protech SG-S151 User manual

USER
MANUAL
SG-S151 / SG-S171 / SG-S211 M2
SG-S151 / SG-S171 /
SG-S211
15” / 17” / 21.5” Intel®Celeron®J3455 /
Atomx7-E3950 Processor
Fanless and All-around IP66/IP69K
Stainless Panel PC

SG-S15 1/SG-S171 /SG-S211
15”/17”/21.5”Intel®Celeron®J3455 /
Atom®x7-E3950 Processor
Fanless and All-around IP66/IP69K
Stainless Panel PC
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Feb. 2020. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’smanual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required totake
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery
only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
CAUTION: The waterproof capability of the device may be
incapable when the screws are loosened.
CAUTION: The O-ring to seal the device may be damaged
during the maintenance process. Qualified engineer is
recommended to make the O-ring replacement to keep the
waterproof capability of the device.
WARNING: Some internal parts of the system may have
high electrical voltage. We strongly recommend that only
qualified engineers are allowed to service and disassemble
the system. If any damages should occur on the system and
are caused by unauthorized servicing, it will not be covered
by the product warranty.

i
Contents
Revision History ............................................................................................. v
1Introduction ......................................................................................... 1-1
1.1 About This Manual .................................................................... 1-2
2Getting Started .................................................................................... 2-1
2.1 Package List.............................................................................. 2-2
2.2 System Overview ...................................................................... 2-3
2.3 SG-S151 System Specifications ............................................... 2-9
2.4 SG-S171 System Specifications ............................................. 2-11
2.5 SG-S211 System Specifications ............................................. 2-13
2.6 Safety Precautions .................................................................. 2-15
3System Configuration......................................................................... 3-1
3.1 External I/O Ports Diagram ....................................................... 3-2
3.1.1 Rear I/O Ports Diagram ..................................................... 3-2
3.2 Jumper & Connector Quick Reference Table............................ 3-3
3.3 Component Locations Of System Main Board.......................... 3-4
3.3.1 Top View of System Main Board ....................................... 3-4
3.3.2 Bottom View of System Main Board.................................. 3-6
3.4 How To Set Jumpers ................................................................. 3-7
3.5 Setting Main Board Connectors and Jumpers .......................... 3-9
3.5.1 COM3 and COM4 PIN9 Definition Selection Guide .......... 3-9
3.5.2 COM Connectors (COM1, COM2) .................................. 3-10
3.5.3 LAN1, LAN2 Ports (LAN1, LAN2).................................... 3-11
3.5.4 Dual USB 3.0 Connectors (USB1) .................................. 3-13
3.5.5 USB 3.0 Connectors (USB2)........................................... 3-13
3.5.6 USB 2.0 Connector (USB3).............................................3-14

ii
3.5.7 Programmable GPIO Pin Header (JDIO1) ......................3-14
3.5.8 I2C Wafer (JI2C1)............................................................ 3-15
3.5.9 MCU FW Rewrite Connector (JMCU1) ........................... 3-15
3.5.10 DC Power Input Connector (PWR2)................................ 3-15
3.5.11 Sysetm Fan Connector (FAN1) ....................................... 3-16
3.5.12 MINI PCI Express Slot (M_PCIE1)..................................3-17
3.5.13 LVDS Connector (LVDS1) ............................................... 3-18
3.5.14 Slide Switch For LVDS Resolution Selection (SW1) ....... 3-19
3.5.15 Front Panel Connector (JFP1) ........................................3-22
3.5.16 HD Audio Connector (AUDIO1).......................................3-22
3.5.17 Panel Inverter Connector (JINV1) ...................................3-23
3.5.18 Serial ATA (SATA) 3.0 Connector (SATA1)...................... 3-23
3.5.19 SATA Power Connector (SATA_PWR1) ..........................3-23
3.5.20 BIOS Reset Connector (JP9) ..........................................3-24
3.5.21 LVDS Backlight Control Selection (JP7)..........................3-24
3.5.22 LVDS VCC Voltage Selection (JP_VDD1)....................... 3-25
3.5.23 Clear CMOS Data Selection (JP4) ..................................3-26
3.6 External M12 Waterproof Connectors..................................... 3-27
3.6.1 USB 2.0 Connectors........................................................ 3-27
3.6.2 Power Button ................................................................... 3-27
3.6.3 LAN1, LAN2 Ports ........................................................... 3-28
3.6.4 COM Connector............................................................... 3-29
3.6.5 DC Power Input Connector ............................................. 3-29
4Software Utilities................................................................................. 4-1
4.1 Introduction................................................................................ 4-2
4.2 Installing Intel®Chipset Software Installation Utility.................. 4-3
4.3 Installing Intel®Trusted Execution Engine Installation Utility .... 4-4

iii
4.4 Installing Microsoft Hotfix kb3211320 and kb3213986 Driver... 4-5
4.5 Installing Graphics Driver Utility ................................................ 4-6
4.6 Installing LAN Driver Utility........................................................ 4-7
4.7 Installing Sound Driver Utility .................................................... 4-8
4.8 Installing Intel®Serial I/O Driver Utility ...................................... 4-9
5BIOS SETUP ........................................................................................ 5-1
5.1 Introduction................................................................................ 5-2
5.2 Accessing Setup Utility.............................................................. 5-4
5.3 Main........................................................................................... 5-7
5.4 Advanced .................................................................................. 5-9
5.4.1 Advanced - ACPI Settings ............................................... 5-10
5.4.2 Advanced – Onboard Device Configuration .................... 5-11
5.4.3 Advanced – Hardware Monitor........................................ 5-12
5.4.4 Advanced – F81964 Watchdog Configuration.................5-13
5.4.5 Advanced – S5 RTC Wake Settings................................ 5-14
5.4.5.1 S5 RTC Wake Settings [Fixed Time]............................... 5-15
5.4.5.2 S5 RTC Wake Settings [Dynamic Time].......................... 5-16
5.4.6 Advanced – CPU Configuration ...................................... 5-17
5.4.6.1 Socket 0 CPU Information...............................................5-18
5.4.6.2 CPU Power Management Configuration .........................5-19
5.4.7 Advanced – F81964 Super IO Configuration .................. 5-20
5.4.8 Advanced – USB Configuration....................................... 5-22
5.4.9 Chipset ............................................................................ 5-23
5.4.9.1 Chipset – North Bridge ....................................................5-24
5.4.9.2 Chipset – South Bridge ................................................... 5-25
5.4.9.3 Chipset – South Bridge – PCI Express Configuration..... 5-26
5.4.9.4 Chipset – South Bridge – SATA Drives ...........................5-30

iv
5.4.9.5 Chipset – South Bridge – Miscellaneous Configuration ..5-31
5.5 Security ................................................................................... 5-32
5.6 Boot ......................................................................................... 5-34
5.7 Save & Exit.............................................................................. 5-36
Appendix A System Diagrams....................................................A-1
SG-S151 System Exploded Diagram .......................................................A-2
SG-S171 System Exploded Diagram .......................................................A-4
SG-S211 System Exploded Diagram .......................................................A-6
VESA Mount Installation Exploded Diagram ............................................A-8
Stand Kit Installation Exploded Diagram ..................................................A-9
SG-S151 Packing Exploded Diagram ....................................................A-10
SG-S171 Packing Exploded Diagram ....................................................A-11
SG-S211 Packing Exploded Diagram.....................................................A-12
Appendix B Technical Summary ................................................B-1
BE-0986 Block Diagram ...........................................................................B-2
Interrupt Map ............................................................................................B-3
I/O MAP ..................................................................................................B-16
Memory Map...........................................................................................B-18
Configuring WatchDog Timer .................................................................B-20
Flash BIOS Update.................................................................................B-22

v
Revision History
The revision history of SG-S151/SG-S171/SG-S211 User Manual is described
below:
Version No.
Revision History
Date
M2 Added user manual information for
SG-S171 and SG-S211.
2020/02/04
M1
Initial Release
2019/07/01

SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 1-1
1 Introduction
This chapter provides the introduction for SG-S151 /
SG-S171 / SG-S211 system as well as the framework of the
user manual.
The following topic is included:
•About This Manual

Chapter 1 Introduction
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 1-2
1.1 About This Manual
Thank you for purchasing our SG-S151 / SG-S171 / SG-S211 system. The SG-S151 /
SG-S171 / SG-S211 is an updated system designed to be comparable with the highest
performance of IBM AT personal computers. The SG-S151 / SG-S171 / SG-S211
provides faster processing speed, greater expandability and can handle more tasks
than before. This manual is designed to assist you how to install and set up the whole
system. It contains 5 chapters and 2 appendixes. Users can configure the system
according to their own needs. This user manual is intended for service personnel with
strong hardware background. It is not intended for general users.
The following section describes the structure of this user manual.
Chapter 1 Introduction
This chapter introduces the framework of this user manual.
Chapter 2 Getting Started
This chapter describes the package contents and system specifications, and illustrates
the physical appearances for SG-S151/SG-S171/SG-S211 system. Read the safety
reminders carefully on how to take care of your system properly.
Chapter 3 System Configuration
This chapter describes the locations and functions of the system motherboard
components. You will learn how to properly configure the connectors and system
configuration jumpers on the motherboard and configure the system to meet your own
needs.
Chapter 4 Software Utilities
This chapter contains helpful information for proper installations of the Intel Chipset
Software Installation Utility, Intel Trusted Execution Engine Driver Utility, Graphics
Driver Utility, LAN Driver Utility, Microsoft Hotfix Driver Utility, Sound Driver
Utility and Intel Serial I/O Driver Utility.
Chapter 5 AMI BIOS Setup
This chapter provides BIOS setup information.
Appendix A System AssemblyDiagrams
This appendix provides the exploded diagrams and part numbers of SG-S151 /
SG-S171 / SG-S211.
Appendix B Technical Summary
This appendix provides the information about the system block diagram, allocation
maps for system resources, Watchdog Timer Configuration and Flash BIOS Update.

SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-1
2 Getting Started
This chapter provides the information for SG-S151 /
SG-S171 / SG-S211 system. It describes how to set up the
system quickly and outlines the system specifications.
The following topics are included:
•Package List
•System Overview
•System Specification
•Safety Precautions
Experienced users can go to Chapter 3 System
Configuration on page 3-1 for a quick start.

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-2
2.1 Package List
If you discover any of the items listed below are damaged or lost, please
contact your local distributor immediately.
Item
Q’ty
SG-S151 / SG-S171 / SG-S211
1
Manual / Driver DVD
1
Quick Guide
1
M12 Power Supply Cable
1
U Stand (optional)
1

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-3
2.2 System Overview
Unit: mm
2.2 System Overview
Unit: mm
Front View Rear View
Top View Bottom View
Left Side View Right Side View
420
335
Antenna
Hole
Antenna
Hole
70
30
SG-S151
385
100
160
130.5
100
207 50

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-4
Quarter View

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-5
SG-S171
Unit: mm
Front View Rear View
Top View Bottom View
Left Side View Right Side View
381
153.5
Antenna
Hole
Antenna
Hole
450
17.5 415
73
207
100
100
M4 screw
(Depth: 8mm)
175
70
30
40

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-6
Quarter View

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-7
SG-S211
Unit: mm
Front View
Rear View
Top View
Bottom View
395
590
20 550
M4 screw
(Depth: 8mm)
100
100
50
267
245
160.5
Antenna
Hole
Antenna
Hole

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-8
weiVediSthgiRweiVediStfeL
Quarter View
70
40
30

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-9
2.3 SG-S151 System Specifications
System
CPU
Type 
Intel®Celeron®J3455

Intel
®
Atom
®
x7 E3950
Memory
Support 
1 x DDR3L 1600/1867MHz SO-DIMM socket
(up to 8GB) (non-ECC)
Operating System

Windows®10 IoT LTSC 2019

Ubuntu 16.04
Enclosure
Stainless SUS304/SUS316
IP Rating

IP66/IP69K
Power Input
DC In 12V/24V
Mounting Support

Wall Mount / VESA 100 / Table Stand
Watchdog
1~255 second Watchdog timer selectable
BIOS

AMI SPI BIOS
Net Weight
7.5kg
Dimensions (W x H x D)

420 x 335 x 70mm
Certifications
FCC / CE
I/O Ports
Power Input

1 x M12 Waterproof Connector with Remote Switch

Supports 12V, 16~24V DC
Serial Port
1 x COM port with M12 waterproof connector
COM1 for RS-232/422/485 selectable under BIOS
LAN

2 x GbE LANs with M12 waterproof connector
LAN 1: Intel®I210IT
LAN 2 : Intel®I210IT

Supports Wake-On-LAN
USB
2 x USB 2.0 with M12 waterproof connectors
Storage

1 x 2.5” SATA III HDD or SSD
Expansion Slot
1 x full-sized Mini PCIe slot (Mini PCIe and USB signals)
Display
LCD
15” TFT LCD (LED) XGA (resolution 1024 x 768),
450 nits
Touch
screen 
15” Projected capacitive touchscreen (USB interface)

15” 5-wire resistive touchscreen (USB interface)

Chapter 2 Getting Started
SG-S151/SG-S171/SG-S211 USER MANUAL
Page: 2-10
Environment
Operating Temp
erature
(with airflow)
HDD: 0°C ~ 40°C (32°F ~ 104°F)
SSD: 0°C ~ 50°C (32°F ~ 122°F)
Wide Temperature SSD:
-20°C ~ 50°C (-4°F ~ 122°F) SSD (for x7-E3950 only)
Storage Temperature

-20°C ~ 80°C (-4°F ~ 176°F)
Humidity
20%~ 90%