protech SP-6110 User manual

USER’S
MANUAL
SP-6110/6112/6118
Intel
®
Atom™ E640T/E680T
10.4”/12.1”/8.4” Fanless Panel PC
With V A/Audio/2LAN
S
P
-
6110/6112/6118
M
1

SP-6110/6112/6118
Intel
®
Atom
™
E640T/E680T
10.4”/12.1”/8.4” Fanless Panel PC
With VGA/Audio/2LAN
COPYRIGHT NOTICE
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
This manual is copyrighted Dec. 2013. You may not reproduce or transmit in any
form or by any means, electronic, or mechanical, including photocopying and
recording.
DISCLAIMER
This user’s manual is meant to assist you in installing and setting up the system. The
information contained in this document is subject to change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not expressly
approve by the party responsible for compliance could void your authority to operate
such equipment.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore
we strongly recommend that qualified engineers can open and disassemble the system. The
LCD and touch screen are easily breakable, please handle them with extra care.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual.................................................................... 1-2
1-2 System Illustratio ....................................................................... 1-3
1-3 System Specifications................................................................. 1-9
1-4 Safety Precautions...................................................................... 1-11
CHAPTER 2 SYSTEM CONFIGURATION
2-1 Jumper & Connector Quick Reference Table............................. 2-2
2-2 Component Locations................................................................ 2-3
2-3 How to Set the Jumpers.............................................................. 2-4
2-4 COM Port Connector……..……………………………............ 2-6
2-5 COM RI & Voltage Selection.................................................... 2-7
2-6 RS232/422/485 (COM2) Selection……..…………………….. 2-8
2-7 COM2 RS485 DIR Control Selection……..………….............. 2-8
2-8 Clear CMOS Data Selection…………………………………... 2-9
2-9 Battery Function Selection......................................................... 2-10
2-10 External Battery Connector...................................................... 2-10
2-11 External Board Connector.......................................................... 2-11
2-12 System Reset Connector............................................................. 2-11
2-13 Power On Switch Connector...................................................... 2-12
2-14 LVDS Connector........................................................................ 2-12
2-15 LVDS Panel Voltage Selection.................................................. 2-13
2-16 VGA Connector......................................................................... 2-13
2-17 Serial ATA Connector…………………………………............ 2-14
2-18 Serial ATA Power Connector…………………………………. 2-14
2-19 Universal Serial Bus Connector …………………………….. 2-14
2-20 LAN Connector………………………………………………... 2-15
2-21 Audio Connector…………….…………………………............ 2-15
2-22 CFast Connector......................................................................... 2-16
2-23 CFast Voltage Selection............................................................. 2-17
2-24 Wide Range Power Mode Setting….......................................... 2-17
2-25 AT/ATX Power Connector……………………………………. 2-18
2-26 Battery Function Selection…………………………………….. 2-18

Contents
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction................................................................................ 3-2
3-2 Intel
®
IOH Driver Utility……………………………………… 3-3
3-3 Intel
®
Chipset Software Installation Utility…..…….................. 3-4
3-4 Graphics Driver Utility............................................................... 3-5
3-5 LAN Driver Utility..................................................................... 3-6
3-6 Sound Driver Utility................................................................... 3-7
3-7 Touchscreen Driver Utility……………………………………. 3-8
CHAPTER 4 AMI BIOS SETUP
4-1 Introduction................................................................................ 4-2
4-2 Entering Setup............................................................................ 4-4
4-3 Main……................................................................................... 4-6
4-4 Advanced…………………….........................…....................... 4-8
4-5 Chipset…………….................................................................... 4-27
4-6 Boot..……………….................................................................. 4-38
4-7 Security………………………………………………………... 4-41
4-8 Save & Exit……………………………………………………. 4-42
APPENDIX A SYSTEM ASSEMBLY
Exploded Diagram for SP-6110 (CPT)/6112/6118 System................... A-2
Exploded Diagram for SP-6110 System……….................................... A-6
Exploded Diagram for SP-6110 CPT System…………………............ A-12
Exploded Diagram for SP-6112 System……….................................... A-18
Exploded Diagram for SP-6118 System……….................................... A-23
APPENDIX B TECHNICAL SUMMARY
Block Diagram...................................................................................... B-2
Interrupt Map......................................................................................... B-3
DMA Channels Map……...................................................................... B-5
I/O Map................................................................................................. B-6
Watchdog Timer Configuration…………..…………………………... B-9
Flash BIOS Update……………………………………………………. B-11

Page:1-1
INTRODUCTION
This chapter gives you the information for SP-6110/6112/6118. It
also outlines the System specification.
Section includes:
About This Manual
System Specifications
Safety Precautions
Experienced users can skip to chapter 2 on page 2-1
for Quick Start.
CHAPTER
1

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-2
1-1. ABOUT THIS MANUAL
Thank you for purchasing our SP-6110/6112/6118 Intel
®
Atom™E640T/E680T
Fanless Panel PC with VGA/Audio/2LAN. SP-6110/6112/6118 provides faster
processing speed, greater expandability and can handle more task than before. This
manual is designed to assist you how to install and set up the system. It contains four
chapters. The user can apply this manual for configuration according to the following
chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the specifications
for this system. The final page of this chapter will indicate how to avoid damaging this
board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the end of this
chapter, you will learn how to set jumper and how to configure this card to meet your
own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the VGA utility,
LAN utility, and Sound utility.
Chapter 4 AMI BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A System Assembly
This appendix gives you the exploded diagrams and part numbers of the SP-
6110/6112/6118.
Appendix B Technical Summary
This appendix gives you the information about the Technical maps, Watchdog-timer
configuration, and Flash BIOS Update.

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-3
1-2. SYSTEM ILLUSTRATION
SP-6110 & SP-6110 CPT
Front View Rear View
277.6
212.8
228.8
160
75
75
202.8
M4*8
(For cutout wall)
48.2
213.2
262
M4*4
(For Visa ARM)
Top View
216
217.5
251.6
M3 (X2)
9
I/O View
216
M3 (X2)
9
LAN1 LAN2 USB VGA COM1 COM2 VCC GND
Unit: mm

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-4
Side View - SP-6110 Side View - SP-6110 CPT
M3 (X2)
9
13
140.6
172.8
10
26
72
23.2
140.6
10
26
77
M3 (X2)
9
172.8
13
23.2
Unit: mm

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-5
SP-6112
Front View Rear View
246
324
250
188.6
230
308
218.5
100
75
48
M4 *10
(For cutout wall)
M4 *4
(For Visa ARM)
Top View
298
9
260
M3 (X3)
216.5
I/O View
260
9
M3 (X3)
LAN1 LAN2 USB VGA COM1 COM2
VCC GND
Unit: mm

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-6
Side View
9 13
23.2
M3 (X2)
140.6
170
10
26
72
Unit: mm

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-7
SP-6118
Front View Rear View
172.4
246.8
184.6
4-R5
130.8
75
M4 * 4
172.2
M3 * 10
228.7
76.2
32.8
75
Top View
217.5
10.4
180
M3 * 2
I/O View
LAN1 LAN2 USB VGA COM1 COM2
VCC GND
Unit: mm

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-8
Side View
162
11.3
6
M3
17.4
Unit: mm

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-9
1-3. SYSTEM SPECIFICATION
System
CPU Support Intel
®
Atom™E640T/E680T processor on board
Chipset Intel
®
EG20T
Memory Support DDR2 1GB on board
Drive Bay 1 x 2.5” SATA HDD
Power Requirement DC-in 9~36V
Wall Mount Type VESA 75
Net Weight SP-6110: 3.5 kg
SP-6112: 4.1 kg
SP-6118: 2.9 kg
Dimension (W x H x D) SP-6110: 277.6 x 228.8 x 71 mm
SP-6112: 324 x 246 x 71 mm
SP-6118: 246.8 x 184.6 x 70 mm
Certificate FCC/CE
I/O Ports
Serial Port 2 ports:
COM1 for RS232, 5V/12V/RI selectable
COM2 is RS232/422/485 selectable
USB 2 x USB 2.0
VGA 1 x VGA
LAN 2 x RJ-45 (10/100/1000 Mbps)
Audio 1 x Line-out
Expansion slot 1 x Mini-PCIe slot
1 x CFast card slot
Display
LCD Panel Size SP-6110: 10.4”
SP-6112: 12.1”
SP-6118: 8.4”
Resolution (Brighness) SP-6110: 800x600 (230nits) / 1024x768 (300nits)
SP-6112: 1024x768(500nits)
SP-6118: 800x600(450nits)
Touch Panel Type 5 Wire Resistive

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-10
Environment
Operation Temp. HDD: 0 ~ 45°C (32 ~ 113°F)
CFast card: -20 ~ 60°C (-4 ~ 140°F)
Storage Temp. -20 ~ 60°C (-4 ~ 140°F)
Humidity 20 ~ 90%

Chapter 1 Introduction
SP-6110/6112/6118 USER ′ S MANUAL
Page: 1-11
1-4. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don’t touch any components of this card when the card is
power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance, when
you connect a jumper or install any cards, a surge of power may damage the
electronic components or the whole system.

Page 2-1
HARDWARE
CONFIGURATION
** QUICK START **
CHAPTER
2
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
Jumper & Connector Quick Reference Table
Component Locations
Configuration and Jumper settings
Connector’s Pin Assignments

Chapter 2 Hardware Configuration
SP-6110/6112/6118 USER ′ S MANUAL
Page: 2-2
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
JUMPER / CONNECTOR NAME
COM Port Connector COM1,COM2
COM RI/Voltage Selection JP6, JP3,
RS232/422/485 (COM2) Selection JP5
COM2 RS485 DIR Control Selection JP4
Clear CMOS Data Selection JP14
Battery Function Selection JBAT1
External Battery Connector BAT1 (Optional)
External Board Connector JP7
System Reset Connector JP8
Power on Switch Connector JP9
LVDS Connector LVDS1
LVDS Panel Voltage Selection JP1
VGA Connector VGA1
Serial ATA Connector SATA1
Serial ATA Power Connector HDD_POWER1
Universal Serial Bus Connector USB1
LAN Connector LAN1, LAN2
Audio Connector JLINE_OUT
CFast Connector JCFAST1
CFast Voltage Selection JP2
Wide Range Power Mode Setting JP12, JP13
AT/ATX Power Selection JP10
Battery Function Selection JBAT1

Chapter 2 Hardware Configuration
SP-6110/6112/6118 USER ′ S MANUAL
Page: 2-3
2-2. COMPONENT LOCATIONS
M/B: SB-8120
SP1
5
10
15
1
6
11
5
9
1
6
5
9
1
6
1 2
1 1
JP10
10
9
2
1
JP4
6
5
2
1
JP5 JP3
6
5
2
1
JP6
1JP9
COM1 COM2
VGA1
USB1LAN1
HDD_POWER1
LAN2 CN_POWER
1
JP2
JP14 1
1
JP12
1
JP13
Battery
1
M_PCIE1
1JP8
1
JLINE_OUT
LPC1
20
101
2
1
1
19
2
20
1
29
2
30
1
6
5
2
1
1
1 3
JP1
1
7
SATA1
FAN1
JP7
JLED1
JVDS1
BAT1
JBAT1
JCFAST1
S1 S7 PC1 PC17
1 4
5 8
SB-8120 Connectors, Jumpers and Components Locations

Chapter 2 Hardware Configuration
SP-6110/6112/6118 USER ′ S MANUAL
Page: 2-4
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of two or three
metal pins with a plastic base mounted on the card, and by using a small plastic "cap",
Also known as the jumper cap (with a metal contact inside), you are able to connect
the pins. So you can set-up your hardware configuration by "open"or "close"pins.
The jumper can be combined into sets that called jumper blocks. When the jumpers
are all in the block, you have to put them together to set up the hardware configuration.
The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3), You can
connect PIN1 & PIN2 to create one setting by shorting. You can either connect PIN2
& PIN3 to create another setting. The same jumper diagrams are applied all through
this manual. The figure below shows what the manual diagrams look and what they
represent.