workmanship for (2) two years from the date of original retail purchase. For more
details on this warranty, its exclusions and/or how to make a claim under the warranty
please call +1 310.747.0085 extension 161 or visit www.profile-design.com/pages/warranty
WARNING

DRV SIZER BAR
9
2677 El Presidio Street
Long Beach, CA 90810
Ph: 310-884-7756
w
ww.profile-design.com
© Profile Design LLC