Ruijie RG-S7600 Series Installation and operating manual

RG-S7600 Series Switches
Hardware Installation and Reference Guide
Document version: V1.0
Date: 2023-08-11
Copyright © 2023 Ruijie Networks

Copyright
All rights are reserved in this document and this statement.
Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this
document or any portion of this document, in any form or by any means, without the prior written
consent of Ruijie Networks is prohibited.
Trademark and are owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their
respective owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and terms. Some
or all of the products, services or features described in this document may not be within the scope of
your purchase or use. Unless otherwise agreed in the contract, Ruijie Networks does not make any
express or implied statement or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from
time to time. Ruijie Networks reserves the right to modify the content of the document without any
notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not
shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or
errors.

RG-S7600 Series Switch Hardware Installation and Reference Guide
Technical support hotline: [phone]
http://webchat.ruijie.com.cn
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and service engineers
Network administrators
Technical Support
Ruijie Networks website: https://www.ruijienetworks.com/
Technical support website: https://ruijienetworks.com/support
Case portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical support email: [email protected]
Skype: [email protected]
Conventions
1. Signs
The signs used in this document are described as follows:
Warning
An alert that calls attention to important rules and information that if not understood or followed can
result in data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in
function failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will
not lead to serious consequences.

RG-S7600 Series Switch Hardware Installation and Reference Guide
Technical support hotline: [phone]
http://webchat.ruijie.com.cn
Specification
An alert that contains a description of product or version support.
2. Note
The manual offers configuration information (including model, port type and command line interface)
for indicative purpose only. In case of any discrepancy or inconsistency between the manual and the
actual version, the actual version prevails.

RG-S7600 Series Switch Hardware Installation and Reference Guide
- 1 -
1 Introduction to the RG-S7600
RG-S7600 series switches are next-generation and ultra-high-density core switches developed by Ruijie
Networks for all-optical network scenarios. By leveraging CWDM technology, the RG-S7610 series switch
integrates 10 SFG/SFX interfaces in a 1 RU space (equivalent to 80 SFP interfaces or 80 SFP+ logical
interfaces), and the RG-S7620 series switch integrates 20 SFG/SFX interfaces in a 2 RU space (equivalent
to 160 SFP interfaces or 160 SFP+ logical interfaces).
The RG-S7600 series switches are available in four models and support two expansion modules.
Table 1-1 Host Configuration
Model
1000M
SFG
Etherne
t Port
10GE
SFX
Etherne
t Port
100GE
QSFP28
Etherne
t Port
Mana
geme
nt
Port
Cons
ole
Port
USB
Port
Expans
ion
Module
Slot
Fan
Module
Redund
ancy
Power
Module
Redun
dancy
RG-S761
0-10SFG
2CQ
10
N/A
2
1
1
1
1
3+1
1+1
RG-S761
0-10SFX
2CQ
N/A
10
2
1
1
1
1
3+1
1+1
RG-S762
0-20SFG
2CQ
20
N/A
2
1
1
1
1
2+1
1+1
RG-S762
0-20SFX
2CQ
N/A
20
2
1
1
1
1
2+1
1+1
Table 1-2 Expansion Module Configuration
Model
10/100/1000Base-T Port
with Auto-Negotiation
25GE SFP28
Ethernet Port
100GE QSFP28
Ethernet Port
M7600-4GT4VS
4
4
N/A
M7600-2CQ
N/A
N/A
2

RG-S7600 Series Switch Hardware Installation and Reference Guide
- 2 -
Note
The 10GE SFX module is backward compatible with 1000M.
SFP28 ports support 25G/10Gbase-R and 1000base-X, but do not support FEC-RS.
The QSFP28 port can work in 100GE or 40GE mode. The 100GE port can be split into four 25GE ports,
and the 40GE port can be split into four 10GE ports.
The RG-S7600 series switches do not support the V-03281042-620 optical module.
25GE/100GE Ethernet ports of the RG-S7600 do not support Direct Attach Copper (DAC) cables.
Caution
In a domestic environment, this product may cause radio interference in which case the user may be
required to take adequate measures.
This device is not suitable for use in locations where children are likely to be present.
The device has the lithium battery:
1. Replacing the battery with the incorrect type may cause explosion or danger. If the battery is
damaged, replace it with the same type.
2. Exposing the battery to extremely high temperatures and/or extremely low air pressure may cause
the battery to explode or leak flammable liquids or gases.
3. Throwing the battery into a fire or oven, or mechanically crushing or cutting it may cause the
battery to explode.
1.1 RG-S7610-10SFG2CQ
Technical Specifications
Model
RG-S7610-10SFG2CQ
CPU
2.0 GHz quad-core processor
BootROM
16 MB
Flash Memory
8 GB
SDRAM
DDR4 4 GB
Expansion Module
Slot
Supported
Expansion Module
Type
M7600-2CQ or M7600-4GT4VS
Fan Module Slot
4 (3+1 redundancy, and at least three fan modules required)
Fan Module Type
S7610-FAN I-F

RG-S7600 Series Switch Hardware Installation and Reference Guide
- 3 -
Power Module Slot
2 (1+1 redundancy)
Power Module Type
RG-PA550I II-F
Note: The power module is sold and shipped separately. The switch chassis
packaging does not include the power module. The power module must be
ordered to ensure the switch can work properly.
Input Power
AC input:
Rated voltage range: 100 V AC to
240 V AC
Maximum voltage range: 90 V AC
to 264 V AC
Frequency: 50 Hz to 60 Hz
Rated input current range: 7.2 A to
3.5 A
HVDC input:
Input voltage range: 192 V DC to
288 V DC
Rated input current: 3.6 A
Maximum Power
Consumption
270 W
Optical Module Type
See Appendix A.
The supported optical module types may update without prior notice.
Please contact Ruijie Networks for details.
Temperature Alarm
Temperature alarm and over-temperature protection
EMC
GB/T 9254.1
Safety Standard
GB4943.1
Operating
Temperature
0ºC to 45ºC (32ºF to 113ºF)
Storage
Temperature
–40ºC to +70ºC (–40ºF to +158ºF)
Operating Humidity
10% to 90% RH (non-condensing)
Storage Humidity
5% to 95% RH (non-condensing)
Altitude
0 m to 1800 m (0 ft. to 5905.51 ft.)
Weight
6.88 kg (15.17 lbs) (fan modules included during delivery, without power
modules, expansion modules, and packaging)

RG-S7600 Series Switch Hardware Installation and Reference Guide
- 4 -
Dimensions (W x D x
H)
442 mm x 388 mm x 44 mm (17.40 in. x 15.28 in. x 1.73 in.), 1 RU
Warning
In a domestic environment, this product may cause radio interference in which case the user may be
required to take adequate measures.
The nameplate is on the bottom of the chassis.
Nameplate style:
1.1.1 Appearance
The RG-S7610-10SFG2CQ consists of the chassis, power supply system, and cooling system.
The power supply system has four power module slots and supports 1+1 redundancy. You are
advised to configure power redundancy.
The cooling system has eight fan module slots and supports 3+1 fan redundancy. You are advised to
configure fan redundancy.

RG-S7600 Series Switch Hardware Installation and Reference Guide
- 5 -
Figure 1-2 Appearance of the RG-S7610-10SFG2CQ
1.1.2 Front Panel
Figure 1-3 Front Panel of the RG-S7610-10SFG2CQ
Note:
1. Console port
2. System status LED
3. Power module LED
4. Fan module LED
5. MGMT port status
LED
6. MGMT port
7. USB 2.0 port
8. Breathing LED switching
control button
9. Upper and lower row
port breathing LED
10. SFG port
11. SFG port status LED
12. 100GE QSFP28 port
13. Expansion module slot
1.1.3 Rear Panel
Figure 1-4 Rear Panel of the RG-S7610-10SFG2CQ
Note:
①Power module slot 1
②Fan module slot 1
③Fan module slot 2
④Fan module slot 3
⑤Fan module slot 4
⑥Power module slot 2

RG-S7600 Series Switch Hardware Installation and Reference Guide
- 6 -
1.1.4 External Ports
The RG-S7610-10SFG2CQ provides the following ports:
USB port: The USB port is used to connect a USB flash drive to store logs, software versions, alarms,
and other diagnostic information, which can be easily used for online upgrade of device software and
storage of log information.
Console port: The console port is an RS-232 port that uses an RJ45 connector. The console port is
used to connect to the serial port of the background computer for commissioning, configuration,
maintenance, management, and program loading.
MGMT port: The MGMT port is an out-of-band Ethernet port that uses an RJ45 connector. This port
can be connected to an Ethernet port of a PC to download programs. You can manage and maintain
the device remotely by connecting the management port to the Ethernet port of a PC with an
Ethernet cable.
SFG port: There are 10 SFG ports. Each SFG port supports 8 x 1000M logical ports.
QSFP28 port: There are two 100GE QSFP28 ports that support optical modules and AOC cables. It can
work in 100GE or 40GE mode. The 100GE port can be split into four 25GE ports, and the 40GE port
can be split into four 10GE ports.
Caution
To ensure data security and prevent damage to your device, use USB flash drives of well-known
brands and good quality. The USB port is compatible with most USB controllers and may not
recognize some models of USB flash drives.
The RG-S7610-10SFG2CQ supports configuration, maintenance, management, program loading, and
system debugging through the console.
Table 1-3 LEDs
LED
Panel
Identificatio
n
Status
Description
System status
Status
Off
The system is not powered on.