Regency ONRT3624 User manual

Organize your parts and hardware. You will need (2) people, a Phillips head screwdriver and rubber mallet.
Parts :
TT-E: Return Top
(35” x 23” x 1”)
Quantity: 1
MP-A: Return Modesty
(34” x 12” x 1”)
Quantity: 1
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Do not tighten all screws/bolts until completely assembled.
Keep all hardware parts out of reach of children.
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
LG-F
TT-E
MP-A
LG-E
LG-D
LG-D: Leg
(24.5” x 23.5” x 1”)
Quantity: 1
LG-E: Leg Foot Bracket
(23.5”D)
Quantity: 1
LG-F: Leg Top Bracket
(23.5”D)
Quantity: 1
Cam Lock Assembly:
To open Cam, point arrow
toward Cam Pin hole. To
lock Cam, turn clockwise.
Figure 1:
36” Return Shell • ONRT3624 • INSTRUCTIONS
CARTONS: TT3624, MP3512, LG2824
36” Return Shell
Page 1

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
Hardware :
F: Flat Bracket
Quantity: 4
G: Allen Key
Quantity: 1
H: Wood Cam Pins
Quantity: 2
L: 3/4” Short Bolts
(19mm)
Quantity: 22
I: Glides
Quantity: 2
J: Insert Covers
Quantity: 4
M: Locking Screws
Quantity: 2
Locking Screws
K: Cam Caps
Quantity: 2
N: 3” Screw/Washers
(76mm)
Quantity: 5
STEP 1 : HARDWARE PLACEMENT ON RETURN LEG(LG-D) DEPENDS ON LEFT RETURN & RIGHT RETURN ORIENTATIONS.
PLEASE EXAMINE CAREFULLY.
STEP 1A : Insert 2 Locking Screws(M) and 2 Wood Cam Pins(H) into Return Leg(LG-D) as shown below.
MM
H
H
N
N
LG-D
MM
H
H
LG-D
Left Return
NOTE : PRODUCT IS REVERSIBLE.
SOME STEPS INCLUDE BOTH RIGHT AND LEFT ORIENTATIONS.
Please examine all parts before assembly. Hardware placement is critical.
O: Corner Bracket
Quantity: 2
P: 3/4” Wood Screws
(19mm)
Quantity: 12
36” Return Shell • ONRT3624 • INSTRUCTIONS
CARTONS: TT3624, MP3512, LG2824
36” Return Shell
Page 2

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
STEP 3 : Attach Return Leg(LG-D) to Return Top(TT-E)
using 6 Short Bolts(L).
TT-E
STEP 4 : Attach Return Modesty(MP-A) to Return
Leg(LG-D) by inserting and locking cam pins (Figure 1).
NOTE: Cam Locks face the interior of the Return. Be sure to
support opposite end of Modesty.
L L
LG-D LG-D
MP-A
STEP 2 : Attach Leg Foot Bracket(LG-E) to the Return Leg(LG-D) using 3 Screw/Washers(N). Then, insert 2 Glides(I) into
Leg Foot Bracket(LG-E). Also, attach Leg Top Bracket(LG-F) to Return Leg(LG-D) by using Locking Screws(M) already
attached, into the slide locking holes on Leg Top Bracket(LG-F) and slide into place. Finish attaching Leg Top Bracket(LG-F) by
inserting 2 Screw/Washers(N) into Leg(C).
II
N
NN
Left Return Right Return II
N
NN
LG-F
LG-E
LG-D
LG-F
NOTE: Supports
face interior side.
LG-E
LG-D
36” Return Shell • ONRT3624 • INSTRUCTIONS
CARTONS: TT3624, MP3512, LG2824
36” Return Shell
Page 3

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
STEP 5 : Attach Return Modesty(MP-A) to Desk Leg with 2 Flat Brackets(F) using 4 Short Bolts(L) per bracket. Then, attach
Return Top(TT-E) to Desk Top with 2 Flat Brackets(F) using 4 Short Bolts(L) per bracket. Finish by concealing Cam Locks
with Cam Caps(K) & Insert Covers(J).
TT-E
MP-A
STEP 6 : For additional stability, attach Corner Brackets(O) to Leg(LG-D) and the Modesty(MP-A) with 6 Wood Screws(P) per
Corner Bracket.
36” Return Shell • ONRT3624 • INSTRUCTIONS
CARTONS: TT3624, MP3512, LG2824
36” Return Shell
Page 4