SOMFY ROLLECTRIC II User manual

46
Technique The electric roller blind for simply
assembly. Completely ready for instal-
lation, with head profile and clips. Tube
of approx. 36 mm diameter. Motor
arrangement right or left. Length of
electric cable: 250 cm
Motor 24-Volt DC motor
Minimum voltage: 20 volt
Nominal current: 0.5 ampere
Maximum number of rotations: 40
Nominal rotation speed:
35 rotations/minute
With overload protection
Pay attention to the wire cross section
Colours Standard anodized aluminium/grey
Standard white RAL 9016
Other colours upon inquiry
Bottom bar RO Bottom weight aluminium
Colours Standard anodized aluminium/grey
Standard white RAL 9016
Other colours upon inquiry
Bottom bar SL Weight flat-profile aluminium
Colours Standard anodized aluminium/grey
Standard white RAL 9016
Other colours upon inquiry
Bottom bar TEX Weight flat-profile, 6 x 20 mm,
sewn into the seam
Option:
ELOX 1
Design
High-quality side cover on top and
caps RO and SL weight in anodized
aluminium, to match the anodized
aluminium head profile/bottom bar,
instead of the plastic option
36 mm
62 mm
24 mm
max. approx. 54 mm
25 mm
10 mm
Ø 24 mm
30 mm
8 mm
RO SL
TEX
8
XX / 2011
ELOX
ROLLECTRIC II
TECHNIQUE MOTOR 24 V

47
systems | ROLLER BLINDS
ROLLECTRIC II
TECHNIQUE MOTOR 24 V
Operation/
Controller
Set A: Switch with integrated
transformer
(INIS DC) 230/24 volt
Colour: white
Set B: White pole reverser switch
230/24 volt transformer
with 230 volt cable/connector
as well as 24 volt cable
For on site socket
Set M: Radio receiver set (DC-RTS)
24 volt white version with
1 channel white radio
hand-held transmitter
(Telis 1 RTS)
and 230/24 volt
transformer with 230 volt
cable/connector and 24 volt
cable
Group control Group controls as of two installations
upon inquiry
24 V
Set A
80 mm
80 mm
27 mm
230 V
24 V
47 mm
24 V
86 mm
42 mm
Set M
24V
25 mm
150 mm

48
Stopper Setting up of upper and lower limit
stop at the factory, fine adjustment on
site possible
Assembly and
disassembly of
the tube
Positioning the blind tube in the sup-
port:
1. First, position the tube in the
corresponding support.
2. Press the opposite side with the
attached clip into the round pin and
engage it.
3. Carry out fine adjustment if
necessary.
4. Place the cover on to the support
Size of system Maximum width of 200 cm
Maximum height of 300 cm
Fabric reeling Standard backward reeling,
forward reeling upon inquiry
Fabric width Roller blind width: ./. 3,4 cm
ROLLECTRIC II
TECHNIQUE MOTOR 24 V
Width of the roller blind system
Fabric width
approx. 12 mm approx. 22 mm

49
systems | ROLLER BLINDS
Clip
Standard
Colours
We deliver the roller blinds assembled,
together with the corresponding metal
clips.
Position the clips/supporting brackets
at approx. 4 to 6 cm from the end of
the blind.
Up to 99 cm width: 2 pieces
As of 100 cm up to 149 cm width: 3 pieces
As of 150 cm up to 199 cm width: 4 pieces
Standard nickel-plated
Standard white RAL 9016
Other colours upon inquiry
Rapid and simple fixing with a
shadow gap of approx. 7 mm
Supporting
bracket
Colours
Metal supporting bracket
Standard nickel-plated
Standard white RAL 9016
Other colours upon inquiry
Projection A approx. 50 mm
Projection B approx. 63 mm
Distance plate by
clip installation
Plastic distance plate transparent,
small projection distance from
wall thanks to the installation of one or
several distance plates
ROLLECTRIC II
INSTALLATION
8 mm 10 mm
18 mm 26 mm 34 mm
50 mm
24 mm
50 mm
68 mm
25 mm
32 mm
27 mm
B
A
B
A
7 mm
50 mm
68 mm
25 mm
32 mm
27 mm
B
A
B
A
7 mm
50 mm
25 mm
7 mm

50
ROLLECTRIC II
INSTALLATION
Function clip Insert the head profile into the clips
and press. The roller blind will engage
and be ready for use
Remove the blind by pressing the
«Push» button
The clips shall be fixed straightened to
the ceiling or the wall
Tension jack
Colours
We can deliver the blinds ready for
installation, including the corre-
sponding tension jacks upon inquiry
Standard nickel-plated
Minimum shadow gap of
approx. 2 mm
Positioning of the tension jack at
approx. 4 to 6 cm from the end of the
blind
Function
Tension jack
Up to 99 cm width: 2 pieces
As of 100 cm up to 149 cm width: 3 pieces
As of 150 cm up to 199 cm width: 4 pieces
Cable guide set
only
Bottom bar RO
Colours
Set consists of:
2 cable profile guides
2 cables (plastic-sheathed)
length A = 350 cm, B = 450 cm
2 cable guide clips
2 stretching devices
2 wall holders
Standard grey
Standard white
36 mm
36 mm

51
systems | ROLLER BLINDS
ROLLECTRIC II
INSTALLATION
Installation procedure:
1. Fix the cable profile clips to the head
profile by means of clamping screws
2. Fix the blind to the ceiling
3. Fix the cable guide clips to the
bottom bar
4. Pull through the metal cable, fix the
covering cap of the stretching device
to the cable
5. Fix the stretching device, stretch and
cover
Groove
Clip/tension jack
Installation of the blinds in the groove
Groove
Cable guide
Installation of the blinds in the groove
approx.
85 mm
approx. 78 mmapprox. 115 mm
approx. 115 mm
approx. 95 mm

72
When you place your order, please
indicate the measurements of the roller
blinds and use our order form
A – Blind width
(niche width + 10 cm)
B – Blind height
(niche height + 10 cm)
MEASURING AND INSTALLATION
IN FRONT OF THE NICHE
A
B
A
B
B
B
A
B
A
B
B
B

73
systems | ROLLER BLINDS
When you place your order, please
indicate the measurements of the roller
blinds and use our order form
A – Blind width
(niche width ./. 1 cm)
B – Blind height
(clear niche height)
MEASURING AND INSTALLATION
IN THE NICHE
A
B
A
B
B
B
A
B
A
B
B
B