protech prox SP-S154 User manual

USER
MANUAL
SP-SXX4 M3
SP-S154 / SP-S174
SP-S214
Intel®7thGen.CoreTM i7/i5/i3
ProcessorHighPerformance
andLowPowerPanelPC

SP-S154 / SP-S174 / SP-S214
High Performance Panel PC
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Mar. 2021. You may not reproduce
or transmit in any form or by any means, electronic, or
mechanical, including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have
high electrical voltage. We strongly recommend that only
qualified engineers are allowed to service and disassemble
the system. If any damages should occur on the system and
are caused by unauthorized servicing, it will not be covered
by the product warranty.

i
Contents
Revision History ............................................................................................ vii
1 Introduction ......................................................................................... 1-1
1.1 About This Manual ..................................................................... 1-2
2 Getting Started .................................................................................... 2-1
2.1 Package List ............................................................................... 2-2
2.2 System Overview ....................................................................... 2-3
2.3 System Specifications .............................................................. 2-12
2.4 Safety Precautions ................................................................... 2-18
3 System Configuration ......................................................................... 3-1
3.1 External I/O Ports Diagram ........................................................ 3-2
3.1.1 SP-S154 / SP-S174 / SP-S214 Rear I/O Ports Diagram .... 3-2
3.2 Jumper & Connector Quick Reference Table ............................. 3-3
3.3 Component Locations of System Main Board............................ 3-5
3.3.1 Top View of System Main Board BM-2502 ......................... 3-5
3.3.2 Jumper Settings of BM-2502RB-**N................................... 3-6
3.3.3 Bottom View of BM-2502RB-**N ........................................ 3-7
3.4 How to Set Jumpers ................................................................... 3-8
3.5 Setting Main Board Connectors and Jumpers ......................... 3-10
3.5.1 COM1, COM2, COM4 Port Pin9 Definition Selection
Guide…… ......................................................................... 3-10
3.5.2 COM Ports ........................................................................ 3-11
3.5.3 COM1 RS-232/422/485 Selection .................................... 3-14
3.5.4 COM1 RS-485 Auto Flow Selection .................................. 3-15

ii
3.5.5 LAN and USB 3.0 Ports .................................................... 3-16
3.5.6 LAN2 Port Enable Selection ............................................. 3-18
3.5.7 4 x 1 USB 2.0 Connectors ................................................ 3-19
3.5.8 Internal USB 2.0 Connector .............................................. 3-20
3.5.9 Dual DVI-D Ports (DVI1) ................................................... 3-21
3.5.10 DisplayPort Connector (Optional) ..................................... 3-23
3.5.11 HD Audio Connector ......................................................... 3-24
3.5.12 Printer Port Connector (Optional) ..................................... 3-25
3.5.13 Front Panel Connector ...................................................... 3-26
3.5.14 CPU Fan Connector.......................................................... 3-27
3.5.15 System Fan Connector ..................................................... 3-27
3.5.16 Half-Sized Mini PCI Express Slot (M_PCIE1) .................. 3-28
3.5.17 PCI Express Slots ............................................................. 3-29
3.5.18 SATA 3.0 Connectors ........................................................ 3-31
3.5.19 ATX Power Connectors..................................................... 3-32
3.5.20 AT / ATX Mode Selection .................................................. 3-33
3.5.21 SPI Connector ................................................................... 3-34
3.5.22 SPI Override Protection Selection .................................... 3-34
3.5.23 Case Open Detection Connector ...................................... 3-35
3.5.24 Intruder Detection Selection ............................................. 3-35
3.5.25 Low Pin Count (LPC) Connector ...................................... 3-36
3.5.26 Clear RTC Data Selection................................................. 3-36
3.5.27 VCCIO Voltage Selection .................................................. 3-37
3.5.28 BIOS Recovery Mode Selection ....................................... 3-38
3.5.29 Clear CMOS Data Selection ............................................. 3-39
3.6Component Locations of System Daughter Board .................. 3-40
3.6.1 Top View of System Daughter Board BR-8080 ................ 3-40
3.7 Setting Daughter Board Jumpers ............................................. 3-41

iii
3.7.1 VDD Selection ................................................................... 3-41
3.7.2 Backlight Voltage Selection .............................................. 3-42
3.7.3 PWM Voltage Selection .................................................... 3-43
3.7.4 LVDS (Low Voltage Differential Signaling) Resolution
Selection ........................................................................... 3-44
4 Software Utilities ................................................................................. 4-1
4.1 Introduction................................................................................. 4-2
4.2 Installing Intel® Chipset Software Installation Utility ................... 4-3
4.2.1 Introduction ......................................................................... 4-3
4.2.2 Intel® Chipset Software Installation Utility ........................... 4-3
4.3 Installing Graphics Driver Utility ................................................. 4-4
4.4 Installing LAN Driver Utility ......................................................... 4-6
4.5 Installing Intel® Management Engine Interface Driver ............... 4-7
4.6 Installing Sound Driver Utility ..................................................... 4-9
4.7 Installing Intel® USB 3.0 eXtensible Host Controller ................ 4-10
4.8 Installing eGalaxTouch Driver Utility ........................................ 4-11
4.9 Installing Intel® Rapid Storage Technology Installation ............ 4-12
5 BIOS SETUP ........................................................................................ 5-1
5.1 Introduction................................................................................. 5-2
5.2 Accessing Setup Utility ............................................................... 5-4
5.3 Main ............................................................................................ 5-7
5.4 Advanced ................................................................................... 5-9
5.4.1 Advanced – CPU Configuration ........................................ 5-10
5.4.2 Advanced – SATA Monitor ................................................ 5-11

iv
5.4.3 Advanced – ACPI Settings ................................................ 5-12
5.4.4 Advanced – PCH-FW Settings ......................................... 5-13
5.4.5 Advanced – F81866 Super IO Configuration .................... 5-14
5.4.5.1 F81866 Super IO Configuration - Serial Port 1
Configuration…................................................................ 5-15
5.4.5.2 F81866 Super IO Configuration - Serial Port 2
Configuration…................................................................ 5-16
5.4.5.3 F81866 Super IO Configuration - Serial Port 3
Configuration…................................................................ 5-17
5.4.5.4 F81866 Super IO Configuration - Serial Port 4
Configuration…................................................................ 5-18
5.4.5.5 F81866 Super IO Configuration - Serial Port 5
Configuration…................................................................ 5-19
5.4.5.6 F81866 Super IO Configuration - Serial Port 6
Configuration…................................................................ 5-20
5.4.5.7 F81866 Super IO Configuration - Parallel Port
Configuration…................................................................ 5-21
5.4.6 Advanced – Hardware Monitor ......................................... 5-22
5.4.7 Hardware Monitor – Smart Fan Mode Configuration ........ 5-23
5.4.8 Advanced – F81866 Watchdog Configuration .................. 5-24
5.4.9 Advanced – Network Stack Configuration ........................ 5-25
5.4.10 Advanced – USB Configuration ........................................ 5-27
5.5 Chipset ..................................................................................... 5-28
5.5.1 Chipset – System Agent (SA) Configuration ..................... 5-29
5.5.2 System Agent (SA) Configuration –Memory
Configuration…… ............................................................. 5-30
5.5.3 System Agent (SA) Configuration – Graphics
Configuration… ................................................................. 5-31
5.5.4 System Agent (SA) Configuration – PEG Port

v
Configuration….. ............................................................... 5-33
5.5.5 Chipset – PCH-IO Configuration ....................................... 5-34
5.5.6 PCH-IO Configuration – PCI Express Configuration ........ 5-35
5.6 Security .................................................................................... 5-38
5.7 Boot .......................................................................................... 5-40
5.7.1 Boot – CSM Configuration ................................................ 5-42
5.8 Save & Exit ............................................................................... 5-43
Appendix A System Diagrams .................................................... A-1
SP-S154 System Exploded Diagram (Resistance) ..................................... A-2
SP-S154 Touch Panel & LCD Display Exploded Diagram (Resistance) .. A-3
SP-S154 Box PC Exploded Diagram (Resistance) ..................................... A-5
SP-S154 HDD Module Exploded Diagram (Resistance) ............................ A-7
SP-S154 HDD Tray Exploded Diagram (Resistance) ................................. A-8
SP-S154 System Exploded Diagram (Capacitance) ................................... A-9
SP-S154 Touch Panel & LCD Display Exploded Diagram (Capacitance)
.......................................................................................................................... A-10
SP-S154 Box PC Exploded Diagram (Capacitance) ................................ A-12
SP-S154 HDD Module Exploded Diagram (Capacitance) ....................... A-14
SP-S154 HDD Tray Exploded Diagram (Capacitance) ............................ A-15
SP-S154 Packing Exploded Diagram .......................................................... A-16
SP-S174 System Exploded Diagram (Resistance) ................................... A-17
SP-S174 Touch Panel & LCD Display Exploded Diagram (Resistance)
......................................................................................................................... .A-18
SP-S174 Box PC Exploded Diagram (Resistance) ................................... A-20
SP-S174 HDD Module Exploded Diagram (Resistance) .......................... A-22
SP-S174 HDD Tray Exploded Diagram (Resistance) ............................... A-23
SP-S174 System Exploded Diagram (Capacitance) ................................. A-24
SP-S174 Touch Panel & LCD Display Exploded Diagram (Capacitance)

vi
.......................................................................................................................... A-25
SP-S174 Box PC Exploded Diagram (Capacitance) ................................ A-27
SP-S174 HDD Module Exploded Diagram (Capacitance) ....................... A-29
SP-S174 HDD Tray Exploded Diagram (Capacitance) ............................ A-30
SP-S174 Packing Exploded Diagram .......................................................... A-31
SP-S214 System Exploded Diagram .......................................................... A-32
SP-S214 Touch Panel & LCD Display Exploded Diagram ....................... A-33
SP-S214 LCD Panel Exploded Diagram (1) ............................................... A-34
SP-S214 LCD Panel Exploded Diagram (2) ............................................... A-35
SP-S214 Box PC Exploded Diagram .......................................................... A-36
SP-S214 HDD Module Exploded Diagram ................................................. A-38
SP-S214 HDD Tray Exploded Diagram ...................................................... A-39
SP-S214 Packing Exploded Diagram .......................................................... A-40
Appendix B Technical Summary ................................................ B-1
Main Board Block Diagram ............................................................................. B-2
Interrupt Map ..................................................................................................... B-3
I/O MAP ........................................................................................................... B-15
Memory Map ................................................................................................... B-17
DMA Map ......................................................................................................... B-18
Configuring WatchDog Timer ........................................................................ B-19
Flash BIOS Update ........................................................................................ B-22

vii
Revision History
The revision history of SP-S154 / SP-S174 / SP-S214 User Manual is
described below:
Version No. Revision History Page No. Date
M3
•Revised the Top View diagram of
System Main Board BM-2502. 3-5 2021/03
•Revised the Jumper Settings of
BM-2502RB-**N. 3-6
M2
In the Section 2.4 Safety Precautions,
added the statement: The power
cord with the plug shall be
connected to a socket-outlet with
earthing connections.
2-18 2019/12
M1 Initial Release - 2019/06