Regency LDS4224 User manual

Parts:
Quantity: 1
C: Desk Side
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid scratching the parts.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Keep all hardware parts and packaging out of reach of children.
Any problems or questions call Regency O󰀩ce Furniture at 1-866-816-9822 or at [email protected]
B: Desk Front
Legacy Desk Shell • LDS4224, LDS6030, LDS6630, LDS7124, LDS7135, LDSBF7135 • INSTRUCTIONS
Organize your parts. You may need a rubber mallet.
Quantity: 1
Quantity: 2
A: Desk Top
A
B
C
C

STEP 1: Attach Desk Front (B) to one of the Desk Sides
(C) by lining up the Eclip with its corresponding holes,
and sliding into place (see gure 1).
STEP 2: Attach the remaining Desk Side (C) to the Desk
Front (B) by lining up the Eclip with its corresponding
holes, and sliding into place .
STEP 3A: Remove Thumb Screw from Desk Top (A) before assembly. Next, attach Desk Top (A) to the assembled base
by lining up the Eclip with its corresponding holes, and sliding into place (see gure 2.)
Any problems or questions call Regency O󰀩ce Furniture at 1-866-816-9822 or at [email protected]
Figure 1
Figure 2
Figure 3
B
B
C
C
C
C B
A
A
STEP 3B: Finally, place Thumb Screw into the front angle bracket
connecting the Desk Top (A) to the Desk Front (B) (see gure 3.)
Legacy Desk Shell • LDS4224, LDS6030, LDS6630, LDS7124, LDS7135, LDSBF7135 • INSTRUCTIONS
Organize your parts. You may need a rubber mallet.

Parts and hardware:
A: Pedestal
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid scratching the parts.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Keep all hardware parts and packaging out of reach of children.
Any problems or questions call Regency O󰀩ce Furniture at 1-866-816-9822 or at [email protected]
Organize your parts and hardware
Pedestals • LPBF22 • LPBBF22 • LPFF22 • INSTRUCTIONS
LPBF22 shown
B: Thumbscrew
D: Screws
Quantity: 4
Quantity: 12
STEP 1 : Remove all drawers from pedestal.
To remove Box drawers: Fully extend drawer and gently roll
drawer up and out.
To remove File drawers: Simultaneously press down lever
on right side of drawer and pull up lever on left side of
drawer and slide drawer straight out of the track
PULL UP
STEP 2 : Thread Thumbscrews (B) through holes. Align
Pedestal (A) with pre-drilled holes on the underside of
desktop and attach. Do not tighten Thumbscrews (B)
until all four are in place and pedestal is aligned ush with
side of desk.
PUSH DOWN
DESK TOP
Please note: Pedestal Attachment is easiest
when desk shell is still upside down.
B
LPBF22 MODEL ONLY : Attach Corner Brackets (C)
to the underside of Pedestal (A) and side of desk with
Screws (D.)
LPBBF22 AND LPFF22 MODELS ONLY: Adjust leveling
glides to bring Pedestal (A) level with desk shell. With the
desk upright and drawers out, use screwdriver to rotate
glide through the bottom of Pedestal (A) until level.
C: Corner Bracket
Quantity: 2
C & D
A
DESK SHELL
FRONT
Note: Do not replace drawers while desk is upside down
Rotate clockwise to raise glides and
counter-clockwise to lower glides