Reison nordiska 10-390 User manual

USERS MANUAL
ARM & HAND SURGERY
TABLE 10-390
GMDN 35393
PID 51389
10-390 Edit. 1 Page 1(4)

INTRODUCTION
The Arm & Hand Surgery table is made for operation of arms and hands. It is designed to be hooked
on a standard European accessory rail (25x10mm) and can be used with or without a supporting leg.
The plate is made from reinforced PFP (Phenol plastic) with very good x-ray facilities, making it
easy to operate with use of fluoroscopy. If used with microscope, it is recommended to use the
supporting leg.
ABOUT USERS MANUAL
This user manual is for clinical personnel, service personnel and others, who need the knowledge
about and understanding of how the arm & hand surgery table works and how it can be used.
Read user manual carefully before use of the equipment.
Always follow the instructions in user manual.
Always keep user manual close to the equipment.
INSTALLATION
At the unpacking, check that there are no damages on the equipment. Also check that all parts are
received according to the delivery note.
The packing material consists of cardboard and plastic, which all can be recycled.
IMPORTANT SAFETY DIRECTIONS
When applying the arm & hand surgery table to an operating table, the responsible personnel
must be sure of that the both clamps are properly hooked on and locked to the accessory rail
of the operating table.
When a supporting leg is to be used, the person who apply the leg must be sure of that the
supporting leg is properly locked to the arm & hand surgery table.
A functional control of the clamp locking system must be done every day before use. Also
check for any kind of damage that can make the use hazardous.
The table is designed for a Safe Working Load of 40kg, corresponding to a patient weight of
300kg. To keep the safety factor, according to the European standards EN 60601 and EN
60601-2-46, the Safe Working Load must not be exceeded.
CARE AND MAINTENANCE
Be aware of, that service and all kind of repair only must be done by for this purpose educated
personnel. Changing of the construction without a written permission from the manufacturer is
strictly forbidden.
Cleaning Clean with soap and tempered water. If necessary, use antiseptic detergents with PH
between 6 –8. Do not use alcohol or strong acids.
Control Check daily for any kind of damages and that there are no loose parts on the arm &
hand surgery table. Check the clamps and supporting leg locking function.
Annual service
Once a year the arm & hand surgery shall be table carefully cleaned, moving parts shall
be lubricated with thin grease and the locking functions carefully tested.
10-390 Edit. 1 Page 2(4)

GENERAL DESCRIPTION
SPARE PARTS
10-390 Edit. 1 Page 3(4)
The arm & hand surgery table can be adjusted in
height to meet different thicknesses of operating
table mattresses. To adjust, turn the locking levers
of the clamps anticlockwise, set to desired height
and lock by turning the levers clockwise.
Clamp locking lever
for height ajustm.
Knob for lock of
the supporting leg
Levers for locking of the
clamps to the accessory rail
Lever for height adjustment
of the supporting leg
The arm & hand surgery table is equipped with
“hook on” clamps, which locks to the accessory
rail by turning the lock levers to horizontal
position, to the left or to the right. A slight “click”
appears when the levers are in correct position.
The supporting leg can be mounted on the
right side or on the left side and is locked in
position by the turning the knob clockwise.

TECHNICAL SPECIFICATIONS
Length 81,5cm
Width 52cm
Height 70-115cm
Weight 13 kg
Safe Working Load 40kg
Max patient weight 300kg
Box 240 Eriksbergsvägen 32 A
734 25 Hallstahammar
Sweden
Phone: [phone] Fax: [phone]
E-mail: [email protected]e
www.reison.se
10-390 Edit.1 Page 4(4)
1. Frame weld assy. 10056 1pc.
2. Plate 10045 1pc.
3. Blind rivet AS 4,8x12-F 12pcs.
4. Knob VCT.43 p-M8x16 soft 2pcs.
5. Mattress 10-391 1pc.
6. Strap 10915 2pcs.
7. Strap lock HPCB 325 10916 4pcs.
8. Washer 10004 2pcs.
9. Screw MF6S M6x12 A2 2pcs.
10. Clamp body 10031 2pcs.
11. Supporting leg assy 11041 1pc.
12. Adjustable lock lever 6-593-65 2pcs.
13. Guide 10053 2pcs.
14. Spring 10013 2pcs.
15. Pressure pin 10012 2pcs.
16. Plunger 10711 2pcs.
17. Lock lever 10014 2pcs.
18. Ball K20 M8 S 2pcs.
19. Eccentric 11165 2pcs.
20. Shaft 10009 2pcs.
21. Screw MC6S M6x35 FZ 4pcs.