SDC FS23M Series User manual

OVERHEAD INSTALLATION HORIZONTAL
1. Examine the top rail of the door for the most suitable location for the strike plate. Mark the door for the end of the strike closet to
the lock stile, and make a corresponding mark on the header to line up with the first mark.
2. Locate center line of door thickness on the header and attach adhesive cut out template to header. Lining it up with marks, center
punch the tab-mounting screw locations and counter-sink for #10 screw. Saw or rout out the cutout area. Continue to step 5.
SIDEJAMB INSTALLATION VERTICAL
3. Examine the lock stile jamb for the point nearest the center of the door height, with space available for the lock and strike. Mark
the door stile horizontal for the top end of the strike plate and make a corresponding mark on the jamb.
4. Locate center line of door thickness on the jamb and attach adhesive cutout template to jamb, lining up the top of the cutout with
the horizontal mark on the jamb. Center punch the tab mounting screw locations and counter sink for #10 screw. Saw or rout the
cutout.
5. Attach the mounting tabs inside.
6. (FS23M only) bore 5/16” hole for pilot lamp on inside face of frame as shown on the template.
7. Attach power supply leads to lock leads as shown on page 2. Handle the lock carefully; do not hang it by the wire leads. Insert
wiring into the header cavity carefully so they do not interfere with proper locating of the lock in the cutout.
8. Insert lock. When installed horizontally, the bolt end is nearest the lock stile. When installed vertically on the sidejamb, the bolt
must be at the top end of the cutout. Secure with #10-32 machine screw.
9. Using strike plate as a template, mark screw hole location and drill holes for screws supplied. Mortise as required. Attach strike.
10. The Automatic Relock Switch (ARS) is set for 1/8” clearance between the top of the door and transom bar or head jamb. Any
additional gap may be compensated for by loosening the lock nut and turning the switch assembly clockwise until proper
adjustment is reached. Be sure to tighten lock nut when adjustment is satisfactory.
P:\INSTALLATION INST\BOLT LOCKS\INST-90 DEG REV J 12-21 Page 1
Easy Installation or Servicing
All Space Saver locks are
easily installed in any existing
entrance merely by mortising
out a cutout, attaching the
wiring, inserting the lock, and
bolting it into position with two
attaching tabs. Cutting studs is
no longer a problem or
expense.
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email [e-mail]
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
FS23M, 1090, 1190 SERIES
1. Mortise cutout in
tube for face plate
(fits flush with
surface of tube).
2. Position screws
for attaching
tabs, drill holes,
attach tabs.
4. Slide lock into
position, attach
to tabs.
3. Connect wiring
to lock.
1. Mortise cutout in
tube for face plate
(fits flush with
surface of tube).
2. Position screws
for attaching
tabs, drill holes,
attach tabs.
4. Slide lock into
position, attach
to tabs.
3. Connect wiring
to lock.
Fig. 2
Auto Relock Switch (ARS)
Adjustable for Wide Door Gap
Loosen nut.
Turn assembly
clockwise for wide
door gap.
Tighten nut.
Fig. 1 Fig. 2
Auto Relock Switch (ARS)
Adjustable for Wide Door Gap
Loosen nut.
Turn assembly
clockwise for wide
door gap.
Tighten nut.
Fig. 1

P:\INST INSTRUCTIONS\BOLT LOCKS\INST-90 DEG REV J 12-21 Page 2
NOTE: The SDC PR-1000 Power Regulator in included with the bolt lock. Although the solenoid is rated for continuous
duty, continuously powering the solenoid will generate heat. Installing the PR-1000 reduces the power consumption of
the bolt locks after activation of the lock, allowing for a heat reduction to the bolt lock, and increasing the life of the
solenoid. DC voltage is recommended for improved heat reduction.
FS23M, 1091A/1019ADL, 1190A (without PR-1000):
FS23M, 1091A/1019ADL, 1190A (Wiring with PR-1000; recommended):
Solenoid Voltage Configuration:
PR1000 Input Voltage:
12/24 VDC/VAC (+/-10%) NOTE: 1190A will operate at 24VDC only. DC voltage is recommended for optimal performance.
TROUBLE SHOOTING
YEL/BLK
YEL(~) or (+DC)
BLK (-DC)
RED (+)
WHT(-)
ORG
BLU
WHT/BLK NOT
USED
SOLENOID * See below for
solenoid wiring
N/C
N/O
COM
(~)
(~) AC
POWER
PR-1000
VOLTAGE
REGULATOR
+
(-)
DC
POWER
INPUT
(DOOR CLOSED)YELYEL Lock ARS
YEL/BLK
YEL(~) or (+DC)
BLK (-DC)
RED (+)
WHT(-)
ORG
BLU
WHT/BLK NOT
USED
SOLENOID * See below for
solenoid wiring
N/C
N/O
COM
(~)
(~) AC
POWER
PR-1000
VOLTAGE
REGULATOR
+
(-)
DC
POWER
INPUT
(DOOR CLOSED)YELYEL Lock ARS
24VDC SOLENOID
CONFIGURATION
(All models, except 1190A)
Red (+)
BLK
BLU
WHT(-)
24VDC @
450mA (max)
24VDC ONLY
SOLENOID
(Model 1190A only)
Red (+)
WHT(-)
24VDC @
700mA (max)
24VDC ONLY
SOLENOID
(Model 1190A only)
Red (+)
WHT(-)
24VDC @
700mA (max)
12VDC SOLENOID
CONFIGURATION
(All models, except 1190A)
Red (+)
BLK
BLU
WHT(-)
12VDC @
900mA (max)
12VDC SOLENOID
CONFIGURATION
(All models, except 1190A)
Red (+)
BLK
BLU
WHT(-)
12VDC @
900mA (max)
24VDC SOLENOID
CONFIGURATION
(All models, except 1190A)
Red (+)
BLK
BLU
WHT(-)
24VDC @
450mA (max)
24VDC ONLY
SOLENOID
(Model 1190A only)
Red (+)
WHT(-)
24VDC @
700mA (max)
12VDC SOLENOID
CONFIGURATION
(All models, except 1190A)
Red (+)
BLK
BLU
WHT(-)
12VDC @
900mA (max)
RED = N/O
WHT = COM
BLU = N/C
DPS polarity shown with door closed
BPS polarity shown with bolt retracted.
RED = N/C
WHT = COM
BLU = N/O
ARS
DPS / BPS CONFIGURATION
BPS
DPS
RED = N/O
WHT = COM
BLU = N/C
DPS polarity shown with door closed
BPS polarity shown with bolt retracted.
RED = N/C
WHT = COM
BLU = N/O
ARS
DPS / BPS CONFIGURATION
BPS
DPS
Problem:
Bolt does not project.
Bolt projects but chatters.
Bolt will not retract.
Solution
Check voltage and alignment of strike.
Voltage too low.
Strike is mis-aligned.
Electrical Data
Dual Voltage Solenoid: FS23M / 1091A / 1091ADL
12VDC @ .9 Amp (Max) Continuous Duty
24VDC @ .45 Amp (Max) Continuous Duty
24VDC Solenoid (1190A)
24VDC @ .7 Amp (Max) Continuous Duty
OPTIOINAL BOLT POSITION SENSOR (BPS-MAGNETIC)
B Indicates bolt locked or unlocked 5 Watt
OPTIOINAL DOOR POSITION SWITCH (DPS-MECHANICAL)
D Indicates door opened or closed 4A @ 30VDC (Resistive)
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
N/C
N/O
Access
Control or
Push Button
(N/C)
COM
(DOOR CLOSED)
YELYEL
SOLENOID
+
(-)
+
(-)
DC
POWER
INPUT
N/C
N/O
Access
Control or
Push Button
(N/C)
COM
(DOOR CLOSED)
YELYEL
SOLENOID
+
(-)
+
(-)
DC
POWER
INPUT