SOMFY Clever User manual

Tilt Blind Motorization Kit
Installation Guide
Trousse de motorisation de store inclinable
Guide de montage

CONTENTS
Pre-check 1
Product compatibility 2
Inside this package 2
Other items you may need 3
Blind components 4
Step 1 - Remove the blinds 5
Step 2 - Prepare for motor installation 8
Step 3 - End-mount installation 13
Step 4 - Center-mount installation 14
Step 5 - Finishing up 16
Step 6 - Remote control setup 17
TABLE DES MATIÈRES
Vérification préliminaire 25
Compatibilité du produit 26
Compris dans cet emballage 26
Autres articles possiblement requis 27
Composants du store 28
Étape 1 - Dépose du store 29
Étape 2 - Préparation pour l’installation du moteur 32
Étape 3 - Montage en extrémité du store 37
Étape 4 - Montage en partie intermédiaire du store 38
Étape 5 - Finalisation de l’installation 40
Étape 6 - Configuration de la télécommande 41
Scan this code with your smart device
for a helpful video showing how easy your
Clever™ installation can be. Or, visit
somfysystems.com/clever
Pour obtenir un clip vidéo montrant à quel point
l’installation de votre moteur Clever™ peut être
facile, balayez ce code avec votre appareil intelligent.
Ou, visitez somfysystems.com/clever

EN
1
PRE-INSTALLATION CHECK-LIST
We want your Clever™installation to go as smoothly and easily as possible, so please take a moment to answer the
questions below and read the important safety information before you begin.
Are your blinds 2” to 2-1/2” in depth, measured front to back? Yes
No
Are your blinds made of wood, composite or imitation wood?
Yes No, they’re vinyl or aluminum
Are the blinds located indoors?
Yes No, they’re outside
Do you raise and lower them using a cord?
Yes No, they’re cordless
2⁄”
(57mm)
2” (51mm)
3
2⁄”
(57mm)
1½” (38mm)
2
2⁄”
(57mm)
1½” (38mm)
1
CAUTION Check headrail
for any visible damage.
Does the headrail of your blinds match one of styles shown here?
Yes No
See page 4 for reference to find headrail and other blind components.
Are your headrails metal? Yes No
Are you ready to start enjoying the convenience and luxury of motorized blinds? Yes No
If you answered “No” to any of these questions, this may not be the right motorization solution for your blinds. Please visit
somfysystems.com to connect with a Somfy Expert.
Installation Guide
EN

EN
2
PRODUCT COMPATIBILITY
Clever is intended for the tilt function control of made-to-measure horizontal blinds. Clever is typically not compatible with off-the-shelf
blinds or blinds that are cut down to size at big box retailers.
Clever is compatible with popular brands widely available through online stores,as well as major retailers. It is still important to verify that
the headrail style is compatible before installing,as there is some variation in the market.
Not sure of your brand? No worries. Simply try each of the included adaptors until you find the perfect fit.
INSIDE THIS PACKAGE
NOTE: Ensure you also have a Somfy battery option & remote control device.
If you are missing any of these items from your kit, please contact Somfy.
B1 B2 B3
A -Somfy Clever motor B -Headrail Adaptors – 3 sets of 2 each
(to fit the profiles shown on the previous page)
C -Tilt Rod Adaptors - set of 7
.24” (6mm)
Square
C2
.16” (4mm)
Square
C3
.24” (6mm)
Hexagonal
C4
.22” (5.6mm)
Hexagonal
C5
.2” (5mm)
Hexagonal
C6
D-rod
Adaptor
C7
.25” (6.4mm)
Square
C1

EN
3
OTHER ITEMS YOU MAY NEED
• A flat-head screwdriver
• A hammer
• A ruler or measuring tape
• A pair of pliers
• A pair of scissors
• A step ladder
• A second set of hands when taking down and
re-attaching the blinds can be helpful
• A can-do, positive attitude – because you’ve got this!
IMPORTANT INSTALLATION & SAFETY TIPS
• Use reasonable care and caution when handling the Clever motor and control device.
• Make sure you use a genuine Somfy controller for all your Clever motorized blinds. Somfy offers multi-channel remote control devices
to accommodate any motorized blind application, whether single blind or multiple blind installations. Please visit somfysystems.com for
more information.
• Use care when inserting the motor into the headrail. The edge of the blind headrail can be sharp.
• Be careful not to drop, impact,or puncture the Clever motor or immerse it in any liquid. If your motor has been damaged in any way, please
contact Somfy for assistance.
• Follow each of the steps outlined in the installation instructions that follow. Failure to follow these instructions may result in accidental damage
to your window blind. Also, please don’t use Somfy Clever for anything other than its intended use, as this will void the product warranty.
• And most importantly,don’t worry too much. Just roll up your sleeves, follow the steps, and you’ll be done in no time!

EN
4
BLIND COMPONENTS
Before you dive right in, please take a moment to get familiar with the names of the various parts inside your blinds.
End Cap Cord Lock
(Lift Mechanism) Tumbler Tilt Rod
Valance
Blind Bracket
Headrail
Tilter Hook/Sleeve
Lift Cord
Slats
Tassels
Bottom Rail
Tilt Mechanism
(Wand or Cord)
HEADRAIL - TOP VIEW
FULL BLIND ASSEMBLY WITH TILT WAND OR FULL BLIND ASSEMBLY WITH TILT CORDS
Tilt Wand
Tilt Cords
NOTE: LIFT OR TILT CORDS AND/OR WAND POSITION MAY DIFFER.

EN
5
STEP 1REMOVE THE BLINDS
1a. Carefully remove any valances or decorative covers from the top-front of each blind to be motorized.
1b. Manually tilt the blinds to the fully open position. Then raise the blinds all the way up. If your blind has a tilt wand, remove it now.
Tilt Wand
Removal

EN
6
1c. Open the blind brackets on each end of the blind. NOTE: Some brackets open upward from the bottom; others may swing outward to
the side. You may need to use a screwdriver to help open them.
Upward Swing Outward Swing
1d. Carefully remove the blind away from the open brackets, as shown. Then remove the blind from the window area and place on
a flat work surface.

EN
7
1e. Use a hammer and screwdriver to gently tap off both end caps.
CAUTION Headrail edges may be sharp, so take care when working with it.

EN
8
STEP 2PREPARE FOR MOTOR INSTALLATION
IMPORTANT Before you install the Clever motor, it is important to make certain that it and the headrail adaptors
will fit securely in the headrail. Remove the headrail adaptors included in the packaging and make certain that
at least one pair fits properly in the headrail – not too loose or too tight. If the fit isn’t right, please contact Somfy at
1-800-822-7468 and do not proceed with the installation.
2a. Select the correct pair of headrail adaptors (B) that best match the size & shape of your blind’s headrail. Set them aside.
B
B1 B2 B3
2b. Select the tilt rod adaptor (C) that best matches your blind’s tilt rod. NOTE: Only one tilt rod adaptor is required. Set it aside.
C
C1 C2 C3 C4 C5 C6 C7

EN
9
2c. If present, remove the C-Clip or retaining device from the tilt rod.
2d. Disengage the tilt rod by sliding it out and away from the tilt mechanism. NOTE: Pliers may be needed for this step.
2e. If you have a wand tilt mechanism, gently twist and remove it from the headrail. NOTE: Pliers may be needed for this step.
NOTE: If you have tilt cords go to step 2f.

EN
10
NOTE Skip steps 2f and 2g if your tilt mechanism uses a wand.
2f. To remove the tilt cords: Use scissors to snip the knot at the end of the cord, beneath the tassel. Cut as close to the knot as possible.
Then pull the cord up and through to remove the tassel. NOTE: Be certain you are cutting the TILT CORDS and NOT the LIFT CORDS.
Slide tassle off cord
2g. Gently pry away the tilt mechanism, as shown, then remove it along with the tilt cords. NOTE: A screwdriver may be helpful in prying
away the tilt cords mechanism.
Pull cords out through holes in headrail

EN
11
2h. Insert the matching tilt rod adaptor into the motor (the one you set aside in Step 2b). NOTE: Insert the tilt rod adaptor into the side of the
motor with the grooved opening.
Tilt rod adaptor
Somfy Clever motor
2i. Attach the two headrail adaptors to the motor (the pair you set aside in Step 2a). Feed the motor wires through the gap in the adaptor.
NOTE: Attach the headrail adaptors in the same orientation as shown, fitting each securely onto the connector points on the motor.
Wires should pass through headrail adaptor as shown.
Make sure wires are not pinched.
Somfy Clever motor
Headrail adaptor
Headrail adaptor

EN
12
IMPORTANT At this point, you will need to determine if there is enough room to install the motor on the end
of the headrail, or if it needs to be installed in the center.
If the distance between the end of the headrail to the edge of the tilt tumbler is 5 inches (127mm) or more, follow
the instructions for an end-mount installation (Step 3).
If the distance is shorter than 5 inches (127mm) proceed to Step 4 for a center-mount installation.
Also, ensure that the tilt rod will pass through the full length of the motor assembly before proceeding.
5” (127mm)
or more
less than
5” (127mm)
END-MOUNT INSTALLATION
CENTER-MOUNT INSTALLATION
EN

EN
13
STEP 3END-MOUNT INSTALLATION NOTE Skip this step if performing a center-mount installation.
CAUTION Headrail edges may be sharp, so take care when working with it.
3a. Carefully slide the motor into the headrail from one end. Then slide the tilt rod into the tilt rod adaptor. NOTE: If the tilt rod doesn’t
extend through the motor, reverse it.
3b. If previously removed, re-install the C-Clip or retaining device to the tilt rod.
3c. Replace the end caps.

EN
14
STEP 4CENTER-MOUNT INSTALLATION NOTE Skip this step if performing an end-mount installation.
CAUTION Headrail edges may be sharp, so take care when working with it.
4a. Carefully slide the tilt rod out of one tilt tumbler to expose center of the headrail and to make room for insertion of the motor.
4b. Carefully position the motor in the headrail between the two tilt tumblers.
HELPFUL TIP: Inserting the motor (with one headrail adaptor attached) on an angle will help make this process easier. Then attach the
second headrail adaptor onto the other side of the motor. Make sure that both adaptors are securing the motor firmly within the headrail.

EN
15
4c. Insert the tilt rod into the motor housing. Make certain the tilt rod is inserted through the motor rod adaptor, and tilt tumbler.
NOTE: Make sure both (or all) tilt tumblers are oriented in the same position at this step to ensure even tilting and to prevent damage.
4d. If previously removed, re-install the C-Clip or retaining device to the tilt rod.

EN
16
STEP 5FINISHING UP
5a. Follow the instructions included with the battery pack or battery tube.Prepare and secure the battery tube or pack
to the window frame or wall using the included clips and hardware. Then attach the battery connector to the motor connector.
NOTE: Make sure that the battery pack has a full charge (rechargeable battery pack) or use new AA batteries (battery tube).
Li-Ion Rechargeable Battery Pack 12V Battery Tube (8AA Lithium)
IMPORTANT Do not disconnect the battery or power supply while the motor is operating. The motor’s power-supply
cable cannot be removed or replaced. If it is damaged, please contact Somfy.
5b. Rehang the blind by sliding it back into the open brackets, then snap both brackets closed. Replace any valance or decorative
covering, if used. NOTE: Lower the blind manually before programming the remote (Step 6).
Visit somfysystems.com/clever for additional support with power & control.

EN
17
STEP 6SETUP OF HAND-HELD REMOTE CONTROL
IMPORTANT The following instructions are for the setup and operation of a Somfy control device.If another control
device is to be used, follow the instructions provided with that control device.
BEFORE YOU BEGIN
Press any button on the remote to ensure that the LED indicator on the front of the remote illuminates. If the LED does not illuminate,
contact Somfy.
SITUO 1 RTS SITUO 5 RTS SITUO 5
VARIATION RTS
REMOTE CONTROL OPTIONS
Up
Down
my/stop Scroll wheel
LED indicator

EN
18
PROGRAM THE REMOTE
IMPORTANT On each of the following steps, be sure to read the entire step before performing it.
6a. The remote control has three buttons: UP , DOWN , and “MY” . To program the remote, press the UP and DOWN buttons
simultaneously. The blind slats will briefly tilt up and down to acknowledge communication between motor and remote control.
Brief tilt
up & down
6b. Test that the remote is properly communicating to the blind by pressing and holding the UP button ; the blind slats should tilt upward.
If the blind slats move (tilt) downward, press and hold the MY button until slats briefly tilt up and down. Blinds slats should now move up
when pressing and holding the UP button .
Brief tilt
up & down