Roger MCT88M-IO User manual

MCT88M-IO Installation Manual 2019-10-02
1/2
Roger Access Control System
MCT88M-IO Installation Manual
Firmware version: 1.0.2.97 and newer
Document version: Rev. F
This document contains minimum information that is necessary for initial setup
and installation of the device. The detailed description of configuration
parameters and functionalities is specified in respective Operating manual
available at www.roger.pl.
INTRODUCTION
The terminal is designed to operate in RACS 5 system as peripheral device
connected to RS485 bus of MC16 access controller. Alternatively the device can
communicate with virtual controller via Ethernet (LAN) and operate as PoS
terminal or assets management terminal. Factory new terminal is configured with
default settings including ID=100 address. Before connecting to MC16 controller,
the device should be assigned with unoccupied address in range of 100-115.
Programming of other parameters depends on the individual requirements and is
not obligatory. Configuration of the terminal with RogerVDM requires RUD-1
interface.
CONFIGURATION WITH ROGERVDM PROGRAM
Fig. 1 Connection of the terminal to RUD-1 interface for configuration
Programming procedure with RogerVDM software:
1. Place jumper on MEM contacts (fig. 3).
2. Connect the device to RUD-1 interface according to fig. 1 and connect RUD-
1 to computer’s USB port. The terminal will display CONFIG MODE text and
orange LED SYSTEM will pulsate.
3. Start RogerVDM program, select MCT device, v1.0 firmware version, RS485
communication channel and serial port with RUD-1 interface.
4. Click Connect, the program will establish connection and will automatically
display Configuration tab.
5. Select RS485 communication interface and specify unoccupied RS485
address in range of 100-115 or select Ethernet communication interface and
specify IP address. Configure other low level configuration parameters as
needed.
6. Click Send to Device to update the configuration of device.
7. Optionally make a backup by clicking Send to File… and saving settings to
file on disk.
8. Remove jumper from MEM contacts and disconnect device from RUD-1
interface.
Note: If the USB port does not offer enough current then supply the terminal from
external 12VDC PSU min. 200mA power output.
Note: Do not read any cards nor press keypad when device is configured with
RogerVDM.
MANUAL ADDRESSING
Manual addressing procedure enables configuration of new RS485 address with
all other settings unchanged.
Manual addressing procedure:
1. Remove all connections from A and B lines.
2. Place jumper on MEM contacts (fig. 3).
3. Restart the device (switch power supply off and on). The terminal will display
CONFIG MODE text and orange LED SYSTEM will pulsate.
4. Enter 3 digits of RS485 address in range of 100-115 with keypad.
5. Wait till device starts to emit continuous sound.
6. Remove jumper from MEM contacts and restart the device.
MEMORY RESET PROCEDURE
Memory reset procedure resets all settings to factory default ones including
ID=100 address.
Memory reset procedure:
1. Remove all connections from A and B lines.
2. Place jumper on MEM contacts (fig. 15).
3. Restart the device (switch power supply off and on). The terminal will display
CONFIG MODE text and orange LED SYSTEM will pulsate.
4. Press [*] or read any MIFARE card 11 times.
5. Wait till device confirms reset with continuous sound.
6. Remove jumper from MEM contacts and restart the device.
FIRMWARE UPDATE
New firmware can be uploaded to the terminal by means of included memory
card. The latest firmware file is available at www.roger.pl.
Firmware update procedure:
1. Disconnect power supply.
2. Press and remove memory card from socket (fig. 3).
3. Using memory card reader, copy main firmware (*.frg) to the card and
rename it as FW.BUF. Copy additional firmware (*.cyacd) for keypad and
BLE and rename it as KBDFW.CYA.
4. Insert the card into socket.
5. Connect power supply and wait till device completes starting procedure. The
progress of additional firmware uploading is shown on the display.
6. Disconnect power supply when additional firmware KBD is 100% uploaded.
7. Connect power supply and wait till device completes starting procedure.
8. Start RogerVDM and perform low level configuration.
Note: During the firmware update process, it is necessary to ensure continuous
and stable power supply for the device. If interrupted the device may require
repair by Roger.
APPENDIX
Fig. 2 Enclosure disassembly
Fig. 3 Service contact and memory card

MCT88M-IO Installation Manual 2019-10-02
2/2
Table 1. Screw terminals
Screw terminal
Description
+12V
12VDC power supply
GND
Ground
A
RS485 bus, line A
B
RS485 bus, line B
COM
REL relay common terminal
NC
REL relay output (NC)
NO
REL relay output (NO)
IN1
IN1 input line
IN2
IN2 input line
IN3
IN3 input line
OUT1
OUT1 output line
OUT2
OUT2 output line
1,2,3,4,5,6,7,8
Ethernet port
Table 2. Specification
Supply voltage
Nominal 12VDC, min./max. range 10-15VDC
Current consumption
(average)
~110 mA
Inputs
Three parametric inputs internally connected to
the power supply plus (+12V) through a 5.6kΩ
resistor, approx. 3.5V triggering level when
configured as NO or NC.
Relay output
Relay output with single NO/NC contacts, rated
30V/1.5A
Transistor outputs
Two (IO1,IO2) open collector outputs, 15VDC/1A
rated
Tamper protection
Enclosure opening reported to access controller
Identification methods
ISO/IEC14443A MIFARE Ultralight, Classic,
Desfire EV1 and Plus proximity cards
Mobile device (Android, iOS) compatible with NFC
Mobile device (Android, iOS) compatible with
Bluetooth Low Energy v4.1
Reading range
Up to 7 cm for MIFARE and NFC
Up to 10 m for BLE –depends on ambient
conditions and particular mobile device. Terminal’s
radio power can be increased within low level
configuration.
Distances
Up to 1200 m between controller and terminal
(RS485)
IP Code
IP41
Environmental class
(acc. to EN 50133-1)
Class I, indoor general conditions, temperature:
+5°C to +40°C, relative humidity: 10 to 95% (no
condensation)
Dimensions H x W x D
85 x 155,5 x 21,5 mm
Weight
190g
Certificates
CE
Fig. 5 Connection of terminals and expanders to MC16 access controller
Fig. 6 Connection of door lock, door contact and exit button to MCTxx-IO
terminal
This symbol placed on a product or packaging indicates that the
product should not be disposed of with other wastes as this may
have a negative impact on the environment and health. The user is
obliged to deliver equipment to the designated collection points of
electric and electronic waste. For detailed information on recycling,
contact your local authorities, waste disposal company or point of
purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to
health and the environment. Weight of the equipment is specified in
the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [email protected]
Web: www.roger.pl