Reison nordiska 10-396 User manual

USERS MANUAL
ARM & HAND SURGERY
TABLE 10-396
GMDN 35393
PID 80219
10-396 Edit.2 page1 (4)

INTRODUCTION
The arm & hand surgery table is made for positioning and operation of arms and hands. It is
designed to be hooked on to the accessory rail on an op.table and can be used with or without
supporting leg.
ABOUT USERS MANUAL
This user manual is for clinical personnel who need the knowledge and understanding about how
the arm & hand surgery table works and should be used.
Read user manual carefully before using the equipment.
Always follow the instructions in user manual.
Keep user manual in range of the equipment.
IMPORTANT SECURITY INSTRUCTIONS
A function control must always be done before using the equipment.
Service and preventing maintenance shall be done by authorized personnel and according
to issued intervals.
The arm & hand surgery table is designed for a Safe Working Load of 20 kilograms evenly
applied. To keep the safety factor according to European Standard EN 60601-1 and EN
60601-2-46, the Safe Working Load should not be exceeded. 20kg Safe Working Load is
corresponding to a patient weight of 270kg.
The personnel responsible for adjusting the arm & hand surgery table must be sure of that
there are no human parts in the risk area during adjusting.
To avoid injuries on hands and fingers, the arm & hand surgery table shall be supported
while loosen the locking levers for height adjustment.
GENERAL DESCRIPTION
10-396 Edit.2 Page 2 (4)
The table shall be hooked to the accessory
rail and be locked by turning the locking
levers of the clamps to the left or to the
right.
Risk area
Height adjustment performs by loosen the
locking levers anticlockwise, increase or decrease
the height and lock by tighten the levers
clockwise.
Lock knob
Lever
The supporting leg can be assembled on the right
or the left side and be locked by the knob. Height
adjustment performs by folding down the lever on
the leg, adjust to desired position and lock by
folding up the lever.
Maximum load 20 kg evenly applied

CARE AND MAINTENANCE
Be aware of, that mounting, adjustments and all kind of repair, only can be done of for this
purpose educated personnel. Be also aware of, that changing of any part in the construction
without permission from the manufacturer is strictly forbidden.
Cleaning
Clean with soap and tempered water. Use alcohol as supplement if needed. Only use soft cloth.
Control
Check daily for any kind of damages. Also check, that there is no loose parts on the arm & hand
surgery table. Check the locking function on the support leg and that the clamps locks properly to
the accessory rail.
Annual service
Once a year the arm & hand surgery table shall be carefully cleaned up, moving parts in the
clamps shall be greased and all locking functions shall be tested and, if necessary, adjusted.
SPARE PARTS LIST
10-396 Edit 2 Page 3 (4)

TECHNICAL SPECIFICATION
Length 820 mm
Width 525 mm
Height 720 –1150 mm
Weight incl. support leg 5,6 kg
Safe Working Load 20kg
Max patient weight 270kg
Box 240 Eriksbergsvägen 32 A
734 25 Hallstahammar
Sweden
Phone: [phone] Fax: [phone]
E-mail: [email protected]e
www.reison.se
10-396 Edit. 2 Page 4 (4)
1. Plate 10912 1pc.
2. Guide 10687 2pcs.
3.
4. Mattress 10-397 11006 1pc.
5. Mattress fixation 11364 4pcs.
6. Washer BRB 10,5x22x2 A2 2pcs.
7. Post 10968 2pcs.
8. Stay 10966 1pc.
9. Clamp body 10031 2pcs.
10. Screw MC6S M6x40 FZ 4pcs.
11. Washer 10004 2pcs.
12. Screw MF6S M6x12 A2 2pcs.
13. Support leg assembly 10998 1pc.
14. Screw MF6S M6x16 A2 4pcs.
15. Knob VCT.43-p M8x16 soft 2pcs.
16. Adjustable lock lever 6-593-65 2pcs.
17. Guide 10053 2pcs.
18. Spring 10013 2pcs.
19. Shaft 10009 2pcs.
20. Pressure pin 10012 2pcs.
21. Plunger 10711 2pcs.
22. Eccentric 11165 2pcs.
23. Lock lever 10014 2pcs.
24. Ball K20 M8 S 2pcs.