Roger MC16 User manual

MC16 Installation Manual 2020-10-23
1/2
Roger Access Control System
MC16 Installation Manual
Firmware version: 1.6.4 and newer
Document version: Rev. I
This document contains minimum information that is necessary for initial setup
and installation of the device. The detailed description of configuration
parameters and functionalities is specified in respective Operating manual
available at www.roger.pl.
INTRODUCTION
MC16 controller is mainly dedicated to door access control in RACS 5 system.
The controller is master device for such peripheral devices as MCT and PRT
series terminals, Wiegand interface readers and MCX series expanders. Inputs
and outputs of the controller or connected peripheral device can be used to
control such devices as door locks, exit buttons, alarm sirens, etc. Various
versions and types of controllers are based on the same hardware module and
differ with license on their memory cards. Most popular MC16-PAC controllers
are offered in MC16-PAC-x-KIT sets.
CONFIGURATION WITH ROGERVDM PROGRAM
Low level configuration with RogerVDM software enables to define basic
parameters of MC16 controller. Additionally it is necessary to define individual
addresses for MCT and PRT series readers and MCX expanders according to
their installation manuals.
MC16 programming procedure with RogerVDM software:
1. Connect the controller to Ethernet network and define the IP address of your
computer in the same subnetwork as the controller with 192.168.0.213
default IP address.
2. Start RogerVDM program, select MC16 v1.x device, the latest firmware
version and Ethernet communication channel.
3. Select from the list or enter manually the IP address of controller, enter 1234
communication key and start the connection with the controller.
4. In the top menu select Tools and then Set communication key to define your
own password for the controller.
5. In the main window specify your own IP address of the controller.
6. Enable PRT or Wiegand readers if the controller is supposed to operate with
them.
7. Optionally enter comments for controller and its object to facilitate their
identification during further configuration of the system.
8. Optionally backup settings clicking Send to File…
9. Click Send to Device to update the configuration of controller and disconnect
by selection of Device in the top menu and then Disconnect.
CONFIGURATION WITH VISO PROGRAM
High level configuration with VISO software enables to define the logic of
controller. More information on scenarios of operation and high level
configuration is given in MC16 Operating manual as well as AN002 and AN006
application notes.
MEMORY RESET
Memory reset procedure resets all settings to default ones and results in
192.168.0.213 IP address and empty communication key.
MC16 memory reset procedure:
1. Disconnect power supply.
2. Short CLK and IN4 lines.
3. Restore power supply, all LEDs will flash and wait min. 6s.
4. Remove connection between CLK and IN4 lines, LEDs will stop pulsating and
LED2 will be on.
5. Wait approx. 1.5 min till LED5+LED6+LED7+LED8 are pulsating.
6. Restart the controller (switch power supply off and on).
7. Start RogerVDM and make low level configuration.
FIRMWARE UPDATE
New firmware can be uploaded to the controller with RogerVDM software. The
latest firmware file is available at www.roger.pl.
MC16 firmware update procedure:
1. Connect with the controller using RogerVDM software.
2. Backup settings by clicking Send to File…
3. In the top menu select Tools and then Update firmware.
4. Select firmware file and then click Update.
5. After firmware update wait till LED8 is pulsating.
6. Make or restore low level configuration in RogerVDM software.
Note: During the firmware update process, it is necessary to ensure continuous
and stable power supply for the device. If interrupted, the device may require
repair by Roger.
POWER SUPPLY
MC16 controller is designed for power supply from 230VAC/18VAC transformer
with minimal power output 20VA, but it can also be supplied with 12VDC and
24VDC. In case of 12VDC power supply, backup battery cannot be directly
connected to MC16 and in such case backup power supply must be provided by
12VDC power supply unit.
Fig. 1 MC16 power supply
APPENDIX
Table 1. MC16 screw terminals
Name
Description
BAT+, BAT-
Backup battery
AC, AC
18VAC or 24VDC input power supply
AUX-, AUX+
12VDC/1.0 output power supply (for door lock)
TML-, TML+
12VDC/0.2A output power supply (for readers)
IN1-IN8
Input lines
GND
Ground
OUT1-OUT6
15VDC/150mA transistor output lines
A1,B1
RS485 bus
CLK, DTA
RACS CLK/DTA bus
A2,B2
Not used
NO1, COM1, NC1
30V/1.5A DC/AC (REL1) relay
NO2, COM2, NC2
30V/1.5A DC/AC (REL2) relay
Table 2. MC16 LED indicators
Name
Description
LED1
Normal mode
LED2
ON: Service mode (low level configuration)
Pulsing: RAM or Flash SPI memory error
LED3
ON: High level configuration error
Pulsing: Low level configuration error
LED4
No memory card or memory card error
LED5
Event log error
LED6
License error
LED7
Not used
LED8
Pulsating: Proper functioning of the controller
Table 3. Specification
Supply voltage
17-22VAC, nominal 18VAC
11.5V-15VDC, nominal 12VDC
22-26VDC, nominal 24VDC
Current consumption
100 mA for 18VAC (no loads on AUX/TML outputs)

MC16 Installation Manual 2020-10-23
2/2
Inputs
Eight parametric inputs (IN1..IN3) internally connected
to the power supply plus through a 5.6kΩ resistor.
Approx. 3.5V triggering level for NO and NC inputs.
Relay outputs
Two relay outputs with single NO/NC contact 30V/1.5A
rated
Transistor outputs
Six open collector transistor outputs, 15VDC/150mA
rated. Max. total current sink by all outputs up to
3ADC.
Power supply outputs
Two power outputs: 12VDC/0.2A (TML) and 12VDC/1A
(AUX)
Distances
1200m for RS485
150m for and RACS CLK/DTA and Wiegand
IP Code
IP20
Environmental class
(acc. to EN 50131-1)
Class I, indoor general conditions, temperature: +5°C
to +40°C, relative humidity: 10 to 95% (no
condensation)
Dimensions H x W x D
72 x 175 x 30 mm
Weight
approx. 200g
Fig. 2 Connection of readers and expanders to MC16 access controller
Fig. 3 Typical door control with MCT readers
Fig. 4 Typical door control with Wiegand readers
Notes:
In case of read-in door, single reader is connected to the controller. MCT
terminal can be then installed with default ID=100 address.
In case of PRT readers, the diagram is the same as in case of MCT readers
except for connection to CLK and DTA lines instead of RS485 A and B lines.
In case of electrically incompatible Wiegand readers it might be necessary to
install PR-GP-BRD modules.
Diagrams include doors with electric strikes. In case of electromagnetic lock,
the NC terminal of relay is used instead of NO terminal.
Diagrams include exit buttons. In case of read-in/out doors they can be used
for emergency door opening.
This symbol placed on a product or packaging indicates that the
product should not be disposed of with other wastes as this may
have a negative impact on the environment and health. The user is
obliged to deliver equipment to the designated collection points of
electric and electronic waste. For detailed information on recycling,
contact your local authorities, waste disposal company or point of
purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to
health and the environment. Weight of the equipment is specified in
the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [e-mail]
Web: www.roger.pl