Salus SS881ZB User manual

!Version!2!
!Installation!/!Quick!Start!Guide:!Embedded!Door!Sensor!(SS881ZB)!
Visit%www.salusinc.com%for%the%User%Manual
In#the#Box#
!
Tools#Needed#
NOTE:!
!
!
!
!
!
!
!
!
!
Additional!equipment!may! be!
required! due! to! building!
construction! or! materials,! or!
other! radio! interference! that!
may!reduce!the!radio!range.!
The!open!field!range!is!400m.!
Sensor!w/!Battery!
(1x!CR2,!3V!Lithium)!
Sensor!Sleeve!
Installation!Tool!
(2)!
Drill!Stickers!
(2)!
Installation/User!
Guide!
!
7/8”!Drill!Bit!
Drill!
Rubber!Mallet!
!
PAIRING#INSTRUCTIONS#
• Follow your system’s instructions to prepare to add devices to the system.
• Go to where the sensor is being installed to account for any radio interference.
• Pull the battery tab to start the pairing process.
• When the Sensor is detected and added to the system, proceed to the Sensor
installation.
INSTALLATION#INSTRUCTION#
• Identify the specific location for the sensor and mark the
location with the sticker. The preferred location is in the
doorjamb on the hinge side of the door so that closing the
door will push in the plunger. If there are obstacles beside the
door, such as glass panels, the sensor can be mounted in the
lintel above the door or in the door itself.
• Drill a 7/8” hole at least 2.6” deep through the sticker, and
then remove the rest of the sticker.
• Insert the Sensor Sleeve in the hole until the flange is
seated on the jamb surface. If the sensor needs to be
installed flush with the surface of the jamb, remove the flange
from the Sensor Sleeve before inserting the sleeve.
• Insert the Sensor into the Sensor Sleeve and screw the
Sensor into the Sensor Sleeve until the desired depth is
reached. There will be clicks once the Sensor is past the
minimum number of turns.
• Align the front slots with the grooves in the sleeve for a
positive lock.
• Close the door to verify that the sensor operates properly
and the Sensor does not interfere with the closing of the
door. Screw the Sensor in further if it interferes. If closing
the door does not trigger the Sensor, unscrew the Sensor
a quarter turn each time until it does trigger.
REPLACING#THE#BATTERY#
(Use!only!Duracell!DL-CR2,!Rayovac!RL-CR2,!Energizer!
EL1CR2,!or!GP!Batteries!GPCR2!batteries)!!
• Mark the depth of the Sensor in the Sensor
Sleeve if required.
• Unscrew the Sensor from the Sensor Sleeve
using the installation tool or a coin.
• Remove the battery cover and remove the
battery.
• Insert a new battery into the Sensor, observing
the proper polarity.
• Replace the battery cover.
• Replace the sensor in the Sensor Sleeve at the
original depth.
FACTORY#RESETTING#THE#SENSOR#
• Unscrew the Sensor from the Sensor Sleeve.
• Remove the battery cover and battery.
• Press and hold the tamper switch while re-
inserting the battery.
• When the LED lights, release the tamper
switch.
• The Sensor is now in pairing mode and will
respond to pairing requests.
• Replace the battery cover.
• Replace the sensor in the Sensor Sleeve at the
original depth.
LED#INDICATIONS#
Solid at power up:
Initializing and checking for Factory Reset
3 flashes then pause:
Searching for network to join

!Version!2!
FCC#STATEMENTS#
WARNING: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC#AND#INDUSTRY#CANADA#
RF Radiation Exposure statement:This equipment complies with FCC and
Industry Canada RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum
distance of 20 centimeters between the antenna and all persons.
INDUSTRY#CANADA#
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
SALUS#WARRANTY#
SALUS North America, Inc. (“Salus”) warrants that for a period of two (2) years (“Warranty
Period”) from the date of purchase by the consumer (“Customer”), this device, excluding
batteries (“Product”), shall be free of defects in materials and workmanship under normal
use and service in accordance with all supplied instructions. During the warranty period,
Salus shall, at its option, repair or replace any defective Products, at no charge for the
device. Any replacement and/or repaired devices are warranted for the remainder of the
original Warranty Period or ninety (90) days, whichever is longer.
This warranty does not cover removal or reinstallation costs. This warranty does not apply
to any Product (i) which has been modified, repaired, or altered, except by Salus or an
authorized Salus representative, (ii) which has not been maintained in accordance with
any handling or operating instructions supplied by Salus, or (iii) which has been subjected
to unusual physical or electrical stress, misuses, abuse, negligence or accidents.
This warranty is the only express warranty Salus makes for the Product. Any implied
warranties, including warranties of merchantability or fitness for a particular purpose, are
limited to the Warranty Period or the shortest period allowed by law.
SALUS SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR
INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY
OTHER FAILURE OF THIS PRODUCT. Some states and provinces do not allow the exclusion
or limitation of incidental or consequential damages, or limitation on the duration of
implied warranties of merchantability or fitness, so these exclusions or limitations may
not apply to you.
No oral or written information or advice given by Salus or a Salus-authorized
representative shall modify or extend this warranty. If any term is held to be illegal or
unenforceable, the legality or enforceability of the remaining terms shall not be affected
or impaired.
Customer’s sole and exclusive remedy under this limited warranty is product repair or
replacement as provided herein. If a Product under warranty is defective, the Customer
may:
• contact the party (“Seller”) from which the Customer purchased the Product to obtain
an equivalent replacement product after the Seller has determined that the Product
is defective and the Customer is eligible for a replacement, or
• contact Salus Service at [email protected], to determine whether the device
qualifies for a replacement. If a replacement is warranted and is shipped prior to the
return of the device under warranty, a credit card is required and a hold may be
placed on the Customer’s credit card for the value of the replacement until the
returned device is verified as eligible for replacement, in which case, the Customer’s
credit card will not be charged.
This warranty gives you specific legal rights, and you may also have other rights that vary
from jurisdiction to jurisdiction. If you have any questions regarding this warranty, please
write Salus at:
SALUS North America, Inc.
850 Main Street
Redwood City, CA 94063