Sony BC05 User manual

BC05 Module Spec.
ShenzhenSynchronElectronicsCo.,Ltd. 2010.11
1.GeneralDescriptionandSpcification
1.1GeneralDescription
Thisproduct isaClass 2 SMTBluetoothModuleused CSR BC5-MultiMedia
External. Itprovidesdata and voice communications. Itinterfaceswithahostthrough
USB or UARTand supportdata rate up to12M/3Mbps.
GeneralFetures:
Class 2 BluetoothModule
BluetoothSpec. V2.1+EDR Compliant
SupportFirmwareUpgrade
USB 2.0 and UARTHostInterface
Multi-ConfigurableI2S, PCMor SPDIFInterface
Integrated 1.5Vand 1.8VLinear Regulators
Integrated Switched-modeRegulator
Integrated BatteryCharger
Integrated Microphonebias&LEDDriver
64MIPS KalimbaDSP Co-processor
Builtin16-bitStereoCodec- 95dB SNR for DAC
Enhanced Audibilityand NoiseCancellation
Supportfor 802.11 Co-existence
Green(RoHS Compliant)
1.2Device Details
Radio
CommonTX/RXterminal simplifiesexternal matching;eliminatesexternal antennaswitch
BISTminimisesproductiontesttime
Bluetoothv2.1+EDRspecificationcompliant
Transmitter
4dBmRFtransmit powerwithlevelcontrolfromonchip6-bit DACoveradynamicrange>30dB
Class 2andClass 3supportwithouttheneedforanexternal poweramplifierorTX/RXswitch
Receiver
Receiversensitivityof -70dBm

Integratedchannelfilters
Digital demodulatorforimprovedsensitivityandcochannelrejection
Real-timedigitisedRSSIavailableonHCI interface
FastAGCforenhanceddynamicrange
Baseband and Software
16Mbit external Flash
48Kbyteinternal RAM, allowsfull-speeddata transfer, mixedvoice/data andfull piconetsupport
Logicforforwarderrorcorrection, headererrorcontrol, access codecorrelation, CRC,
demodulation, encryptionbit stream generation, whiteningandtransmit pulseshaping
TranscodersforA-law, μ-lawandlinearvoice fromhostandA-law, μ-lawandCVSD voice
overair
PhysicalInterfaces
SPIwithclockspeedsup to64MHzinMastermodeand32MHzinSlavemode
I2C mastercompatibleinterface
UARTinterface withprogrammabledata rateup to3Mbits/swithanoptional bypass mode
USBv2.0interface
Bi-directional serial programmableaudiointerface supportingPCM, I2SandSPDIFformats
TwoLEDdriverswithfaders
KalimbaDSP
VerylowpowerKalimbaDSP co-processor, 64MIPS, 24-bit fixedpointcore
SBCdecodetakesapproximately4mWpowerconsumptionwhilestreamingmusic
Single-cycleMAC;24 x24-bit multiplyand56-bit accumulator
32-bit instructionword, dual 24-bit data memory
6Kx32-bit program RAM, 16Kx24-bit +12Kx24- bit data RAM
64-wordx32-bit program memorycachewhenexecutingfromFlash
StereoAudioCodec
16-bit internal stereocodec
Dual ADCandDACforstereoaudio
Integratedamplifiersfordriving16Ωspeakers;noneedforexternal components
Supportforsingle-endedspeakerterminationandlineoutput
Integratedlow-noisemicrophonebias
ADCsampleratesare8, 11.025, 16, 22.05, 32 and44.1kHz
DACsampleratesare8, 11.025, 12, 16, 22.05, 24, 32, 44.1and48kHz

AuxiliaryFeatures
Powermanagementincludesdigital shutdownandwake-up commandswithanintegrated
low-poweroscillatorforultra-lowpowerPark/Sniff/Holdmode
On-chipregulators:1.5Voutputfrom1.8Vto2.7Vinputand1.8Voutputfrom2.7Vto4.5Vinput
On-chiphigh-efficiencyswitched-moderegulator;1.8Voutputfrom2.7Vto4.4Vinput
Power-on-resetcell detectslowsupplyvoltage
10-bit ADCand8-bit DACavailabletoapplications
On-chipchargerforlithiumion/polymerbatteries
1.3Specification
Chipset CSRBC05 Multimedia
SpecificationVersion BluetoothV2.1+EDR
PowerClass Class 2
FrequencyBand 2400~2483.5MHz
Max.TxPower -6~+4dBm
RXSensitivity ＜-70dBm
Distance >10m(Noobstacle)
FlashSize 16M
PowerVoltage 3.3V
SupplyCurrent <40mA
Operation Temperature -10 ~+45 ℃
Dimension 32mm(L)x 13.5 mm(W) x 1.2mm(H)

2.PackageInformation
2.1PinoutDiagram
Figure1:BC05 ModulePinout(TopView)
2.2TerminalFunctions

PinName PinNumber Description
GND 1 Ground
PIO4 2
PIO5 3
PIO6 4
PIO7 5
PIO8 6
Programmableinput/outputline
AIO1 7
AIO0 8 Analogueprogrammableinput/output
RESET 9 SystemReset(LowActive)
GND 10 Ground
GND 11 Ground
PIO10 12
PIO11 13
PIO12 14
PIO13 15
Programmableinput/outputline
GND 16 Ground
VDD 17 PositivesupplyforSPI/PCMportsandPIO[15:4]
andBC05 MM FlashPads, Connectto3.3V
GND 18 Ground
VDD_Flash 19 PositivesupplyforFlashMemory,Connectto3.3V
VDD_USB 20 PositivesupplyforUART/USBports
+1.8V 21 Switch-modepowerregulatoroutput
GND 22 Ground
USB_DP 23 USBdatapluswithselectableinternal1.5k Ω
pull-up resistor
USB_DN 24 USBdataminus
WP# 25 Flashwriteprotect(LowActive)
GND 26 Ground
UART_RX 27 UARTdatainput
UART_TX 28 UARTdataoutput
PCM_IN 29 Synchronousdatainput
PCM_SYNC 30 Synchronousdatasync
PCM_CLK 31 Synchronousdataclock
PCM_OUT 32 Synchronousdataoutput
SPI_CSB 33 ChipselectforSPI, activelow
SPI_MOSO 34 SPIdataoutput
SPI_CLK 35 SPIclock

SPI_MOSI 36 SPIdataintput
VRE_IN 37 Takehightoenablehigh-voltagelinearregulator
andswitch-moderegulator
VDD_BAT 38
Lithiumion/polymerbatterypositiveterminal.
Batterychargeroutputandinputtoswitch-
mode
regulator
GND 39 Ground
VDD_CHG 40 Batterycharge
LED1 41
LED0 42 LEDDriver
GND 43 Ground
SPK_L_N 44 Speakeroutputnegative, left
SPK_L_P 45 Speakeroutputpositive, left
SPK_R_N 46 Speakeroutputnegative, right
SPK_R_P 47 Speakeroutputpositive, right
GND_S 48 SignalGround
MIC_BIAS 49 Microphonebias
MIC_B_P 50 Microphoneinputpositive, right
MIC_B_N 51 Microphoneinputnegative, right
MIC_A_P 52 Microphoneinputpositive, left
MIC_A_N 53 Microphoneinputnegative, left
GND 54 Ground
PIO0 55
PIO1 56
PIO2 57
PIO3 58
Programmableinput/outputline
GND 59 Ground
RF 60 Transmitteroutput/switchedreceiverinput
2.3PackageDimensions

Figure2:BC05 ModulepackageDimensions

3.HardwareDescription
3.1BlockDiagram
Figure3:BC05 ModuleBlockDiagram
3.2RFPorts

Figure4:RFPortsDiagram
RF_NandRF_Pformacomplementarybalancedpairandareavailableforboth
transmitandreceive. Ontransmittheiroutputsarecombinedusinganexternalbalun
intothesingle-endedoutputrequiredfortheantenna. Similarly, onreceivetheirinput
signalsarecombinedinternally. Bothterminalspresentsimilarcompleximpedances
thatmayrequirematchingnetworksbetweenthemandthebalun.
AnLCnetwork, L4andC17.ThisprovidesaDCbiasfortheBlueCore5-MM
fromthe1.5Vrail.
TheBPF1usedtosuppress thesignaloutofBluetoothFrequencyBandand
enhance theEMCcapacity.
TheDClevelmustbesetatVDD_RADIO.
3.3UARTPorts
BC05 ModuleUARTinterface providesasimplemechanismforcommunicating
withotherserialdevicesusingtheRS232 protocol.WhenBlueCore5 Multimedia
Externalisconnectedtoanotherdigitaldevice, UART_RXandUART_TXtransfer
databetweenthetwodevices.
TheBaud rateoftheUARTports:
1200 baud ( 2%Error)
Minimum 9600 baud ( 1%Error)
Baud rate
Maximum 4Mbaud ( 1%Error)
3.4USBPorts

Thisisafull speed(12Mbits/s)USBinterface forcommunicatingwithother
compatibledigitaldevices.BC05 ModuleactsasaUSBperipheral, respondingto
requestsfromamasterhostcontrollersuchasaPC.
AsUSBisamaster/slaveorientedsystem(incommonwithotherUSB
peripherals), BlueCore5 MultimediaExternalonlysupportsUSBSlaveoperation.
4. GreenProducts andRoHSCompliance
5. Reference
1)BlueCore5-MultimediaExternalProductDataSheet, CS-101568-DSP4(bc05-ds-
004P)
2)SpecificationoftheBluetootnSystem, Verion2.1+EDR

FCC Statement
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant
toPart15 oftheFCC Rules.Theselimitsaredesignedtoprovidereasonableprotection againstharmful
interferenceinaresidentialinstallation.Thisequipmentgenerates,usesand can radiateradiofrequency
energyand,ifnotinstalledandusedinaccordancewiththeinstructions, maycauseharmfulinterference
toradiocommunications. However, thereisno guarantee that interferencewill not occurinaparticular
installation. If thisequipment does
causeharmfulinterferencetoradioortelevision reception, whichcan bedeterminedbyturning
theequipment off and on, theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthe
following measures:
Reorient orrelocatethereceiving antenna.
Increasetheseparation betweentheequipment and receiver.
Connect theequipment intoan outlet on acircuit different fromthat towhichthereceiveris
connected.
Consult thedealeroran experiencedradio/TVtechnician forhelp.
FCC Radiation Exposure Statement
Thisequipment complieswithFCC radiation exposurelimitsset forthforan uncontrolledenvironment.
1. ThisTransmittermust not beco-locatedoroperating inconjunction withanyotherantenna or
transmitter.
2. Thisequipment complieswithFCC RFradiation exposurelimitsset forthforan uncontrolled
environment. Thisequipment shouldbeinstalledand operatedwithaminimumdistanceof 20
centimetersfromuserand bystanders.
ThisequipmentcomplieswithPart15 of theFCC Rules.Operationissubjecttothefollowingtwo
conditions:(1) Thisdevice maynotcauseharmfulinterference, and(2) Thisdevice mustacceptany
interference received, includinginterference that maycauseundesiredoperation.
Caution!
The manufacturerisnot responsibleforanyradioorTVinterferencecaused byunauthorized
modificationstothisequipment. Suchmodificationscouldvoidthe userauthoritytooperate
the equipment.
CanadaICstatements:
ThisdevicecomplieswithIndustry Canada licence-exempt RSS-210. Operation issubject to
the following twoconditions: (1)thisdevicemaynot causeinterference, and (2)thisdevice
mustacceptanyinterference,includinginterferencethatmaycauseundesired operation ofthe
device.

Le pr sent appareil est conformeauxCNR d'IndustrieCanada applicablesauxappareilsradio
exemptsde licence. L'exploitation est autoris eauxdeuxconditionssuivantes: (1)l'appareil
ne doit pasproduirede brouillage, et (2)l'utilisateurde l'appareil doit acceptertout brouillage
radio lectrique subi, mêmesilebrouillage est susceptibled'en compromettrele
fonctionnement.
The devicemeetsthe exemption fromthe routine evaluation limitsinsection 2.5ofRSS 102
and compliancewithRSS-102 RF exposure, userscan obtainCanadian information on RF
exposureand compliance.
Le dispositifrencontrel'exemption deslimitescourantesd' valuation danslasection 2.5de
RSS 102 et laconformit àl'exposition de RSS-102 rf, utilisateurspeut obtenirl'information
canadienne surl'exposition et laconformit de rf.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment
Remark:
The end device which install this module should indicate the information
"ContainFCC ID:AK8BTMS3"or "Contain IC:409B-BTMS3"on the label
of the end device

BTMS3 Install manual
Fix main board on Rear cabinet by screws.
BT module
BT Antenna
Main board test Pass.
Fix the front, rear,top,bottom cabinet by screws.
BT module Location
BT module and Antenna
BT module Location
Main board test Pass.