Smanos L020 User manual

Printed in China
PA: L020-UM-EN/DE/FR/NL-V1.0
© 2015 SMANOS HOLDING LTD. All Rights Reserved.
L020
Security Alarm System
MULTILINGUAL
USER MANUAL
EN IT ES PT
MULTILINGUAL
USER MANUAL
EN DE FR NL

Table of Contents
Please read this user manual carefully.
Be sure to keep this user manual handy for future reference.
VIDEO
Introduction ������������������������������������������������������������������������������������������������01
Features ��������������������������������������������������������������������������������������������������������01
In the Box���������������������������������������������������������������������������������������������02~03
How It Works����������������������������������������������������������������������������������������������04
Overview�������������������������������������������������������������������������������������������������������05
Power on and Network Setup��������������������������������������������������������������06
Accessories������������������������������������������������������������������������������������������07~09
Remote Control..................................................................................... 07
Zone modes........................................................................................... 08
Door/Window Contact ....................................................................... 09
APP Operation������������������������������������������������������������������������������������11~14
Apple and Android App...................................................................... 11
Managing Your Alarm System........................................................... 11
Pairing/Deleting Accessory�����������������������������������������������������������15~16
Pairing New Remote Control and Sensor....................................... 15
Pairing New Wireless Siren................................................................. 16
Deleting Sensors and Remote Controls.......................................... 16
Deleting Wireless Siren........................................................................ 16
Restoring to Factory Setting�����������������������������������������������������������������17
Reload the Batteries of Accessories���������������������������������������������������18
Trouble Shooting���������������������������������������������������������������������������������������19
Maintenance ���������������������������������������������������������������������������������������20~21
Specications��������������������������������������������������������������������������������������22~23
L020 Control Panel .............................................................................. 22
RE2300 Remote Control...................................................................... 23
DS2300 Door/Window Contact ........................................................ 23
Disclaimer�����������������������������������������������������������������������������������������������������24
Industry Canada Notice
This device complies with Industry Canada licence-exempt RSS standard(s).
1. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
ENEN

01 02
Introduction
Congratulations in buying the L020 alarm system. This product
is a totally D.I.Y. home security solution. It features automatic
connection to various accessories, putting your home under all-
round protection.
To experience this wonderful product, please follow the
instructions in the user manual. If there is any problem when using
the product, please contact us for help.
Features
1. Easy to operate
Connect network within 10 seconds
Interact by APP
Support entry and exit delay
Two groups of timing arm and disarm
2. High reliability
Built-in 1,000,000 RF codes combination
Built-in 105dB siren, deterring intruders
3. User-oriented
Standby over 10 hours
Support 10 remote controls, 30 wireless detectors
In the Box
Please check whether the package includes the following items. If
not, please contact the distributor/ retailer.
L020 Control Panel x 1 Battery of Control
Panel x 4
DS2300 Door/Window
Contact x 2
Network Cable x 1
ENEN

03 04
RE2300 Remote Control x 1 SA-A12 Adapter x 1
Warranty Card x 1 Reset Pin x 1
How It Works
Paired Door/Window Contact
Door or window is opened
Managed by remote
control / phone
Panel sounds / Sends a
push notication to users
Users
ENEN

05 06
Overview
Front
+
_
+
_
_
+
_
+
Status Indicator
Rear
+
_
+
_
_
+
_
+
Reset Button
Battery
Side
+
_
+
_
_
+
_
+
App Pairing Button
Network Cable Jack
Adapter Jack
Power on and Network Setup
②
①
Follow the illustrations above to connect the control panel with
power and router. Wait until the status indicator stops blinking
but keeps on, means it has connected with Internet.
Note: The control panel would not be able to control or push alarm
notication in case of power failure (even powered by batteries) or network
cable is cut, when alarm occurs, the control panel hoots on site.
Installation: The control panel is suggested to be installed in the
central of the system or open area for optimal performance and
avoid load-bearing wall or home electronics which may cause
signal attenuation.
ENEN

07 08
Accessories
Remote Control
Overview
LED Indicator
Guide Point For The Blind
Arm
Disarm
Stay
SOS
Metal Ring
Note: If you press any button, the LED indicator is dusky and lights off after
ashing twice quickly, means the remote control battery is exhausted.
Button System Status
Press once to arm the system. The siren beeps once and the
red indicator will light on to conrm the system is armed.
Press once to disarm the system. The siren beeps twice and the
green indicator will light on to conrm the system is disarmed.
Note: System will alarm immediately if 24-hour zone detector
or tamper switch of sensor is triggered.
Press once to home arm the system, the siren beeps once after
3 seconds and the blue indicator will light on to conrm the
system is in home mode.
Note: System stops handling signal from home mode zone
detector, which enable users to move freely at home.
The control panel will hoot on-site with indicator ashing, users
will receive an emergency message from App.
Press the [stay ] button, the indicator on the remote control
blinks once, and then press [Arm ] button within 3 seconds
to mutely arm the system.
Press the [stay ] button, the indicator on the remote
control blinks once, and then press [Disarm ] button within
3 seconds to mutely disarm the system.
Zone modes
There are three zone modes available for the sensors.
Normal zone: In arm or home arm state, the detectors set to
normal zone work normally. Once intrusion is detected, the
detectors trigger an alarm.
Home mode zone: When system is in home arm state, the
detectors set to home mode zone are disarmed. The detectors set
to other zones are armed. That is, partial arm.
24-H zone: The detector set to 24-H zone trigger an alarm
immediately when detecting intrusion, no matter the system is
armed or disarmed.
Sensors in This Kit Zone Mode (Default Setting)
DS2300 Door/Window Contact Normal Zone (can be changed through
App)
Note: The zone mode of 24-hour zone sensor can not be changed.
ENEN

09 10
Door/Window Contact
The contact contains a transmitter and a magnet, which can be
mounted on a door, window or any objects that can be opened
or closed. When the transmitter and magnet are separated over
2 cm, the contact will send a signal to the control panel to trigger
an alarm.
Overview
LED Indicator
Transmitter
Front Side Back Side
Magnet
Tamper Switch
LED Indication
Blinks once: Door/window open detected.
Blinks once per 3 seconds after triggered: Low battery. Push
notication will be sent to App. Please change battery as soon as
possible.
Note: When tamper switch is pressed, system will alarm immediately.
Installation
Make sure the contacts work properly before installation.
Step 1: Choose a suitable installation location
It can be installed on doors,
windows or any other objects that
can be opened or closed. If it is
applied to metal doors, please
place spacer under the transmitter
and magnet.
Step 2: Secure the contacts with double-sided tapes
Make sure the triangle marks on
the side of transmitter and magnet
are closed to each other and within
the range of 1cm. As long as the
space between them is over 2cm,
the LED on the transmitter will blink
once.
>2cm
ENEN

11 12
APP Operation
Apple and Android App
Download App from App Store or Google Play by searching
keywords “L020 Alarm”.
L020 Alarm
Special Tips (For Iphone Only)
Tap “OK” to allow receiving notications
from “L020 Alarm”.Forbidden to receive
notications may result in an application
running failure, please re-install and
allow it to send notication to you in
case of alarm.
Managing Your Alarm System
The App can be bound with the alarm system through smart
phones. And this alarm system can be controlled by multiple
users.
Please make sure the control panel has been powered by
adapter. It will be disconnected with network when powered only
by batteries.
Registration and App pairing setup
After registration, please follow the step descriptions on App to
complete the App pairing setup.
Please make sure your smartphone is connected with the Wi-Fi
which is same as the control panel’s.
Remote control your alarm system
Arm
Pull-down
to Refresh
Network Reconnection
Disarm
Home Arm
ENEN

13 14
System settings
① Edit Accessory
10 remote controls and 30 sensors could be extended and the
names of sensors are editable.
This function aims at guiding user to identify the invasion location
quickly by changing the sensor name. Their sequence in naming
follows pairing order, for example, the rst paired sensor is by
default assigned to zone 1, the second paired sensor is by default
assigned to zone 2, etc. In case of emergency, this control panel
will push notication with zone number (or new name) to user.
Meanwhile, you can change the working mode of accessory
(Except the 24-hour zone sensor) by tapping the [ ] or [ ],
please refer to the detail of “zone mode” on page 8.
② Wireless Siren
If wireless siren is purchased, you can setup on the app to turn on/
off the alarm function and arm/disarm tone, etc.
③ Exit Delay Time & Entry Delay Time
If you don’t want to carry along remote controls, you can set the
exit or entry delay.
Suppose entry delay is set at 30 seconds, the system will allow you
30 seconds to disarm the system before alarming. Suppose exit
delay is set at 35 seconds, the system will allow you 35 seconds to
leave before the system is armed. The “beep” is heard in every 2
seconds to remind you to leave. The pace of reminding sound will
speed up in the last 15 seconds. Thus leaves you enough time to
leave home without triggering the system.
④ User Deletion
Input the ID No. (on the back side of the control panel) to delete
all the users.
ENEN

15 16
Pairing/Deleting Accessory
The included accessories have been paired with the control panel
by default, if you want to pair new accessories, please follow these
instructions:
Pairing New Remote Control and Sensor
Ta p [+] on the accessory interface to send out pairing signal, and
then trigger the accessory by following the illustration.
Important: Please don't trigger the tamper switch of sensor when
pairing, otherwise the system will recognize the sensor as a 24-hour
zone sensor.
Press any button on the
remote control
Press the test button
more than twice(Purchase
separately)
Separate the transmitter
and the magnet
When a beep is heard from the control panel means the sensor
is paired successfully. If two beeps are heard, it means the sensor
has already been paired.
Note: To pair other sensors, please refer to the related user manuals.
Pairing New Wireless Siren
Wireless siren is sold separately.
1. Siren enters pairing state (please refer to its user manual).
2. Arm or disarm the control panel on App to send out pairing
signal to the siren.
When a beep is heard from the siren means the siren is paired
successfully. If two beeps are heard means the siren has already
been paired.
Deleting Sensors and Remote Controls
Use the supplied reset pin to press the reset button for about
3 seconds, the control panel will beep once to indicate all the
sensors and remote controls have been deleted.
Deleting Wireless Siren
Press and hold the pair button of the wireless siren, the deletion
is succeeded when one beep is heard from the wireless siren.
ENEN