Satel INT-SCR-BL User manual

®
MULTIFUNCTIONAL KEYPAD
WITH PROXIMITY CARD READER
INT-SCR-BL
int-scr_en 08/08
The INT-SCR-BL multifunctional keypad with proximity
card reader can operate as:
partition keypad – a device supported by the CA-64 alarm
control panel, as well as INTEGRA control panels with
any firmware version, and identified as INT-S/SK. It is
designed to control arming of one partition. The device
makes it possible to execute the functions of access
control and electromagnetic door lock operation. It
enables changing the user code and calling the control
functions for outdoor devices, and identifies users by
their access code.
partition keypad with proximity card reader – a device
supported by the INTEGRA control panels with firmware
version 1.05 or later and identified as INT-SCR. It
performs identical functions as the partition keypad, but
allows the users to use proximity cards.
entry keypad – a device supported by the INTEGRA
control panels with firmware version 1.05 or later and
identified as INT-ENT. The main task of the entry
keypad is activation of the delay in the partition for the
zones with reaction type 3. INTERIOR DELAYED. The time
period during which these zones will act as delayed
ones is programmable for the keypad. After expiry of the
programmed time, the interior delayed zones again act
as instant ones, unless the partition is disarmed.
Design of the keypad enables it to be installed outdoors.
The device is additionally equipped with a bell button to
control the OC type low-current output. Press the button to
short the output to the common ground.
This manual applies to the module with firmware version
1.01 or later.
1. Description of the Keypad
The partition keypad has 13 keys with permanent or
temporary (automatically activated) mode backlit and LED
indicators:
- ALARM (red color),
- ARMED (green color),
- TROUBLE (yellow color).
Information conveyed by means of the LED indicators depends on the keypad operating mode.
Alternative blinking of all the LEDs (from the left to the right) indicates lack of communication between
the keypad and the control panel. This situation may take place when the STARTER program is
running in the control panel, or when the cable connecting the keypad and the control panel is
damaged.
Fig. 1. INT-SCR-BL multifunctional
keypad.

SATEL INT-SCR-BL
2
Cable color Function
red power supply input (+12 V)
blue ground (COM)
green data (DTA)
black clock (CLK)
yellow relay NO contact (normally isolated from the relay common contact)
pink relay NC contact (normally shorted to the relay common contact)
grey relay C contact (common contact)
brown door status control input (NC type)
violet bell input (OC type)
Table 1. Colors and functions of the keypad cables.
2. Installation and Connection of the Keypad
Use the straight-through unshielded cable for the connection (using the twisted pair type of cable is
not recommended).
Any connections should only be made in deenergized state, i.e. with power supply
disconnected.
1. Remove the locking screw which prevents the casing from being opened and open the casing.
2. Attach the lower part of the casing to the wall.
3. Close the casing and replace the locking screw.
4. Connect the cables: blue (COM), green (DTA) and black (CLK) to the corresponding terminals of
the expander bus on the control panel PCB.
5. Connect the door status control detector to the brown and blue cables. If the door status is not to
be controlled, connect the brown cable to the blue one.
Note: In the entry keypad mode, the door status control detector is not supported.
6. An actuating device (e.g. electromagnetic door lock) can be connected to the relay cables. Use the
yellow and gray cables, if the device is to be activated by closing the circuit. If the device is to be
activated by opening the circuit, use the pink and gray cables.
Note: In the entry keypad mode, the relay is not supported.
7. Connect the module supply to the red (+12 V) and blue (COM) cables. The keypad supply voltage
is not to be necessarily provided from the control panel mainboard. A buffer power supply unit or
another expander with power supply unit can be used for this purpose.
8. The violet lead (bell) can be connected e.g. to the one of the control panel zones.
3. Operating Mode Selection and Address Setting
By default, address 0 and partition keypad operating mode with proximity card reader (INT-SCR) are
set in the keypad.
3.1 Changing the address
1. Turn off the keypad power supply.
2. Disconnect the green and black cables from the terminals of the control panel expander bus.
3. Short together the ends of the green and black cables.
4. Turn on the keypad supply. The keypad will generate 4 short beeps and 1 long beep, and the
LEDs designated [ALARM] andi [ARMED] will start blinking alternately (the ends of green
and black cables can then be separated).

INT-SCR-BL SATEL
3
5. Press in turn the and keys. The keypad will confirm with 2 short beeps that the address setting
function has been launched, and the LED designated [ALARM] will start blinking.
6. Set the address within the range from 0 to 31, using suitable numerical keys and confirming your
selection with the . key. The keypad will confirm with 4 short beeps and 1 long beep that the
address has been set. The LEDs designated [ALARM] and [ARMED] will start blinking
alternately (then, to proceed to setting the operating mode, press in turn the and keys).
7. Turn off power supply.
8. Connect the green and black cables correctly to the expander bus terminals on the control panel
mainboard.
3.2 Changing the operating mode
1. Turn off the keypad power supply.
2. Disconnect the green and black cables from the expander bus terminals.
3. Short together the ends of the green and black cables.
4. Turn on the keypad supply. The keypad will generate 4 short beeps and 1 long beep, and the
LEDs designated [ALARM] and [ARMED] will start blinking alternately (the ends of green
and black cables can then be separated).
5. Press in turn the and keys. The keypad will confirm with 2 short beeps that the operating mode
selection function has been launched, and the LED designated [ARMED] will start blinking.
6. Select the operating mode by pressing in turn::
and – partition keypad with proximity card reader (INT-SCR)
and – entry keypad (INT-ENT)
and – partition keypad (INT-S/SK)
The keypad will confirm with 4 short beeps and 1 long beep that the operating mode has been
selected. The LEDs designated [ALARM] and [ARMED will start blinking alternately (then, to
proceed to setting the address, press in turn the and ).
7. Turn off power supply.
8. Connect the green and black cables correctly to the expander bus terminals on the control panel
mainboard.
4. Starting the Keypad
1. Switch on the alarm system power supply.
2. Conduct identification of a new device in the alarm system. Call the EXPANDER IDENTIFICATION
function (ÁSERVICE MODE ÁSTRUCTURE ÁHARDWARE) from the LCD keypad.
Note: During the identification process, the control panel saves in the module memory a special
(16-bit) number, used for checking the module presence in the system. Replacement of the
module with another one (even having the same address) without a new identification, will
result in triggering the alarm (module tamper – verification error).
3. After identification, the keypad will be supported by the alarm control panel, however most options
and functions will be disabled. For example, the lack of key press confirmation will make an
impression that the keypad does not react to entering the code. Using the LCD keypad or the
DLOADX/DLOAD64 program, assign the users, who will be authorized to use the keypad and
program functions and options of the device.
4. Terminate the service mode or communication with the computer and save the data to FLASH
memory.

SATEL INT-SCR-BL
4
5. Operation in the Partition Keypad Mode
The LEDs show following information:
ALARM red color) – steady light indicates an alarm in the keypad controlled partition, while
blinking indicates that an alarm was triggered in the partition (alarm memory). The LED goes
off when alarm is cleared.
ARMED (green color) – steady light indicates that the partition to which the keypad is assigned
has been armed. Blinking indicates countdown of the exit delay.
TRPUBLE (yellow color) – blinking indicates that a technical problem has occurred. The
signaling applies to troubles from the entire alarm system, not only from the keypad controlled
partition. The type of trouble can be checked on the LCD keypad. Arming the keypad
controlled partition will disable the trouble signaling. Disarming the partition will restore the
trouble signaling.
Note: All LEDs may be OFF in the arming mode, depending on the control panel settings.
Informacje dotyczące użytkowania klawiatury strefowej znajdująsięw instrukcji użytkownika central
alarmowych.
The partition keypad can be programmed by means of the LCD keypad (¼SERVICE MODE
¼STRUCTURE ¼HARDWARE ¼EXPANDERS ¼SETTINGS ¼expander selection) or a computer with
the DLOADX/DLOAD64 program. Described below are settings and options available for programming
Abbreviations from the LCD keypad display are shown at some of the functions.
Name – option to give an individual (16-character) name to the module. This option can be accessed
in the LCD keypad as follows: ¼SERVICE MODE ¼STRUCTURE ¼HARDWARE ¼EXPANDERS
¼NAMES ¼expander selection.
Partition – assignment of the keypad to a partition selected from the list. The keypad controls this
partition.
Lock feature – the option available in the LCD keypad – its activation provides access to the Lock
submenu.
Lock (DLOADX)/ Lock feature (DLOAD64) – its activation provides access to the lock feature options.
The options "Lock feature" (LCD / DLOAD64) and "Lock" (DLOADX) refer to support of the
actuating device (e.g. electromagnetic door lock) by means of the partition keypad. This
function is made available to any user authorized to use the keypad (see: MASTER USERS / USERS
function). Control is effected by means of the relay.
Lock features (DLOADX)/ Lock (DLOAD64)
ON if partition armed – relay is active when the partition is armed (bistable operation).
Note: When operating in this mode the relay will change its state automatically, if the partition
is disarmed from the given keypad. When the partition is disarmed from another keypad,
the state of the relay will change on entering the CODE and pressing the key on the
given partition keypad.
Fixed ON time [ON time] – the relay gets activated for the time period entered in the RELAY ON
TIME function after entering the code (monostable operation).
Fixed ON time – OFF if door open [ON, openÆoff] – the relay is activated after entering the code
and stay active until the door is opened (the door status control input disconnected from the
common ground), but not longer than for the RELAY ON TIME.
Fixed ON time – OFF if door closed [ON, closeÆoff] – the relay is activated after entering the
code and stay active until the door is open (the door status control input cut off from the
common ground) and its normal operating mode is restored on closing the door (reconnection of
the IN input to common ground), but not longer than for the RELAY ON TIME.
Relay ON time – the time period during which the relay is active. Duration of the „relay ON time” can
be from 1to 255 seconds.

INT-SCR-BL SATEL
5
Authorization control [Unauth. event] – opening the door without entering a password from the
keypad (e.g. with the key) will generate an „Unauthorized door opening” event, it can also be
signaled on the output type 93 UNAUTHORIZED ACCESS.
Alarm on unauth. access [Unauth. alarm] – when the partition to which the module is assigned is
armed, unauthorized opening of the door will trigger the alarm and can be additionally signaled on
the output type 94 ALARM – UNAUTHORIZED ACCESS.
Max. door open time – the time after expiry of which the module will report the „Long opened door”
event to the control panel and activate the audible alarm. The duration can be set from 0to 255
seconds.
Dependent on door 1 / Dependent on door 2)– the door which must be closed for the lock to
operate. Monitoring of the door state is effected through the input in the code lock, partition
keypad, or CA-64 SR expander of proximity card readers, or through the control panel zone type
57 TECHNICAL –DOOR OPEN. Two dependent doors can be selected. The function allows to create
a „sluice” type passage.
Code+* do not disarm [Code*n. disarm] – with this option enabled, entering the code, confirmed by
pressing the key will neither disarm the partition nor activate the relay (will prevent the door
from being opened).
Access when armed [Code*in arm] – with this option enabled, entering the code, confirmed by
pressing the key will not disarm the partition, but it will activate the relay (and enable opening
of the door). The option is available when the CODE+* DO NOT DISARM [Code* n. disarm] is
enabled.
Master users / Users – this function defines master users / users authorized to use the given
keypad.
Alarms
FIRE alarm – holding down the key triggers the fire alarm.
AUX. alarm – holding down the key triggers the medical alarm.
PANIC alarm – holding down the key triggers the PANIC alarm.
Silent PANIC alarm – with this option selected, triggering the panic alarm from the keypad will not
set off the loud signaling; instead, a message will be sent to the monitoring station (it can also
be signaled on the output type 12 SILENT ALARM).
Alarm 3 incorrect codes [3 wrong codes] – entering a code unknown to the control panel three
times triggers alarm.
Options
Quick arming – quick arming of the partition:
– fully armed mode – press in turn the and (keys (CA-64 and INTEGRA control panels
with any firmware version) or the and keys (INTEGRA control panel with firmware
version 1.05);
– fully armed mode plus bypassing zones with BYPASSED IF NO EXIT option enabled - press in
turn the and (keys (INTEGRA control panel with firmware version1.06)
– armed without internal – after pressing in turn the and keys (INTEGRA control panel
with firmware version 1.05 or later);
– armed without internal and delayed – after pressing in turn the and keys (INTEGRA
control panel with firmware version 1.05 or later).
Control BI output – the keypad accepts the BI OUTPUTS type of codes.
Control MONO output – the keypad accepts the MONO OUTPUTS type of codes.
Partition blocking – entering the guard code when the partition is armed will temporarily bypass
the partition.

SATEL INT-SCR-BL
6
Guard round control – entering the guard code ended with or key will be recorded as
completion of the round.
Changing access code – this option enables the function of the user code changing.
Signaling
Alarm signal (fixed time) – acoustic alarm signaling in the given partition (through the total
duration of alarm).
Alarm signal (until canceled / latch) – acoustic alarm signaling in the given partition until the
alarm is cleared.
Signaling entry delay – acoustic signaling of the countdown of entry delay time.
Signaling exit delay – acoustic signaling of the countdown of exit delay time.
Auto-Arm delay countdown –acoustic signaling of the countdown of the partition auto-arming
delay.
Access code signaling (hardware) – enabling this option will activate the signaling of code entry
acknowledgement, which is independent of the control panel. The option is useful in expanded
alarm systems, because of a considerable time lag between entering the code and generating
the audible signal by the control panel. Option is available only in the INTEGRA control pane.
Confirming – this option defines the way of communication between the control panel and the
partition keypad user:
No – the function of keypad operation acknowledgement is disabled.
Sound – the keypad generates beeps as described in the user manual for the alarm control panel.
Backlight – – the audible signaling will be replaced by the blinking keypad backlit as described in
the user manual for the alarm control panel.
Backlight – defines the mode of keypad illumination.
No – keypad backlit disabled.
Auto – keypad backlit goes on automatically on pressing any key; the function has additional
options (submenu AUTO-BACKLIGHT in LCD keypad):
−no auto-backlight – illumination only activated by pressing one of the keys,
−zone violation – backlit activated by pressing a key or by violation of the indicated zone,
−entry delay, part. – backlit activated by pressing a key or by starting the countdown of entry
delay time in the indicated partition.
Note: Automatic keypad illumination is ON for approx. 40 seconds from the moment of its
activation or from the last press of any key.
Permanent – keypad backlit is permanently "ON".
No auto-reset after 3 tampers – each expander automatically disables the tamper alarming after
three consecutive (not cleared) tamper alarms. This prevents multiple recording of the same
events in the control panel memory. The option allows this feature to be disabled.
Open door if fire [Doors on fire] – control mode for the door blocking during fire alarm:
−no – fire alarm has no effect on the door blocking,
−Partition fire alarm – fire alarm in the partition will unblock the door controlled by the module,
−Object fire alarm – fire alarm in the object will unblock the door controlled by the module,
−fire alarm – fire alarm in the system will unblock the door controlled by the module.
6. Operation in the Mode of Partition Keypad with Proximity
Card Reader
Information conveyed by the keypad with LED indicators in this mode is identical to that in the
partition keypad mode. Additionally, all LEDs of the partition keypad with reader blinking
simultaneously indicate waiting for the card read-in (during the procedure of adding a card to the
user).

INT-SCR-BL SATEL
7
Information on the use of the partition keypad with proximity card reader can be found in the user
manual of the control panels.
The partition keypad with proximity card reader can be programmed by means of the LCD keypad
(¼SERVICE MODE ¼STRUCTURE¼HARDWARE¼EXPANDERS¼SETTINGS¼expander selection)
or a computer with the DLOADXprogram. The operating mode of partition keypad with proximity card
reader offers all the functions available for the partition keypad mode. Support of the proximity cards
should only be additionally taken into account. Presenting the card to the reader is recognized by the
expander as entering the code, confirmed with the key. Holding up the card for approx. 3 sec. is
recognized as entering the code, confirmed with the key.
7. Operation in the Entry Keypad Mode
In the entry keypad, only the LED designated . is used for signaling. Blinking of the LED informs
that the countdown of delay activation time is running (disarming has no effect on the LED blinking).
Information on the use of the entry keypad can be found in the user manual of the control panels.
The entry keypad can be programmed by means of the LCD keypad (¼SERVICE MODE
¼STRUCTURE ¼HARDWARE ¼EXPANDERS ¼SETTINGS ¼expander selection) or a computer with
the DLOADXprogram. Described below are settings and options available for programming.
Name – option to give an individual (16-character) name to the module. This option can be accessed
in the LCD keypad as follows: ¼SERVICE MODE ¼STRUCTURE ¼HARDWARE ¼EXPANDERS ¼
NAMES ¼expander selection.
Partition assignment of the keypad to a partition selected from the list. The delay activation will apply
to the zones with reaction type 3. INTERIOR DELAYED in this partition.
Master users / Users – this function defines master users / users authorized to use the given
keypad.
Alarm 3 incorrect codes – entering codes / reading cards unknown to the control panel three times
triggers alarm
Control BI output – the keypad accepts the BI OUTPUTS type of codes.
Control MONO output – the keypad accepts the MONO OUTPUTS type of codes.
Guard round control – entering the guard code ended with or key as well as presenting or
holding up the card will be recorded as completion of the round.
Signaling
Delay activation sign. – when the option is enabled, the keypad will signal with beeps the
countdown of delay unblocking time.
Access code signaling (hardware) – enabling this option will activate the signaling of code entry /
card reading acknowledgement, which is independent of the control panel. The option is useful
in expanded alarm systems, because of a considerable time lag between entering the
code / reading the card and generating the audible signal by the control panel.
Confirming – this option defines the way of communication between the control panel and the
keypad user:
No – the function of keypad operation acknowledgement is disabled.
Sound – the keypad generates beeps as described in the user manual for the alarm control panel.
Backlight – the audible signaling will be replaced by the blinking keypad illumination as described
in the user manual for the alarm control panel.
Backlight – defines the mode of keypad illumination
No – keypad backlighting disabled.
Auto – keypad backlighting goes on automatically on pressing any key.
Note: Automatic keypad illumination is ON for approx. 40 seconds from the moment of its
activation or from the last press of any key.
Permanent – keypad backlighting is permanently "ON".

SATEL INT-SCR-BL
8
Delay activation time – the time period during which the zones with reaction type 3.INTERIOR
DELAYED (belonging to the partition to which the keypad is assigned) will act as delayed ones. The
countdown will start running after the code is entered or the card is read in. After expiry of the
programmed time, the interior delayed zones will again act as instant ones, unless the partition is
disarmed.
No auto-reset after 3 tampers – each expander automatically disables the tamper alarming after
three consecutive (not cleared) tamper alarms. This prevents multiple recording of the same
events in the control panel memory. The option allows this feature to be disabled.
8. Technical data
Nominal supply voltage ..................................................................................................12 V DC ±15%
Maximum current consumption..................................................................................................110 mA
BELL output load capacity...........................................................................................................30 mA
Reader operating frequency..................................................................................................... 125 kHz
Maximum voltage switched over by relay .......................................................................................24 V
Maximum current switched over by relay..........................................................................................2A
Operating temperature range .............................................................................................-20...+55 °C
Dimensions ...............................................................................................................47 x 158 x 24 mm
Weight.......................................................................................................................................... 297 g
The latest EC declaration of conformity and certificates are available for
downloading on website www.satel.pl
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
[e-mail]
www.satel.pl