Regency Legacy LCTRT14452 User manual

Parts: Quantity will vary with model.
A: End Leg B: Center Leg
Quantity: 2
Quantity: 2
H: Thumb
Screws
I: Flat
Bracket
D: Stringer
F: Cord Holder
G: EClip Bracket
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid scratching the parts.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Keep all hardware parts and packaging out of reach of children.
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
C: Round End
Legacy Modular Conference Table • INSTRUCTIONS
(LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652,
LCTRT24052, LCTRT26452, LCTRT28852)
Organize your parts. You may need a rubber mallet.
E: Center Piece
Hardware: Quantity will vary with model.
J: DPEL

STEP 2: Attach Stringer(D) to Center Leg(B) by lining up Eclip with it’s corresponding hole, and sliding down into place.
Please Note: Center Legs (B) have EClip attachment holes on both sides.
D
BA
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
Figure 1
Legacy Modular Conference Table • INSTRUCTIONS
(LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652,
LCTRT24052, LCTRT26452, LCTRT28852)
Organize your parts. You may need a rubber mallet.
D
A
STEP 1: Attach Stringer(A) to one of the End Legs(A) by lining up the Eclip with its corresponding holes, and sliding down
into place (see gure 1.) Please Note: End Legs (A) have EClip attachment holes on one side only.

STEP 4: Attach EClip Brackets(G) into precut slots in the center of each Stringer(D). Line up Lockdowels with available
holes, and press down to snap into place.
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
STEP 3: Attach next Stringer(D) to other side of Center Leg(B) by lining up Eclip with corresponding holes, and sliding down
into place.
STEP 4: Attach next End Leg(A) or Center Leg(B) (Will vary depending on model of table.) Attach by lining up holes with
corresponding Eclip, and slilding down into place.
A
D
D
A
B
G
D D
G
Please Note: Depending on your model of table, you may need to repeat STEP 3 &STEP 4 until you have used all Center
Legs(B) , and Stringers(D) provided.
Legacy Modular Conference Table • INSTRUCTIONS
(LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652,
LCTRT24052, LCTRT26452, LCTRT28852)
Organize your parts. You may need a rubber mallet.

STEP 5: Attach Center Piece(E) onto assembled base by lining up pre-drilled holes on the bottom with the EClips on
each Eclip Bracket(G) and Center Leg(B) and sliding into place. Please Note: Repeat this step until you have used all
included Center Pieces(E).
STEP 6: Attach Round Ends(C) to assembled product by lining up pre-drilled holes on bottom with the EClips on both the
End Legs(A) and EClip Brackets(G) and then sliding Round Ends(C) into place.
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
E
B
GG
A A
C
A
C
A
EE
Legacy Modular Conference Table • INSTRUCTIONS
(LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652,
LCTRT24052, LCTRT26452, LCTRT28852)
Organize your parts. You may need a rubber mallet.

STEP 7A: From underneath the table, lock all available Sash Locks on the Center Pieces(E) (see gure 1).
STEP 7B: From underneath the table, attach all available Flat Brackets(E) by using Thumb Screws(E) (see gure 2).
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
I
E
Figure 2.Figure 1.
OPTIONAL STEP 8: Insert DPEL(J) using provided screws.
OPTIONAL STEP 9: Attach Cord Holder(F) underneath table onto cam lock side of Stringer(D) with provided double
sided tape.
D
F
Legacy Modular Conference Table • INSTRUCTIONS
(LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652,
LCTRT24052, LCTRT26452, LCTRT28852)
Organize your parts. You may need a rubber mallet.