SDC 45 Series User manual

INSTALLATION INSTRUCTIONS
45 SERIES ELECTRIC STRIKES
P:\INSTALLATION INST\ELECTRIC STRIKES\INST-45\INST-45.vsd REV L 05-18 Page 1
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email [e-mail]
801 Avenida Acaso, Camarillo, Ca. 93041 • [phone] • Fax: [phone]
www.sdcsecurity.com • E-mail: [email protected]
45-4R – 4.875" Radius corners for
aluminum frame.
45-6R – 6.875" Radius corners for
aluminum/wood frame.
45-7R – 7.938" Radius corners for
aluminum/wood frame
MODELS:
45-4S – 4.875" (124mm) Square corners
for hollow metal frames.
FEATURES:
For 5/8” latch or 3/4” latch with 1/8” door gap.
Latch bolt monitor standard.
Keeper closed & deadlocked standard.
Field selectable failsafe / failsecure.
Field selectable voltage, 12/24V AC/DC
AC with Rectifier (BR64XL)
1/4” horizontal alignment adjustment.
Plug-in wire connectors.
Low profile, 1-3/16” deep
All stainless steel parts with durable die
cast body for corrosion resistance.
Fewer moving parts for maximum life.
630 stainless steel standard.
ANSI A156.31
UL Listed (BP10254)
U.S. Patent #7,540,542 B2

P:\INSTALLATION INST\ELECTRIC STRIKES\INST-45\INST-45.vsd REV L 05-18 Page 2
Typical Aluminum Frame
Failsecure standard. Field adjustable from Failsecure to Failsafe as shown.
[30.48]
1.2
[31.75]
1.25
[123.83]
4.875
[85.73]
3.375
#12-24
Screws
MOUNTING
TABS
Typical Hollow Metal Frame
[30.48]
1.2
[31.75]
1.25
[104.78]
4.125
[85.73]
3.375
[123.83]
4.875
#12-24 Screws
Faceplate
1-1/4 x 4-7/8
[31.75 x 123.83]
FAILSECURE
FAILSAFE

P:\INSTALLATION INST\ELECTRIC STRIKES\INST-45\INST-45.vsd REV L 05-18 Page 3
Horizontal Adjustment
Remove Faceplate. Loosen Horizontal Adjustment Screws and slide Die Cast
Body out as needed. Retighten Adjustment Screws and replace Faceplate.
Horizontal Adjustment
Screws
Die Cast Body
Keeper/Deadlocked: Purple – COM
Brown - N/O
Yellow - N/C
Latch Status: Orange - COM
White - N/O
Grey - N/C
Solenoid: Black, Red, Blue & Green
Electrical Data:
Dual Voltage: 200/100mA @ 12/24VDC
140/70mA @ 12/24VAC
Monitoring:
Latch Status: SDPT, dry 3Amp @ 30V (standard)
Keeper Closed and Deadlocked (standard)
Keeper Open/Closed Status: SPDT, Dry 3Amp @ 30V
(optional)
Keeper-Open/Closed:
Wht/Blk – COM
Yel/Blk - N/O
Org/Blk - N/C
The electric door strike shall be
installed in such a way as not to impair
the operation of an emergency exit or
panic hardware mounted on the door.
Wire leads must not be connected to
conductors larger than18AWG
Notes: Red
Black
Blue
Green
Red
Black
Blue
Green
12V 24V
MOV
MOV

P:\INSTALLATION INST\ELECTRIC STRIKES\INST-45\INST-45.vsd REV L 05-18 Page 4
45 SERIES ELECTRIC STRIKE FRAME PREPARATION
FOR HOLLOW METAL FRAMES
HOLLOW METAL,
SQUARE CORNER
FACEPLATE
ALUMINUM / WOOD
RADIUS CORNER FACEPLATES
2X
.375
1.250
2X
.625
4.875
45-4S
1.500
2X 1.688
1.250
2X
.625
2X
.375
45-6R
6.875
1.500
2X
2.688
4X R
.125
MATERIAL THICKNESS = .110
CENTER LINE OF STRIKE
AND LOCK BOLT OF LOCK
SHOULD ALIGN HORIZONTALLY
C
L
C
L
.375
1.2
3.375
.250
4.875
2X TAP FOR
#12-24 UNC THDS
THRU
2X .110 MTG
TAB DEPTH
(TYP)
= SIZE DEPENDANT ON
MODEL ORDERED
45-7R
1.500
2X
3.219
1.438
2X
.719
4X R
.125
2X
.375
7.938
MATERIAL THICKNESS = .110
ALUMINUM
RADIUS CORNER
FACEPLATE
MATERIAL THICKNESS = .110
2X 1.688
2X
.375
1.250
2X
.625
45-4R
1.500
4X R
.125
4.875