Roger MCX2 User manual

MCX2 and MCX8 Installation Manual 2019-10-11
1/2
Roger Access Control System
MCX2 / MCX8 Installation Manual
Firmware version: 2.0.24 and newer
Hardware version: 2.0
Document version: Rev. D
This document contains minimum information that is necessary for initial setup
and installation of the device. The detailed description of configuration
parameters and functionalities is specified in respective Operating Manual
available at www.roger.pl.
INTRODUCTION
The expander is designed to operate in RACS 5 system as peripheral device
connected to RS485 bus of MC16 access controller. Factory new device is
configured with default settings including ID=100 address. Before connecting to
MC16 controller, the device should be assigned with unoccupied address in
range of 100-115. Programming of other parameters depends on the individual
requirements and is not obligatory. Configuration of the expander with
RogerVDM requires RUD-1 interface.
CONFIGURATION WITH ROGERVDM PROGRAM
Fig. 1 Connection of the expander to RUD-1 interface for configuration
Programming procedure with RogerVDM software:
1. Connect the device to RUD-1 interface (fig. 1) and connect the RUD-1 to
computer’s USB port.
2. Restart the device (press RESET button or switch power supply off and on).
3. Within 2-3 seconds place jumper on JP7 contacts (fig. 3 or fig. 4) and LED
PWR will pulsate quickly.
4. Start RogerVDM program, select MCX v2.x device, v2.0 firmware version,
RS485 communication channel and serial port with RUD-1 interface.
5. Click Connect, the program will establish connection and will automatically
display Configuration tab.
6. Enter unoccupied RS485 address in range of 100-115 and other settings
according to requirements of specific installation.
7. Click Send to Device to update the configuration of device.
8. Optionally make a backup by clicking Send to File… and saving settings to
file on disk.
9. Remove jumper from JP7 contacts and disconnect device from RUD-1
interface.
FIRMWARE UPDATE
The update requires connection of expander to computer with RUD-1 interface
(fig. 2) and starting RogerVDM software. The latest firmware file is available at
www.roger.pl.
Firmware update procedure:
1. Connect the device to RUD-1 interface (fig. 1) and connect the RUD-1 to
computer’s USB port.
2. Place jumper on FDM contacts (fig. 3 or fig. 4).
3. Restart the device (press RESET button or switch power supply off and on).
4. Start RogerVDM program and in the top menu select Tools and then Update
firmware.
5. In the opened window select device type, serial port with RUD-1 interface
and path to firmware file (*.hex).
6. Click Update to start firmware upload with progress bar in the bottom.
7. When the update is finished, remove FDM jumper and restart the device.
Fig. 2 Connection of the expander to RUD-1 interface for firmware update
APPENDIX
Fig. 3 MCX2 expander
Fig. 4 MCX8 expander
Table 1. Screw terminals
Screw terminal
Description
+12V
12VDC power supply
GND
Ground
A
RS485 bus, line A
B
RS485 bus, line B
COM
RELx relay common terminal
NC
RELx relay output (NC)
NO
RELx relay output (NO)
IN1..IN8
IN1..IN8 input line

MCX2 and MCX8 Installation Manual 2019-10-11
2/2
Fig. 5 Connection of readers and expanders to MC16 access controller
Table 2. Specification
Supply voltage
Nominal 12VDC, min./max. range 10-15VDC
Current consumption
(average)
30mA (when relays off)
Inputs
MCX2: Two (IN1, IN2)
MCX8: Eight (IN1..IN8)
parametric inputs internally connected to the
power supply plus (+12V) through a 15kΩ resistor,
approx. 3.5V triggering level when configured as
NO or NC.
Relay outputs
MCX2: Two relay outputs
REL1: 30VDC/1,5A
REL2: 30VDC/5A
MCX8: Eight relay outputs:
REL1..REL8: 30VDC/1.5A
Each with single NO/NC contacts.
Distances
Up to 1200 m between controller and terminal
(RS485)
IP Code
IP20
Environmental class
(according to EN 50133-1)
Class I, indoor general conditions, temperature:
+5°C to +40°C, relative humidity: 10 to 95% (no
condensation)
Dimensions W x S x G
MCX2: 80 x 54 x 20 mm
MCX8: 72 x 155 x 20 mm
Weight
MCX2: 50g
MCX8: 115g
Certificates
CE
This symbol placed on a product or packaging indicates that the
product should not be disposed of with other wastes as this may
have a negative impact on the environment and health. The user is
obliged to deliver equipment to the designated collection points of
electric and electronic waste. For detailed information on recycling,
contact your local authorities, waste disposal company or point of
purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to
health and the environment. Weight of the equipment is specified in
the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [email protected]
Web: www.roger.pl