Soundoff Signal ETSS100CBKDC15 User manual

1.800.338.7337 / www.soundo󰀨signal.com
CHARGER BUMPER SPEAKER BRACKET
ETSS100CBKDC15 (for 2015 - 2021 model years)
1ETSS100CBKDC15 0221
TECHNICAL SPECIFICATIONS
Material: Steel with powder coated black
nish
Dimensions
(bracket only):
11”H x 7.3”W x 4.5”D
BRACKET COMPATIBLE WITH SPEAKERS:
- 100C
- 100N
- 100J
WARNING
!
Sirens produce loud sounds that
may damage hearing
Roll up windows
Wear hearing protection
Use only for emergency response
Avoid exposure to siren sound
outside of vehicle
I
I
I
I
IMPORTANT
TO AVOID DAMAGE TO SPEAKER USE THE SUPPLIED PLASTIC WASHERS ON
BOTH SIDES OF METAL BRACKET. FOLLOW INSTRUCTIONS ON NEXT PAGE.
ASSEMBLY SHOWN IS REPRESENTATIVE ONLY. EACH SPEAKER
IS SLIGHTLY DIFFERENT AND INSTALLER IS RESPONSIBLE FOR
SECURE MOUNTING IN BRACKET.
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION

1.800.338.7337 / www.soundo󰀨signal.com
CHARGER BUMPER SPEAKER BRACKET
ETSS100CBKDC15 (for 2015 - 2021 model years)
2ETSS100CBKDC15 0221
3
SPEAKER BRACKET ASSEMBLY
FRONT BUMPER SHOWN ONLY
MARK THE PLASTIC SHELL OF THE
BUMPER AS SHOWN. NOTCH PLASTIC TO
ALLOW BUMPER TO BE REPOSITIONED
BACK ON VEHICLE WITH SPEAKER
BRACKET ASSEMBLY.
4
-ASSEMBLE AS SHOWN-
PARTS WILL VARY DEPENDING ON SPEAKER.
SEE STEP 5
SPEAKER
1REMOVE FRONT BUMPER COVER ASSEMBLY AS ONE PIECE AND NOT INDIVIDUALLY.
CONSULT A LOCAL CHRYSLER SERVICE CENTER FOR BEST DISASSEMBLY METHOD.
-KEEP ALL HARDWARE-
NOTE: OUTER BUMPER SHELL NOT SHOWN FOR CLARITY
2
POSITION SPEAKER BRACKET ON THE IMPACT
BAR SO THAT SPEAKER WILL FACE FORWARD.
BACK VIEW OF FRONT BUMPER ASSEMBLY
RECOMMENDED SPEAKER BRACKET LOCATIONS

1.800.338.7337 / www.soundo󰀨signal.com
CHARGER BUMPER SPEAKER BRACKET
ETSS100CBKDC15 (for 2015 - 2021 model years)
3ETSS100CBKDC15 0221
5100N HARDWARE
ITEM# DESCRIPTION
1 M6X30MM SS BOLT
2SS LOCK WASHER
3 SS WASHER
4 OUTER PLASTIC WASHER
5 INNER PLASTIC WASHER
6 0.5” PLASTIC SPACER
5
4
3
2
1
6
100J HARDWARE
ITEM# DESCRIPTION
1 M6X30MM SS BOLT
2SS LOCK WASHER
3 SS WASHER
4 OUTER PLASTIC WASHER
5 INNER PLASTIC WASHER
6 0.31” PLASTIC SPACER
100C HARDWARE
ITEM# DESCRIPTION
11/4” - 20X0.75” SS BOLT
2SS LOCK WASHER
3 SS WASHER
4 OUTER PLASTIC WASHER
5 INNER PLASTIC WASHER
6 NOT USED
IMAGE IS FOR REFERENCE ONLY

1.800.338.7337 / www.soundo󰀨signal.com
CHARGER BUMPER SPEAKER BRACKET
ETSS100CBKDC15 (for 2015 - 2021 model years)
4ETSS100CBKDC15 0221
7NOTE
VERIFY THE CORRECT HARDWARE IS BEING USED DEPENDING ON THE MODEL
SPEAKER LISTED ON PREVIOUS PAGE BEFORE PROCESSING TO NEXT STEP.
8WIRE SPEAKER TO SIREN OUTPUT AND TEST
9RE-INSTALL FRONT BUMPER COVER ASSEMBLY USING
PREVIOUSLY REMOVED HARDWARE
100N
IMPORTANT
HARDWARE SAME AS 100H SPEAKERS
*EXCEPT USE M6 BOLTS PROVIDED WITH KIT*