Sauder 101702 User manual

DO NOT RETURN YOUR UNIT
TO THE STORE
Contact us first
www.sauder.com
Most replacement parts ship from our
facility in one or two business days.
For immediate service,
our website is available
24 hours a day, 7 days a week
to order replacement parts,
access assembly tips,
register your product,
and view Sauder products.
Mon-Fri -- 9am-5:30pm ET
United States and Canada (except holidays)
Consumer Services 1--800--523--3987
Lateral File
register your new purchase online
www.sauder.com
Assembly Instructions
09 / 30/ 11
Lot #: 340566
Date Purchased:
Record the date you purchased this unit and save the booklet
for future reference.
If you ever need to contact Sauder about this unit, refer to the
lot # and the model # when calling our toll-free number. For more
information about our furniture, company, or to order replacement
parts, please visit our web site.
Model # 101702
This instruction booklet contains important safety information.
Please read and keep for future reference.
NOTE
register your new purchase online
www.sauder.com
The center pages of this book are French and Spanish
instructions.
Les instructions en français et en espagnol sont situées
dans liencart au milieu de ce manuel. Pour plus de
commodité, celles-ci sont facilement détachables.
Se incluyen las instrucciones en español y francés en el
centro de este folleto. Para facilitar su uso, se puede
desprenderlas fácilmente.
The Camden County Collection

PARTS IDENTIFICATION
101702
(A3) RIGHT
END -- 1 (B3) LEFT END -- 1
(E) BACK -- 1
(F2) LARGE
EXTENSION
BLOCK -- 1
(G2) SMALL
EXTENSION
BLOCK -- 3
(K3) DRAWER
SIDE -- 4 (L2) DRAWER BOTTOM -- 2 (M) TOP MOLDING -- 1
(V) INTERLOCK
TRACK -- 1
(N) BASE -- 1
(Y) TWIST-LOCKR
FASTENER -- 8
(W) CABINET
ACTUATOR -- 2 (X) DRAWER ACTUATOR -- 2 (QQ) FILE CLIP -- 8
(O2) END
MOLDING -- 2
(AA) LOCK -- 1

Each part for this unit may not have a label or inked letter on it. Parts are labeled or inked on the edge to help
distinguish similar parts from each other. Use this PARTS IDENTIFICATION to help identify similar parts.
101702
(C) TOP -- 1 (D) BOTTOM -- 1
(H2) LOCKING
DRAWER
FRONT -- 1
(I2) LOWER
DRAWER
FRONT -- 1
(J3) DRAWER
BOX
FRONT -- 4
(RR) EXTENSION
RAIL -- 4 (SS) EXTENSION SLIDE -- 4
(Extension Set shown separated)
(CC) PULL
MOUNT -- 8 (EE) TOUCH--UP PEN -- 1
(R) STRAIGHT
FILE GLIDE -- 4
(FF) SAFETY
BRACKET -- 1
(DD) ANGLE
BRACKET -- 4
(S) NOTCHED
FILE GLIDE -- 4 (U) ACTUATOR LINK -- 1
(PP) FILE
ROD -- 4
(BB) PULL -- 4

ASSEMBLY TOOLS REQUIRED
HAMMER
NO. 2 PHILLIPS SCREWDRIVER
TIP SHOWN ACTUAL SIZE
AUDER WELCOMES YOU TO THE WORLD OF READY--TO--ASSEMBLE FURNITURE
SSEMBLY IS QUITE SIMPLE IF YOU FOLLOW OUR STEP--BY--STEP INSTRUCTIONS
NPACK PARTS CAREFULLY TO PREVENT SCRATCHING OF THE FINISHED PIECES
O NOT BEGIN ASSEMBLY UNTIL YOU ARE FAMILIAR WITH THE PARTS
XTRA TIME SPENT DURING THE ASSEMBLY WILL BE WELL WORTH IT
EADY....SET....GO
S
A
U
D
E
R
CFCs
The polystyrene foam used in Sauder
packaging contains no CFCs which
are known to reduce stratospheric
ozone layers.
SCREWS SHOWN ACTUAL SIZE
Each time a screw is used, it is shown
actual size for you to compare with the
screw in your hand.
101702
(GG) 1--7/8” PAN HEAD SCREW -- 14 (II) 1--1/4” FLAT HEAD SCREW -- 20
(KK) 9/16” LARGE HEAD SCREW -- 9
(TT) GOLD 5/16” FLAT HEAD SCREW -- 8
(OO) NAIL -- 19
ADJUSTABLE WRENCH TAPE MEASURE
(JJ) 1--1/4” MACHINE SCREW -- 8
(LL) 1/2” FLAT HEAD SCREW -- 4
(NN) 7/16” LARGE HEAD SCREW -- 8

1
Read each step through completely before beginning the step. This box “-” is provided as a check--off box. As you
complete each task, check it off.
-To begin assembly, push a SAUDER TWIST-LOCKRFASTENER (Y) into the large holes in the RIGHT END (A3)
and LEFT END (B3).Repeat this step for the BOTTOM (D).
NOTE: Be sure the TWIST-LOCKRFASTENERS are positioned as shown in the enlarged diagrams.
Make sure the point is positioned as shown in the enlarged diagram. Do not tighten the
TWIST-LOCKRFASTENERS at this time.
NOTE: If you need to remove a TWIST-LOCKRFASTENER from a hole, pull the FASTENER back out
of the hole. Pull at the front and back edges, slowly working the FASTENER out of the hole.
TWIST-LOCKR
FASTENER (Y)
LEFT
END (B3)
Make sure this point
is in this location.
Dowel end
RIGHT
END (A3)
101702
www.sauder.com/services
Look for this icon. It means a video assembly tip is available at:
Repérer cette icône. Elle signifie qu’un conseil de montage vidéo est disponible à :
Busque este icono. Significa que un consejo práctico para ensamble de muebles, grabado en video, está disponible en:
www.sauder.com/services/tips

2
101702
LEFT
END (B3)
-Slide a patented* END MOLDING (O2) onto the notched edge of each END. Carefully slide both MOLDINGS
until the MOLDINGS are even with the top edge of each END.
NOTE: The MOLDINGS should overhang the surface with holes. If the MOLDING overhangs the
wrong surface, remove it and slide it on again. Slide the MOLDING off the notched edge in
the same direction that it was slid on.
*U.S. Pat. No. 5,499,886
Slide the END
MOLDING (O2) onto
the notched edge.
END
MOLDING (O2)
END
MOLDING (O2)
Slide the END
MOLDING (O2) onto
the notched edge.
RIGHT
END (A3)
These edges
should be even.
www.sauder.com/services

3
101702
-Fasten one SMALL EXTENSION BLOCK (G2) to the RIGHT END (A3) as shown. Use three 1--7/8” PAN HEAD
SCREWS (GG) through the large holes in the SMALL EXTENSION BLOCK and into the pre--drilled holes in the RIGHT END.
NOTE: DO NOT OVERTIGHTEN THE SCREWS. Be sure the surface with five holes on the SMALL EXTENSION
BLOCK is facing up. The middle hole is not centered. Use your tape measure. This hole must be
located toward the bottom edge. Follow the diagram closely.
-Fasten two SMALL EXTENSION BLOCKS (G2) to the LEFT END (B3) as shown. Use three 1--7/8” PAN HEAD
SCREWS (GG) through the large holes in the SMALL EXTENSION BLOCKS and into the pre--drilled holes in the LEFT END.
NOTE: DO NOT OVERTIGHTEN THE SCREWS. Be sure the surfaces with five holes on the SMALL EXTENSION
BLOCKS are facing up. The middle holes are not centered. Use your tape measure. These holes must
be located toward the bottom edge. Follow the diagram closely.
-Fasten two ANGLE BRACKETS (DD) to the RIGHT END (A3) and LEFT END (B3) as shown. Use a 9/16” LARGE HEAD
SCREW (KK) through each BRACKET and into the pre--drilled holes in the ENDS.
NOTE: Be sure to position the BRACKETS as shown. Be sure the edges of the BRACKETS are even with the
edges of the ENDS. Follow the enlarged diagrams.
RIGHT
END (A3)
LEFT
END (B3)
SMALL EXTENSION
BLOCK (G2)
9/16” LARGE HEAD SCREW (KK)
(4 used in this step)
ANGLE
BRACKET (DD)
1--7/8” PAN HEAD SCREW (GG)
(9 used in this step)
ANGLE
BRACKET (DD)
Surface with
five holes.
These holes are not
centered. They must
be located toward the
bottom edge.
Bottom
edge
www.sauder.com/services

4
101702
Follow the diagrams closely for this step. Be sure the parts are positioned as shown.
How to use the SAUDER TWIST-LOCKRFASTENER (Refer to the enlarged diagram.)
1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
NOTE: The dowel end of the FASTENER must remain fully inserted in the hole
of the adjoining part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
-Fasten the TOP MOLDING (M) to the TOP (C) as shown. Use four 1--1/4” FLAT HEAD SCREWS (II) through the
TOP MOLDING and into the pre--drilled holes in the TOP.
NOTE: Be sure the finished surface of the TOP MOLDING is facing as shown.
-Fasten the LEFT END (B3) to the TOP (C) as shown. You will need to slide the END MOLDING (O2) on the LEFT
END down as you insert the TWIST-LOCKRFASTENERS into the holes in the TOP. Tighten the TWIST-LOCKR
FASTENERS in the LEFT END.
NOTE: You will need to slide the END MOLDING (O2) down a little to insert the TWIST-LOCKR
FASTENERS into the TOP. The END MOLDING should be against the TOP MOLDING (M) after
the END is fastened.
-Fasten the BOTTOM (D) to the LEFT END (B3) as shown. Tighten the TWIST-LOCKRFASTENERS in
the BOTTOM.
NOTE: Be sure the surface with TWIST-LOCKRFASTENERS on the BOTTOM is facing as shown.
TOP (C)
LEFT
END (B3)
BOTTOM (D)
Groove
END
MOLDING (O2)
TOP
MOLDING (M)
Tighten the FASTENER as tight
as possible after inserting the
dowel end of the FASTENER into
the hole of the adjoining part.
Finished
surface
1--1/4” FLAT HEAD SCREW (II)
(4 used in this step)
Surface with
TWIST-LOCKR
FASTENERS
www.sauder.com/services

5
101702
Flat
edge
RIGHT
END (A3)
-Fasten the RIGHT END (A3) to the TOP (C), then to the BOTTOM (D) as shown. You will need to slide the END
MOLDING (O2) on the RIGHT END down as you insert the TWIST-LOCKRFASTENERS into the holes in the TOP.
Tighten the TWIST-LOCKRFASTENERS in the RIGHT END and BOTTOM.
NOTE: You will need to slide the END MOLDING (O2) down a little to insert the TWIST-LOCKR
FASTENERS into the TOP. The END MOLDING should be against the TOP MOLDING (M) after
the END is fastened.
-Fasten the BASE (N) to the RIGHT END (A3) and LEFT END (B3) as shown. Use a 9/16” LARGE HEAD
SCREW (KK) through each ANGLE BRACKET and into the pre--drilled holes in the BASE.
NOTE: Be sure the flat edge of the BASE is facing as shown. Follow the diagram.
TOP (C)
END
MOLDING (O2)
BOTTOM (D)
BASE (N)
9/16” LARGE HEAD SCREW (KK)
(4 used in this step)
LEFT
END (B3)
TOP
MOLDING (M)
www.sauder.com/services

6
101702
-Tap the INTERLOCK TRACK (V) into the groove in the LARGE EXTENSION BLOCK (F2) using your hammer
as shown.
NOTE: The ends of the INTERLOCK TRACK must be even with both ends of the LARGE
EXTENSION BLOCK.
INTERLOCK
TRACK (V)
The ends of the INTERLOCK
TRACK should be even with
both ends of the LARGE
EXTENSION BLOCK.
LARGE
EXTENSION
BLOCK (F2)
www.sauder.com/services