Sony DPP-FP97 User manual

4-129-103-11 (4)
Digital Photo
Printer
DPP-FP97
© 2009 Sony Corporation
Before you begin
Preparations
Direct printing
Printing from a PictBridge
digital camera
Printing from a Bluetooth-
compliant device
Printing from a PC
Error messages
Troubleshooting
Additional information
D:\Printer\DPP-FP97 series 2008\IM\4129103112DPPFP97IM_GB\4129103114\4129103114DPPFP97IM_GB\010COV.fm
Master: Right
DPP-FP97 4-129-103-11 (4)
Operating Instructions
Before operating this unit, please read “Read This First” and
“About the Print Packs” supplied and this manual, “Operating
Instructions,” thoroughly and retain them for future reference.
Owner's Record
The model and serial numbers are located on the bottom of the
printer. Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony
dealer regarding this product.
Model No.: DPP-FP97
Serial No. ________________________
Please read the supplied “Read This First”
and “About the Print Packs.”
010COV.fm Page 1 Thursday, February 12, 2009 5:18 PM

2 GB
WARNING
To reduce fire or shock hazard, do not
expose the unit to rain or moisture.
For the customers purchasing
the DPP-FP97 in the U.S.A.
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
If you have any questions about this product, you may
call:
Sony Customer Information Services Center
1-800-222-SONY (7669)
The number below is for the FCC related matters
only.
Regulatory Information
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
For the Customers in Europe
This product has been tested and found compliant
with the limits set out in the EMC Directive for using
connection cables shorter than 3 meters (9.8 feet).
Attention
The electromagnetic fields at the specific frequencies
may influence the picture of this digital photo printer.
Notice
If static electricity or electromagnetism causes data
transfer to discontinue midway (fail), restart the
application or disconnect and connect the
communication cable (USB, etc) again.
Notice for the customers in the
countries applying EU Directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo,
108-0075 Japan.
The Authorized Representative for EMC and product
safety is Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters, please refer to
the addresses given in separate service or guarantee
documents.
Declaration of Conformity
Trade Name: SONY
Model No.: DPP-FP97
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.

3 GB
Disposal of Old Electrical &
Electronic Equipment (Applicable in
the European Union and other
European countries with separate
collection systems)
This symbol on the
product or on its
packaging indicates that
this product shall not be
treated as household
waste. Instead it shall be
handed over to the
applicable collection
point for the recycling of
electrical and electronic
equipment. By ensuring
this product is disposed
of correctly, you will
help prevent potential
negative consequences for the environment and
human health, which could otherwise be caused by
inappropriate waste handling of this product. The
recycling of materials will help to conserve natural
resources. For more detailed information about
recycling of this product, please contact your local
Civic Office, your household waste disposal service
or the shop where you purchased the product.
NOTICE FOR CUSTOMERS IN
THE UNITED KINGDOM
A moulded plug complying with BS 1363 is fitted to
this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be
replaced, a fuse of the same rating as the supplied one
and approved by ASTA or BSI to BS 1362,
(i.e.marked with or mark) must be used.
If the plug supplied with this equipment has a
detachable fuse cover, be sure to attach the fuse cover
after you change the fuse. Never use the plug without
the fuse cover. If you should lose the fuse cover,
please contact your nearest Sony service station.
Notes on LCD screen
• The displayed image on the screen is not identical in
picture quality and colors with the printed image
because display methods or profiles differ. Please
regard the displayed image as just a reference.
• Do not press against the LCD screen. The screen
may be discolored and that may cause a
malfunction.
• Exposing the LCD screen to direct sunlight for a
long period may cause malfunctions.
• The LCD screen is manufactured using extremely
high-precision technology, so over 99.99% of the
pixels are operational for effective use. However,
there may be some tiny black points and/or bright
points (white, red, blue or green in color) that
constantly appear on the LCD screen. These points
are normal in the manufacturing process and do not
affect the printing in any way.
• Images may trail across on the LCD screen in a cold
location. This is not a malfunction.
Duplication, edition, or printing of a CD, TV
program, copyrighted materials such as pictures or
publications, or any other materials except for your
own recording or creation is limited to private or
domestic use only. Unless you hold copyright or
have permission from copyright holders for the
materials to be duplicated, use of those materials
beyond this limit may infringe the provisions of the
copyright law and be subject to the copyright
holder’s claim for damages.
When using photo images with this printer, pay
special attention not to infringe the provisions of
the copyright law. Any unauthorized use or
modification of portraits may also infringe their
rights.
For some demonstrations, performances, or
exhibits, photography may be forbidden.
Backup recommendations
To avoid potential risk of data loss caused by
accidental operation or malfunction of the printer,
we recommend that you save a backup copy of
your data.
Information
IN NO EVENT SHALL SELLER BE LIABLE
FOR ANY DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY
NATURE, OR LOSSES OR EXPENSES
RESULTING FROM ANY DEFECTIVE
PRODUCT OR THE USE OF ANY PRODUCT.
Sony shall assume no responsibility for any
accidental or consequential damages or loss of the
recorded content which may be caused by use or
malfunction of the printer or memory card.
Continued

4 GB
On trademarks and copyrights
•“BRAVIA,”“BRAVIA” Sync, , Cyber-
shot, , “Memory Stick,” ,
“Memory Stick Duo,” ,
“MagicGate Memory Stick,” “Memory Stick PRO,”
, “Memory Stick PRO
Duo,” , “Memory Stick
PRO-HG Duo,” ,
“Memory Stick Micro,” ,
, “Memory Stick-ROM,” ,
“MagicGate,” and are
trademarks of Sony Corporation.
• HDMI, , and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
• Microsoft, Windows, Windows Vista and DirectX
are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or
other countries.
• Intel and Pentium are the registered trademarks or
trademarks of Intel Corporation.
• CompactFlash is a trademark of SanDisk
Corporation in the U.S.A.
• or xD-Picture Card™ is a trademark of
FUJIFILM Corporation.
• is a trademark of FotoNation Inc. in the
U.S.A.
• is a registered trademark of
Ichikawa Soft Laboratory.
• All other companies and product names mentioned
herein may be the trademarks or registered
trademarks of their respective companies.
Furthermore, “™” and “®” are not mentioned in
each case in this manual.
• This unit is equipped with face recognition feature.
Sony Face Recognition technology developed by
Sony is used.
• The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Sony Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
• Other trademarks and trade names are those of their
respective owners.
•Zlib
© 1995- 2002 Jean-loup Gailly and Mark Adler
• Contains iType™ and fonts from Monotype
Imaging Inc.
iType™ is a trademark of Monotype Imaging Inc.
Notice for users
Program © 2009 Sony Corporation
Documentation © 2009 Sony Corporation
All rights reserved. This manual or the software
described herein, in whole or in part, may not be
reproduced, translated or reduced to any machine
readable form without prior written approval from
Sony Corporation.
IN NO EVENT SHALL SONY CORPORATION BE
LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES,
WHETHER BASED ON TORT, CONTACT, OR
OTHERWISE, ARISING OUT OF OR IN
CONNECTION WITH THIS MANUAL, THE
SOFTWARE OR OTHER INFORMATION
CONTAINED HEREIN OR THE USE THEREOF.
By breaking the seal of the envelope of the CD-ROM
package, you accept all the terms and conditions of
this agreement. If you do not accept these terms and
conditions, please return this disk envelope unopened,
along with the rest of the package, immediately to the
dealer where you obtained it.
Sony Corporation reserves the right to make any
modification to this manual or the information
contained herein at any time without notice.
The software described herein may also be governed
by the terms of a separate user license agreement.
Any design data such as sample pictures provided in
this software cannot be modified or duplicated except
for the purpose of personal use. Any unauthorized
duplication of this software is prohibited under
copyright law.
Please note that unauthorized duplication or
modification of portraits or copyrighted work could
infringe the rights reserved by rights holders.
You may be referred to the supplied “Read This
First” and “About the Print Packs” when there are
detailed explanations in the leaflet.

5 GB
Table of Contents
Notice for users ..............................4
Before you begin
Identifying the parts ........................7
Preparations
Checking the contents of the
package ..........................................9
Setting the ink ribbon .....................9
Inserting the print paper ...............10
Connecting to the AC power
source ..........................................12
Operations in the initial state ..........13
Direct printing
LCD screen display .......................14
An image preview view ...................14
Index View ......................................15
Basic printing ...............................16
Inserting a memory card .................16
Printing selected images ................17
Enjoying various printing ..............18
Correcting a failed photo automatically
(AUTO TOUCH-UP) ........................ 20
Editing an image ...........................21
Enlarging and reducing an
image size ......................................21
Moving an image ...........................21
Rotating an image ..........................21
Adjusting an image ........................22
Adding a special filter to an image . 22
Correcting the red-eye
phenomenon .................................. 24
Printing an edited image ................ 25
Saving an edited image .................. 25
Performing “CreativePrint” ...........26
Making a Scrapbook ...................... 26
Making a Calendar ......................... 29
Superimposing a Handwritten
message, Stamp or Preinstalled phrase
on an image ................................... 31
Adding a Frame .............................. 33
Making a Layout print .................... 33
Making an ID Photo ....................... 34
Performing Batch Print (Index Print/
DPOF Print/Print All) .....................35
Viewing a Slideshow .....................36
Showing a Slideshow ..................... 36
Reserving printing .......................... 36
Printing .......................................... 36
File operations ..............................37
Copying images ............................. 37
Deleting selected images ............... 38
Formatting a “Memory Stick”
media ............................................. 38
Formatting the internal memory ..... 39
Changing the Print setup ..............39
Making a Date Print ....................... 40
Changing the Display/Printer
setup ............................................43
Continued

6 GB
Connecting to a High Definition
television and Printing ..................45
Connecting to a television ............. 45
Printing procedures ....................... 46
Using the printer buttons for
printing .......................................... 46
Using the television remote control
unit for printing .............................. 46
Printing from an external device ...48
Printing from a PictBridge
digital camera
Printing from a PictBridge digital
camera .........................................49
Printing from a Bluetooth-
compliant device
Printing from a Bluetooth-compliant
device ...........................................50
Compatible profiles for Bluetooth
communication .............................. 50
Preparations: connecting
DPPA-BT1 ..................................... 50
Printing .......................................... 50
Transferring an image to a memory
card ............................................... 51
Printing from a PC
Printing from a PC ........................52
Installing the software ..................52
System requirements ..................... 52
Installing the printer driver ............. 53
Installing the PMB (Picture Motion
Browser) ........................................ 55
Printing photos from the PMB
(Picture Motion Browser) .............56
Registering a browsing folder .........60
Printing from a commercially available
software application ........................60
Error messages
If an error message appears .........62
Troubleshooting
If trouble occurs ...........................65
If paper jams ................................76
Cleaning .......................................77
Additional information
Precautions ..................................78
On safety ........................................78
On installation ................................78
On cleaning ....................................79
On restrictions on duplication ........79
When disposing of the printer ........79
About the Memory Cards ..............79
“Memory Stick” media ....................79
SD memory Card ............................80
xD-Picture Card ..............................81
CompactFlash card .........................81
Notes on using memory card ..........81
Specifications ...............................82
Printing range .................................84
Glossary .......................................85
Index ............................................86

7 GB
Before you begin
Before you begin
Identifying the parts
For details, see the pages indicated in the
parentheses.
Printer front panel
A1(on/standby) button/standby
indicator)
BMENU button
C(Index View) (zoom out)/
(zoom in) buttons (.page 16)
DLCD screen
EENTER button
FDirection (g/G/f/F) buttons
GAUTO TOUCH-UP button
(.page 20)
HPRINT button/indicator
ICANCEL button
J“Memory Stick PRO” media
(Standard/Duo) slot (.pages 16,
79)
KSD memory Card/xD-Picture Card
dual-format slot (.pages 16, 80,
81)
LCompactFlash card slot
(.pages 16, 81)
MPaper tray compartment door
NPaper tray compartment
(.page 11)
OAccess indicator
PInk ribbon eject lever (.page 9)
QInk ribbon (sold separately)
(.page 9)
RInk ribbon compartment door
(.page 9)
Continued

8 GB
Printer rear panel
AHandle
As illustrated below, raise the handle when
you carry the printer.
When you use the printer, close the handle to
its original position.
Notes
• When you carry the printer, make sure to
remove memory cards, external devices,
the paper tray, AC adaptor, and other
cables. Otherwise malfunctions may occur.
• Set the LCD panel to its original position.
BVentilation holes
CPaper outlet
DDC IN 24 V jack (.page 12)
Plug the supplied AC adaptor into this
connector. Then connect the AC adaptor and
AC outlet with the power cord.
Printer left side panel
EHDMI OUT (output) connector
(.page 45)
When using the printer with a High-definition
television, connect an HDMI cable into this
connector.
FUSB connector (.page 54)
When using the printer in PC mode, connect a
USB cable to this connector.
GPictBridge/EXT INTERFACE
connector (.pages 48 to 50)
When using a PictBridge-compliant digital
camera, a mass storage device such as a USB
memory or photo storage device, a Bluetooth
USB adaptor (DPPA-BT1*), or other external
USB device, connect it via this connector.
* In some regions, the DPPA-BT1 Bluetooth
USB adaptor is not sold.

9 GB
Preparations
Preparations
Checking the contents
of the package
Make sure that the following accessories are
supplied with your printer.
• Paper tray (1)
• AC adaptor (1)
• AC power cord*1 (1)
• USB cable (1)
• Cleaning cartridge (1)/Cleaning sheet (1)
• CD-ROM (Windows Printer Driver Software
Ver.1.0 and PMB (Picture Motion Browser)
Ver.4.2) (1)
• Operating Instructions (this booklet) (1)
• Read This First (1)
• About the Print Packs (1)
• Warranty (In some regions, the warranty is
not supplied.) (1)
• Sony End User Software License Agreement
(1)
*1 The plug shape and specifications of the AC power
cord differ depending on the region in which you
purchased the printer.
About Sony Print Packs (sold
separately)
Please use a Sony optional color print pack
designed for the printer. For details, refer to the
supplied “About the Print Packs.”
Setting the ink ribbon
1Pull and open the ink ribbon
compartment door.
2Insert the ink ribbon in the direction
of the arrow until it clicks into place.
3Close the ink ribbon compartment
door.
Removing the ink ribbon
Push up the blue eject lever, and remove
the used ink ribbon.
Continued

10 GB
Notes
• Do not touch the ink ribbon or store the ink ribbon
in a dusty location. Fingerprints or dust on the ink
ribbon may result in imperfect printing.
• Do not rewind the ink ribbon and use the rewound
ink ribbon for printing. Otherwise, proper printing
results will not be obtained, or a malfunction may
occur. If the ink ribbon does not click into place,
remove it and then re-insert it. Only when the ink
ribbon is too slack to be loaded, keep pressing the
core of the ribbon and wind the ink ribbon in the
direction of the arrow to remove the slack.
• Do not disassemble the ink ribbon.
• Do not pull out the ribbon from the ink ribbon.
• Do not remove the ink ribbon while printing.
• Avoid placing the ink ribbon in a location subject
to high temperatures, high humidity, excessive
dust or direct sunlight. Please store it in a cool and
dark place and use it within a short period from the
date of production. Depending on the storage
conditions, the ink ribbon may deteriorate. Use of
such an ink ribbon may affect the printed results,
for which we cannot guarantee or compensate.
Inserting the print paper
1Open the paper tray cover.
Hold the parts on both sides of the paper
tray cover (shown with arrows) and open
the paper tray cover.
2Set the print paper into the paper
tray.
Do not wind the
ribbon in the
directions shown
here.

11 GB
Preparations
3Close the paper tray cover.
4Open the slide cover.
5Insert the paper tray into the printer.
Notes
• You can set up to 20 sheets of print paper. Riffle
the print paper thoroughly. Insert the print paper
with the protective sheet facing up. Remove the
protective sheet from the tray.
• If there is no protective sheet, insert the print paper
into the paper tray with its printing surface (the
side with no imprint) facing up.
• Do not touch the printing surface. Fingerprints or
contamination on the printing surface may result in
imperfect printing.
• Do not bend the print paper, or cut the print paper
from the perforations before printing.
• To avoid paper jam or malfunctions of the printer,
make sure of the following before printing:
– Do not write or type on the print paper.
– Do not attach a sticker or stamps on the print
paper.
– When adding print paper to the paper tray, be
sure that the total number of print paper sheets
does not exceed 20 sheets.
– Do not insert different types of print paper
together into the paper tray.
– Do not print on used print paper. Printing an
image twice on the same paper will not make
the printed image thicker.
– Use the print paper for this printer only.
– Do not use print paper ejected without printing.
Notes on storing the print paper
• To store print paper in the tray, remove the paper
tray from the printer and close the slide door of the
paper tray.
• Avoid storing the paper with the printed faces
touching each other or in contact with rubber or
plastic products, including vinyl chloride or
plasticizer for an extended period of time; color
changes or deterioration of the printed image may
occur.
• Avoid placing the print paper in a location subject
to high temperatures, high humidity, excessive
dust or direct sunlight.
• When you are going to store partially-used print
paper, store it in its original bag or a similar
container.

12 GB
Connecting to the AC
power source
1Insert the plug of the AC adaptor
into the DC IN 24 V jack on the back
of the printer.
2Connect one plug of the AC power
cord to the connector of the AC
adaptor and the other plug to the
wall outlet.
Notes
• Do not place the printer in an unstable location
such as on a wobbly table.
• Leave enough room around the printer. The print
paper emerges from the back a few times during
printing. Keep 10 cm (13/32 inches) or more space
at the rear of the printer.
• Connect the AC adaptor to an easily accessible
wall outlet close by. If trouble occurs while using
the adaptor, immediately shut off the power by
disconnecting the plug from the wall outlet.
• Do not short the plug of the AC adaptor with a
metallic object, as this may cause a malfunction.
• Do not use the AC adaptor placed in a narrow
space, such as between a wall and furniture.
• When you have finished using the AC adaptor,
disconnect the AC power cord from the
DC IN 24 V jack of the printer and from the AC
power sources.
• The printer is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the printer itself has been turned off.
• A socket outlet should be as close as possible to the
unit and easily accessible.
To use your Printer abroad -
Power sources
You can use your Printer and the AC Adaptor
(supplied) in any country or region where the
power supply is within 100 V to 240 V AC,
50/60 Hz.
Do not use an electronics transformer (travel
converter), as this may cause a malfunction.
AC adaptor
AC power cord
To the wall
outlet
10 cm
(13/32
inches)

13 GB
Preparations
When the photo printer is turned on without a
memory card inserted or an external device
connected, the initial display below appears on
the screen.
When the printer is not operated for 5 seconds,
demo mode is displayed. If any button other
than the 1(on/standby) button is pressed, the
screen returns to the initial display. If you press
ENTER, the images in the internal memory are
displayed.
If a memory card is inserted, or an external
device is connected, the images from the
memory card, the external device, or the
internal memory are displayed.
Perform operations according to the printing as
follows:
• To print directly from a memory card, an
external device, or the internal memory, see
page 16.
• To print from a PictBridge digital camera,
see page 49.
• To print from a Bluetooth-compliant device,
see page 50.
• To print from a PC, see page 52.
Operations in the initial state

14 GB
Direct printing
LCD screen display You can change the image preview view by
setting the “On-screen Display” (page 44) from
the Display/Printer setup menu.
To display a different image, press g/G.
AInput/setting indications
Input indications and settings information for
an image are displayed.
BNumber of selected images/Total
number of images
CInk ribbon indication
P: P size
C: Cleaning cartridge
An image preview view
On-screen Display: On
O
n-screen Display: Off
On-screen Display: Details
Icons Meaning
“Memory Stick” media input
CompactFlash card input
SD memory Card input
xD-Picture Card input
External Device input
Internal memory
Protect indication
DPOF print preset indication
Associated file indication
(Displayed when there is an
associated file such as a motion file
or a miniature e-mail image file.)
Indicates Date Print “On.”
Indicates Date Print (Date/Time)
“On.”
Indicates “Pattern 1” (Borders).
Indicates “Pattern 2” (Borders).
Indicates Pages Per Sheet 4 “On.”
Indicates Pages Per Sheet 9 “On.”
Indicates Pages Per Sheet 16
“On.”

15 GB
Direct printing
DImage number (folder-file
number)*
* DCF-compatible files only. In the case of
other file formats, only part of the file name
will be displayed.
EOperation tips
FShot or saved date
GPrint quantity set
HDetailed information display
Displays a list of the images contained on the
selected medium (Index View). You can switch
the index view by selecting “Number Order” or
“Shoot. Date” on the Index View menu.
Index View: “Number Order”
The images are listed in the order of their file
names.
Index View: “Shoot. Date”
The images are listed by their shooting or saved
date.
ACursor (orange frame)
You can move the cursor (selection) by
pressing g/G/f/F.
BPrint quantity set
COperation tips
DScroll bar
Indicates the location of the image among the
total number of images.
EShooting date
Note
When the number of images exceeds 2 000, the
images cannot be displayed by date. They are
displayed in Number Order.
Index View
Continued

16 GB
Basic printing
With the label side facing up, insert a
memory card (“Memory Stick” media,
“Memory Stick Duo” media, CompactFlash
card, SD memory Card or an xD-Picture Card)
that contains the images for printing into the
proper slot until firmly into place. For the types
of memory cards you can use with the printer,
please see pages 79 to 81.
Tip
To print an image in the internal memory, turn on the
printer, and press ENTER without a memory card
inserted or external device connected.
With the label side facing up (xD-Picture Card,
SD memory Card, CompactFlash card, or
“Memory Stick” media (“Memory Stick Duo”
media) from the left)
To eject a memory card
Remove the memory card from the slot slowly
in the reverse direction it was inserted.
Notes
• The printer supports both standard and small sizes
“Memory Stick” media. A “Memory Stick Duo”
media adaptor is not necessary.
• The SD memory Card/xD-Picture Card dual-
format slot automatically detects card type.
Switching the image preview
view and index view
You can switch the display as follows:
• To display the index view
In an image preview view, press
(Index View)/ (Reduce).
When an image is enlarged, press
/ , so that the image is reduced to
its original scale and then the index view
is displayed.
• To display an image preview view
In the index view, press g/G/f/Fto move
the cursor to the image whose preview
view you want to display and press
ENTER or (Enlarge).
Enlarging an image
Keep pressing (Enlarge). The image is
enlarged up to 5 times the original scale.
Inserting a memory card
A
ccess
i
n
di
cator

17 GB
Direct printing
This section explains how to display the images
of a memory card, an external device, or
internal memory on the printer’s LCD screen
and print the selected images (direct printing).
For how to print from an external device, see
page 48.
1Press 1(on/standby) to turn on the
printer.
The standby indicator of the printer lights
in yellow green. An image stored on the
memory card inserted or external device
connected is displayed on the LCD screen.
By pressing ENTER without a memory
card inserted or an external device
connected, you can display an image from
the printer’s internal memory.
2Press g/Gto display the image that
you want to print.
3Set the print quantity.
To print one sheet of the displayed image,
skip this procedure and go on to the next
step.
Press ENTER to display the print quantity
indication. Then press f/Fto specify the
number of copies and press ENTER.
4Press PRINT.
While the PRINT button lights in green,
the printer is ready for printing. All the
images with print quantity settings are
printed.
To print multiple images
Repeat steps 2 and 3.
To change the print quantity
Display the image whose print quantity
you want to change, and press ENTER to
display the print quantity indication. Then
press f/Fto set the print quantity and
then press ENTER.
If you select “0,” printing is canceled.
Notes
• Never move or turn off the printer while it is
printing; the ink ribbon may become stuck or paper
jam may occur. In case you turn off the power,
keep the paper tray inserted and turn on the printer.
After the paper is ejected, resume printing.
• Do not remove the paper tray during printing.
Otherwise, malfunction may occur.
• The print paper emerges a few times during
printing. Do not touch nor pull the emerged paper.
• If print paper is jammed, see page 76.
On selecting input
The printer is not equipped with the input select
switch. When you connect a memory card or an
external device with the printer, the images of
the connected memory card or external device
are displayed automatically. If multiple
memory cards or an external device are
connected, the media first connected has the
priority. The images in the internal memory are
displayed when you press ENTER without
inserting a memory card or connecting an
external device.
When you turn on the printer with multiple
media being inserted or connected, the printer
detects the media in the order of “Memory
Stick” media, CompactFlash card, SD memory
Card, xD-Picture Card, the external device
connected to PictBridge/EXT INTERFACE
connector, and the computer.
Printing selected images

18 GB
Enjoying various printing
You can adjust the size, position, hue or other picture property of the selected image.
Operation using the printer
buttons
Auto Touch-up adjustment
.page 20
In addition to the Auto Fine Print 6
automatic adjustment, the following
adjustments are performed:
• Red-eye Correction
• Exposure Correction (using face
detection feature)
• Focus Correction
• WB Correction
• Auto Dodging
• Skin Smoothing
• Press g/Gto select a desired item, and
then press ENTER.
• To exit the menu, press CANCEL or
MENU again.
AUTO TOUCH-UP
Press MENU.
1Edit .page 21
Items Procedures
/ Increases or reduces the size of an
image.
Moves an image.
Rotates an image.
Adjusts the picture quality of an
image.
Adds an filter to an image.
Reduces the red-eye phenomenon.
Undoes the editing just done and
resets the image to the status
before editing.
Saves the edited image.
Pressing the AUTO TOUCH-UP
button adjusts exposure, focus,
red-eye and other corrections
automatically.
Prints an edited image.
Exits the Edit menu.
Items Procedures

19 GB
Direct printing
You can create a Calendar, ID Photo, or other various printouts.
2CreativePrint .page 26
Scrapbook Calendar Superimpose
Frame Layout print ID Photo
3Batch Print .page 35
You can enjoy batch print such as
“Index Print,” “DPOF Print,“ and “Print
All.”
Index Print
4Slideshow .page 36
You can perform a slideshow of the images. You can also
perform a slideshow of the “CreativePrint” prints.
5Print setup 6Display/Printer setup
.page 39 .page 43
7File operation .page 37
• Copying images between memory cards
• Deleting an image
• Formatting a “Memory Stick” media or the “Internal
memory”

20 GB
Correcting a failed
photo automatically
(AUTO TOUCH-UP)
1Select the image that you want to
adjust and then press AUTO
TOUCH-UP.
Adjustment of the selected image starts.
The adjustment results will be displayed
on the screen. When a human face is
detected, the face is displayed with a
frame as the adjustments proceed.
To check the adjustment result
more clearly:
Press to enlarge the image. (The image
will not be enlarged when printed.)
To display the original image
(before adjustments) again
Press AUTO TOUCH-UP. To display the
adjusted image, press AUTO TOUCH-UP
again.
If you have set a print quantity for
multiple images
All the images with print quantity settings
are adjusted. To display other images,
press g/G.
To change the print quantity
Press ENTER to display the print quantity
indication. Then press f/Fto set the print
quantity and then press ENTER.
2Press PRINT.
Printing of the selected image(s) starts.
Saving a corrected image
Press MENU, and the confirmation dialog box
is displayed. Press g/Gto select “Yes,” and
then press ENTER. An adjusted image is saved
as a new file. (page 25)
Tip
Adjustment takes effect only on the image being
printed. The original image will not be adjusted.
Notes
• After the Auto Touch-up adjustment, you cannot
make a trimming print of an image that has been
enlarged by pressing .
• Depending on the image, the Auto Touch-up
adjustment may not take effect properly. In this
case, select “Adjust” from the Edit menu to adjust
the image quality manually (page 22).
• Do not remove the memory card or external device
during the Auto Touch-up adjustment.
• Depending on the condition of the image, the
correction may take some time.
The automatic red-eye
correction function of this
printer uses the technology of
FotoNation Inc. in the U.S.A.
The “Skin Smoothing,” “WB Correction,” and
“Auto Dodging” correction functions of the
printer use the technology of Ichikawa Soft
Laboratory.