Regency 72” STORAGE CABINET LSC7236 User manual

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
IMPORTANT NOTICE:
● Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
● Check to be sure that you have all parts and hardware.
● Remove all wrapping materials, including staples & packing straps before you start to assemble.
● Do not tighten all screws/bolts until completely assembled.
● Keep all hardware parts out of reach of children.
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS
Organize your parts and hardware. You will need a Phillips head and at head screw driver and rubber mallet.
Hardware :
A: Mounting Bracket(8) • B: Inner Hinge(4) • C: Outer Hinge(4) D: Lock Lip(2) • E: Small Screw(4)
F: Cam Pins(20) • G: Medium Screws(56) • H: Shelf Pins(16) • I: Adjustable Glides(6) J: Large Screws(8)
K: Door Handles(4) • L: Keys(2)
ABCDEFGH
Parts :
M: Back • N: Front support • O: Middle Support• P: Bottom • Q: Left Side • R: Right Side • S: Shelves (4)
T: Top • U: Right side Door(2) • V: Left side Door(2) • W: Center wall
T
SQ
P
O
NU
IJKL
M
V
Figure 1: To open Cam, point
arrow toward Cam Pin hole.
To lock Cam, turn clockwise.
R
W

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
IMPORTANT NOTICE:
● Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
● Check to be sure that you have all parts and hardware.
● Remove all wrapping materials, including staples & packing straps before you start to assemble.
● Do not tighten all screws/bolts until completely assembled.
● Keep all hardware parts out of reach of children.
STEP 1 : Attach front
support(N) to middle
support(O) by inserting
the dowel rod on the
end of(O) into
the middle of(N).
STEP 2 : Connect dowel rods on
Front support(N)
and Middle support(O)
to the bottom(P).
STEP 3 : Insert 2 cam pins(F) into back(M)
and connect(M) to bottom(P) by inserting and
locking cams (Fig1). STEP 4 : Insert 4 cam pins(F) into both
left(Q) and right(R) side.
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS
N
O
N
O
P
Cam locks on(P) facing (N)
F
F
MM
P
R
F
F F
F
F
F
F
Q
STEP 5 : Attach left(Q) and right(R) side to
back(M) and bottom(P) by inserting and lock-
ing cams located on (Fig1)
QR
M
P

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
IMPORTANT NOTICE:
● Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
● Check to be sure that you have all parts and hardware.
● Remove all wrapping materials, including staples & packing straps before you start to assemble.
● Do not tighten all screws/bolts until completely assembled.
● Keep all hardware parts out of reach of children.
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS
STEP 6 : Screw in 6 adjustable glides(I) in
the locations shown below with 4 medium
screws(G) each.
P
F
V
STEP 7 : Place 2 cam pins(F) in bottom(P)
and attach center wall(W) with banded edge
facing out by inserting and locking cams (Fig1).
P
F
W
I
I
I
I
I
IF
STEP 8a : Screw 8 cam pins(F) into top(T). Use 2 small screws(E) each to attach locking lips(D).
STEP 8b : Attach top by inserting and locking cams (Fig1).
F
FF F
F
FF
F
DD
D
E E
STEP 9 : Attach 8 mounting brackets(A) to the pre drilled holes in the sides(Q,R) and center wall(W) with
the open end facing out. Mount the inner hinges to(W) and outer hinges to(Q,R) by sliding the bolt on the
underside of the hinges into the open end of the mount while sliding the screw on the mount into the open
end of the hinge. Tighten the screw on the back to lock into place.
A/B A/B
A/B A/B A/C
A/C
A/C
A/C
D
E E
T

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
IMPORTANT NOTICE:
● Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
● Check to be sure that you have all parts and hardware.
● Remove all wrapping materials, including staples & packing straps before you start to assemble.
● Do not tighten all screws/bolts until completely assembled.
● Keep all hardware parts out of reach of children.
STEP 10 : Mount the right side doors(U) to the sides(Q,R) with 2 medium screws(G) each hinge. Also
mount the left side doors(V) to the center wall(W) in the same manner.
G
G
STEP 10a : Use 2 Large screws(J)
per handle(K) and attach (K) to
doors(T,U) using the 2 pre drilled
holes per door. J
J
K
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS