protech SP-7755 User manual

USER
MANUAL
SP-7755
15” Intel®AtomTM x7-E3950 /
Celeron®N3350 Processor
Fanless and all-around IP66
Panel PC
SP-7755 M1

SP-7755
15” Intel®AtomTM x7-E3950 / Celeron®
N3350 Processor Fanless and all-around IP66
Panel PC
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Nov. 2017. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have
high electrical voltage. We strongly recommend that only
qualified engineers are allowed to service and disassemble
the system. If any damages should occur on the system and
are caused by unauthorized servicing, it will not be covered
by the product warranty.

i
Contents
Revision History .............................................................................................v
1Introduction .........................................................................................1-1
1.1 About This Manual ....................................................................1-2
2Getting Started....................................................................................2-1
2.1 Package List..............................................................................2-2
2.2 System Overview ......................................................................2-3
2.3 System Specifications...............................................................2-5
2.4 Safety Precautions....................................................................2-7
3System Configuration.........................................................................3-1
3.1 External I/O Ports Diagram.......................................................3-2
3.1.1 Rear I/O Ports Diagram.....................................................3-2
3.2 Jumper & Connector Quick Reference Table............................3-3
3.3 Component Locations Of System Main Board..........................3-4
3.3.1 Top View of System Main Board .......................................3-4
3.3.2 Bottom View of System Main Board..................................3-6
3.4 How To Set Jumpers.................................................................3-7
3.5 Setting Main Board Connectors and Jumpers ..........................3-9
3.5.1 COM Connector.................................................................3-9
3.5.2 LAN1, LAN2 Ports...........................................................3-10
3.5.3 Dual USB 3.0 Connectors ...............................................3-12
3.5.4 USB 3.0 Connectors........................................................3-12
3.5.5 USB 2.0 Connectors........................................................3-13
3.5.6 Programmable GPIO Pin Header....................................3-13
3.5.7 I2C Wafer.........................................................................3-14
3.5.8 MCU FW Rewrite Connector...........................................3-14

ii
3.5.9 DC Power Input Connector .............................................3-14
3.5.10 Sysetm Fan Connector....................................................3-15
3.5.11 MINI PCI Express Slot.....................................................3-16
3.5.12 LVDS Connector..............................................................3-17
3.5.13 Slide Switch For LVDS Resolution Selection ..................3-18
3.5.14 Front Panel Connector ....................................................3-21
3.5.15 HD Audio Connector........................................................3-21
3.5.16 Panel Inverter Connector ................................................3-22
3.5.17 Serial ATA (SATA) 3.0 Connector ....................................3-22
3.5.18 SATA Power Connector...................................................3-22
3.5.19 BIOS Reset Connector....................................................3-23
3.5.20 LVDS Backlight Control Selection ...................................3-23
3.5.21 LVDS VCC Voltage Selection..........................................3-24
3.5.22 Clear CMOS Data Selection............................................3-25
3.6 External M12 Waterproof Connector.......................................3-26
3.6.1 USB 3.0 Connectors........................................................3-26
3.6.2 Power Button...................................................................3-26
3.6.3 LAN1, LAN2 Ports...........................................................3-27
3.6.4 COM Connector...............................................................3-28
3.6.5 DC Power Input Connector .............................................3-28
4Software Utilities.................................................................................4-1
4.1 Introduction................................................................................4-2
4.2 Installing Intel®Chipset Software Installation Utility..................4-3
4.2.1 Introduction........................................................................4-3
4.2.2 Intel®Chipset Software Installation Utility .........................4-3
4.3 Intel®Trusted Execution Engine Driver Installation...................4-4
4.3.1 Introduction........................................................................4-4
4.3.2 Installation Instructions for Windows 10............................4-4

iii
4.4 Servicing stack update for Windows 10 Version 1607..............4-5
4.4.1 Introduction........................................................................4-5
4.4.2 Installation Instructions for Windows 10............................4-5
4.5 Installing Graphics Driver Utility................................................4-6
4.6 Installing LAN Driver Utility........................................................4-7
4.7 Installing Sound Driver Utility....................................................4-8
4.8 Installing Intel®Serial I/O Driver Utility......................................4-9
5BIOS SETUP ........................................................................................5-1
5.1 Introduction................................................................................5-2
5.2 Accessing Setup Utility..............................................................5-4
5.3 Main...........................................................................................5-7
5.4 Advanced ..................................................................................5-9
5.4.1 Advanced - ACPI Settings...............................................5-10
5.4.2 Advanced –Onboard Device Configuration....................5-11
5.4.3 Advanced –Hardware monitor........................................5-12
5.4.4 Advanced –F81964 Watchdog Configuration.................5-14
5.4.5 Advanced - S5 RTC Wake Settings ................................5-15
5.4.5.1 S5 RTC Wake Settings [Fixed Time]...............................5-16
5.4.5.2 S5 RTC Wake Settings [Dynamic Time]..........................5-17
5.4.6 Advanced - CPU Configuration .......................................5-18
5.4.6.1 Socket 0 CPU Information...............................................5-19
5.4.6.2 CPU Power Management Configuration.........................5-20
5.4.7 Advanced - F81964 Super IO Configuration...................5-21
5.4.8 Advanced - USB Configuration .......................................5-24
5.4.9 Chipset ............................................................................5-25
5.4.9.1 Chipset –North Bridge.....................................................5-26
5.4.9.2 Chipset –South Bridge ....................................................5-27

iv
5.4.9.3 Chipset –South Bridge- PCI Express Configuration........5-28
5.4.9.4 Chipset –South Bridge- SATA Drives ..............................5-32
5.4.9.5 Chipset –South Bridge- Miscellaneous Configuration.....5-33
5.5 Security ...................................................................................5-34
5.6 Boot.........................................................................................5-36
5.7 Save & Exit..............................................................................5-38
Appendix A System Diagrams....................................................A-1
System Exploded Diagram .............................................................................A-2
Front Panel Module Exploded Diagram........................................................A-3
Heatsink Cover Exploded Diagram................................................................A-4
Stand installation and Wall Mount Exploded Diagram................................A-6
Packing Exploded Diagram.............................................................................A-7
Appendix B Technical Summary................................................B-1
System Block Diagram ....................................................................................B-2
Interrupt Map.....................................................................................................B-3
I/O MAP ...........................................................................................................B-18
Memory Map ...................................................................................................B-20
Configuring WatchDog Timer........................................................................B-22
Flash BIOS Update........................................................................................B-25

v
Revision History
The revision history of SP-7755 User Manual is described below:
Version No.
Revision History
Date
M1
Initial Release
2017/9

SP-7755 USER MANUAL
Page: 1-1
1Introduction
This chapter provides the introduction for the SP-7755
system as well as the framework of the user manual.
The following topic is included:
•About This Manual

Chapter 1 Introduction
SP-7755 USER MANUAL
Page: 1-2
1.1 About This Manual
Thank you for purchasing our SP-7755 system. The SP-7755 is an updated system
designed to be comparable with the highest performance of IBM AT personal
computers. The SP-7755 provides faster processing speed, greater expandability and
can handle more tasks than before. This manual is designed to assist you how to
install and set up the whole system. It contains 5 chapters and 2 appendixes. Users can
configure the system according to their own needs. This user manual is intended for
service personnel with strong hardware background. It is not intended for general
users.
The following section describes the structure of this user manual.
Chapter 1 Introduction
This chapter introduces the framework of this user manual.
Chapter 2 Getting Started
This chapter describes the package contents and system specifications, and illustrates
the physical appearances for the SP-7755 system. Read the safety reminders carefully
on how to take care of your system properly.
Chapter 3 System Configuration
This chapter describes the locations and functions of the system motherboard
components. You will learn how to properly configure the connectors and system
configuration jumpers on the motherboard and configure the system to meet your own
needs.
Chapter 4 Software Utilities
This chapter contains helpful information for proper installations of the Intel Chipset
Software Installation Utility, Intel Trusted Execution Engine Driver Utility, Graphics
Driver Utility, LAN Driver Utility, Microsoft Hotfix Driver Utility and Sound Driver
Utility.
Chapter 5 AMI BIOS Setup
This chapter provides BIOS setup information.
Appendix A System AssemblyDiagrams
This appendix provides the exploded diagrams and part numbers of the SP-7755.
Appendix B Technical Summary
This appendix provides the information about the system block diagram, allocation
maps for system resources, Watchdog Timer Configuration and Flash BIOS Update.