protech SP-7117 User manual

USER’S
MANUAL
SP-7117
Intel
®
D2550 CPU
17” Fanless & Low Power Panel PC
With DVI/2LA /3COM
S
P
-
7117
M
1

SP-7117 Intel
®
D2550
17” Fanless & Low Power Panel PC
With DVI/2LAN/3COM
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
This manual is copyrighted in Dec. 2013. You may not reproduce or transmit in any
form or by any means, electronic, or mechanical, including photocopying and
recording.
DISCLAIMER
This user’s manual is meant to assist you in installing and setting up the system. The
information contained in this document is subject to change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not expressly
approve by the party responsible for compliance could void your authority to operate
such equipment.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore
we strongly recommend that qualified engineers can open and disassemble the system. The
LCD and touch screen are easily breakable, please handle them with extra care.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual.................................................................... 1-2
1-2 System Illustration...................................................................... 1-3
1-3 System Specifications................................................................. 1-5
1-4 Safety Precautions...................................................................... 1-7
CHAPTER 2 SYSTEM CONFIGURATION
2-1 System External I/O Port & Pin Assignment.............................. 2-2
2-2 Mainboard Component Locations & Jumper Settings................ 2-6
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction................................................................................ 3-2
3-2 Intel
®
Chipset Software Installation Utility…..…….................. 3-3
3-3 VGA Driver Utility.................................................................... 3-4
3-4 LAN Driver Utility…………………………………………….. 3-5
3-5 Sound Driver Utility…………………………………………… 3-6
3-6 Touchscreen Driver Utility……………………………………. 3-7
CHAPTER 4 AMI BIOS SETUP
4-1 Introduction................................................................................ 4-2
4-2 Entering Setup............................................................................ 4-4
4-3 Main……................................................................................... 4-7
4-4 Advanced…………………….........................…....................... 4-9
4-5 Chipset…………….................................................................... 4-35
4-6 Boot..……………….................................................................. 4-41
4-7 Security………………………………………………………... 4-44
4-8 Save & Exit……………………………………………………. 4-45
APPENDIX A SYSTEM DIAGRAMS
Exploded Diagram for System with Capacitive Panel........................... A-2
Exploded Diagram for System with Resistive Panel............................. A-10

Contents
Exploded Diagram for HDD.................................................................
A-18
APPENDIX B TECHNICAL SUMMARY
Block Diagram...................................................................................... B-2
Interrupt Map......................................................................................... B-3
DMA Channels Map……...................................................................... B-4
I/O Map................................................................................................. B-5
Watchdog Timer Configuration…………..…………………………... B-8
Flash BIOS Update……………………………………………………. B-10

Page:1-1
INTRODUCTION
This chapter gives you the information for SP-7117. It also outlines
the System specification.
Section includes:
About This Manual
System Specifications
Safety Precautions
Experienced users can skip to chapter 2 on page 2-1
for Quick Start.
CHAPTER
1

Chapter 1 Introduction
SP-7117 USER ′ S MANUAL Page: 1-2
1-1. ABOUT THIS MANUAL
Thank you for purchasing our SP-7117 Intel
®
D2550 17” fanless & low power panel
PC with DVI/2LAN/3COM. SP-7117 provides faster processing speed, greater
expandability and can handle more task than before. This manual is designed to assist
you how to install and set up the system. It contains four chapters. The user can apply
this manual for configuration according to the following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the specifications
for this system. The final page of this chapter will indicate how to avoid damaging this
board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the end of this
chapter, you will learn how to set jumper and how to configure this card to meet your
own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the VGA utility,
LAN utility, and Sound utility.
Chapter 4 BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A System Diagrams
This appendix gives you the exploded diagrams and part numbers of the SP-7117.
Appendix B Technical Summary
This appendix gives you the information about the Technical maps, Watchdog-timer
configuration, and Flash BIOS Update.

Chapter 1 Introduction
SP-7117 USER ′ S MANUAL Page: 1-3
1-2. SYSTEM ILLUSTRATION
Front View Rear View
410.7
375.03
5
M3
M4 (x8)
100 156.57
75
75
100
Top View
Bottom View
Unit: mm

Chapter 1 Introduction
SP-7117 USER ′ S MANUAL Page: 1-4
Side View Quarter View
62
40.5
Unit: mm

Chapter 1 Introduction
SP-7117 USER ′ S MANUAL Page: 1-5
1-3. SYSTEM SPECIFICATION
System
CPU Support Intel
®
D2550 (1.86GHz, 1M cache)
Chipset Intel
®
NM10
OS Support Microsoft Windows 7
Memory Support 1 x DDR3 SO-DIMM socket (1067 MHz, up to 4GB)
Watchdog 1~255s Watchdog timer
Drive Bay 1x 2.5” SATA HDD
Power Supply DC-in 9~36V
Mounting Type VESA 75/100
IP65 Front panel only
System Weight 5.95 kg
Dimension (W x H x D) 410.7 x 374.6 x 62 mm (16.16” x 14.75” x 2.44”)
Certificate CE/FCC
I/O Ports
Serial Port 3 ports, RI/5V/12V selectable:
COM1 for RS-232
COM2/3 for RS-232/422/485
USB 4 x USB 2.0
LAN 2 x LAN (RJ-45, 10/100/1000 Mbps)
DVI 1 x DVI-I
Audio High Definition:
1 x Line-out
1 x MIC-in
Expansion slot 1 x Mini-PCIe slot
1 x CFast card slot
Display
LCD Panel 17” TFT LCD (LED)
Resolution (Brighness) 1280 x 1024

Chapter 1 Introduction
SP-7117 USER ′ S MANUAL Page: 1-6
Touchscreen 5-wire bezel-free resistive or projected-capacitive
Environment
Operation Temp. HDD: 0 ~ 45°C (32 ~ 113°F)
CFast card: 0 ~ 55°C (32 ~ 131°F)
Storage Temp. -20 ~ 60°C (-4 ~ 140°F)
Humidity Operating: 20 ~ 90%
Storage: 20~95%

Chapter 1 Introduction
SP-7117 USER ′ S MANUAL Page: 1-7
1-4. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don’t touch any components of this card when the card is
power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance, when
you connect a jumper or install any cards, a surge of power may damage the
electronic components or the whole system.

Page 2-1
HARDWARE
CONFIGURATION
** QUICK START **
CHAPTER
2
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
Jumper & Connector Quick Reference Table
Component Locations
Configuration and Jumper settings
Connector’s Pin Assignments

Chapter 2 Hardware Configuration
SP-7117 USER ′ S MANUAL Page: 2-2
2-1. SYSTEM EXTERNAL I/O PORT & PIN ASSIGNMENT
I/O View
DC IN DVI
LAN1
Line-out
MIC
LAN2 COM1
Power switch
COM2 COM3
USB

Chapter 2 Hardware Configuration
SP-7117 USER ′ S MANUAL Page: 2-3
2-1-1. DC IN Port
DC IN: DC Power-In Port
PIN ASSIGNMENT PIN ASSIGNMENT
1 GND 3 VCC24_SB_VIN
2 GND 4 VCC24_SB_VIN
2-1-2. Audio Jack
Line-Out: Audio Line-Out Jack
Connected from Audio1 connector.
Refer to Audio1 pin assignment in section Mainboard
Components Locations & Jumper Settings.
2-1-3. COM Ports
COM1, COM2, COM3: COM Ports
PIN ASSIGNMENT PIN ASSIGNMENT
1 DCD_C 6 DSR_C
2 RX_C 7 RTS_C
3 TX_C 8 CTS_C
4 DTR_C 9 RI_SEL
5 GND
Note: COM3 port is connected from a connector on
board. Refer to the section COM connector.
34
12
DC IN
Line-Out
5
1
9
6
COM1/
COM2/
COM3/

Chapter 2 Hardware Configuration
SP-7117 USER ′ S MANUAL Page: 2-4
2-1-4. DVI Port
DVI: DVI-I Port
PIN ASSIGNMENT PIN ASSIGNMENT
1 TMDS_2- 16 HPD
2 TMDS_2+ 17 TMDS_0-
3 GND 18 TMDS0+
4 NC 19 GND
5 NC 20 NC
6 DDC_CLK 21 NC
7 DDC_DATA 22 GND
8 VSYNC 23 TMDS_CLK+
9 TMDS_1- 24 TMDS_CLK-
10 TMDS_1+ C1 RED
11 GND C2 GREEN
12 NC C3 BLUE
13 NC C4 HSYNC
14 5V C5 GND
15 GND C6 GND
1
9
17
C1 C2
C3 C5 C4
DVI1

Chapter 2 Hardware Configuration
SP-7117 USER ′ S MANUAL Page: 2-5
2-1-5. LAN Port
LAN1, LAN2: RJ45 LAN Ports
PIN ASSIGNMENT PIN ASSIGNMENT
1 MDI0_DP 5 MDI2_DP
2 MDI0_DN 6 MDI2_DN
3 MDI1_DP 7 MDI3_DP
4 MDI1_DN 8 MDI3_DN
LAN LED Indicator:
Left Side LED
Green Color On 10/100 LAN Speed Indicator
Orange Color On Giga LAN Speed Indicator
Off No LAN switch/hub connected.
Right Side LED
Yellow Color Blinking LAN Message Active
Off No LAN Message Active
2-1-6. USB Ports
USB Ports: Two USB Double Stack Connectors
PIN ASSIGNMENT PIN ASSIGNMENT
1 +5V 5 +5V
2 DN 6 DN
3 DP 7 DP
4 GND 8 GND
Green Yellow
8 1
LAN1/
LAN2/
41
85
USB

Chapter 2 Hardware Configuration
SP-7117 USER ′ S MANUAL Page: 2-6
2-2. MAINBOARD COMPONENT LOCATIONS & JUMPER
SETTINGS
M/B: SB-6310
SP1
Battery
1
2
9
10
COM3
COM4
JTP1
PWR_BTN1
PWR_LED1
RST_BTN1
SIO
10 5
16
JP8
AUDIO1
5
6
1
2
9 10
1 2
JP12
5
6
1
2
JP13
JP14 JP15
COM2
COM1
JUSB3 JUSB2 LAN2 LAN1 JDVI1 PWR_IN1
6 5
2 1
J1
JHDD_LED1
1 2
7 8
JP_VDD1
1 2
5 6
HDD_POWER1
SATA1
1
7
4
1
JP11
JP16
JP17
3
1
3
1
JP_PWM1
JP10 SPK_L_OUT1
SPK_R_OUT1
1
3
JP9
JP7
JP1 JP2 JP3 JP4
1111
JP_BLEN1
CPUFAN1
INV1
DIMM1
JP_BRCT
R1
Intel
®
NM10 Intel
®
D2550
M_PCIE1
JTAG1
OSD_CTRL1
1 15 17 51
2 16 18 52
J2
JP5
9
102
1
1
12
18
LVDS1
3029
1 2
JUSB6
JUSB7
15
1
3
1
2
71
72
73
74
203
204
3
1
3
1
1
1
1
5
31
1
1
10
5
6
9
15
1
19
210
1
2
1
2
1
2
9
1
12
12
JP6
5
6
1
2
SP-7117 Connectors, Jumpers and Component Locations

Chapter 2 Hardware Configuration
SP-7117 USER ′ S MANUAL Page: 2-7
JCFAST1
S1
S7
PC1
PC17
SP-7117 Component Location

Chapter 2 Hardware Configuration
SP-7117 USER ′ S MANUAL Page: 2-8
2-2-1. Jumpers & Connectors Quick Reference Table
JUMPER/CONNECTOR NAME
COM Ports RI & Voltage Selection JP12, JP13, JP8, JP6
COM2 & COM3 RS-232/422/485 JP15, JP17
COM2 & COM3 RS-485 DIR Control
Selection
JP14, JP16
COM Connector COM3, COM4
USB Connector JUSB6, JUSB7
CFAST Voltage Selection JP11
Low Pin Count Connector J2
SPI Connector J1
SATA Connector SATA1
Mini-PCIe Connector M_PCIE1
Clear CMOS Data Selection JP5
CPLD Connector JTAG1
LCD Panel Resolution Selection JP1, JP2, JP3, JP4
LCD Panel Brightness Control Selection JP_BRCTR1
LCD Panel Backlight Selection JP_BLEN1, JP_PWM1
Touch Panel Connector JTP1
LED Backlight Connector INV1
OSD Function Connector OSD_CTRL1
LVDS Connector LVDS1
LVDS Voltage Selection JP_VDD1
Pull-In Mode Selection JP7
Run Pin Selection JP9
Power Mode Selection JP10
Power LED Connector PWR_LED1
Power Button Connector PWR_BTN1
Reset Button Connector RST_BTN1
HDD Power Connector HDD_POWER1
HDD LED Connector JHDD_LED1
Fan Connector CPUFAN1
Audio Connector Audio1, SPK_L_OUT1, SPK_R_OUT1