SRC BMW-R1200GS-01-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
No. Description Quantity Torque * (N-m) Remarks **
1 Head Light Guard 1
2 Bracket LH 1
3 Mounting Pin 4
4 Bracket RH 1
5 Grommet 4
6 Screw M6 x 16 2 10-12 Use Liquid Thread Locker
7 Screw M5 x 16 2 5 - 6 Use Liquid Thread Locker
8 Washer M6 2
9 Washer M5 2
SRC Design uses Metric System of Measurement and all dimensions are in Millimeters
* Recommended to use the Torque specified in the table
** Denotes Usage of Liquid Thread Locker in specified locations
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: BMW-R1200GS-01-01-SL / BMW-R1200GS-01-02
Part Description: Head Light Guard –BMW R1200 GS
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Mounting Instructions
Step
1:
The Mounting Holes marked in Red colour, will be exposed,
when the Windshield is removed, as shown.
Step 2:
Orient and align the Bracket LH (1), as shown, and slide-in the Mounting screws and washers as shown.
The
Mounting Hole on the Top side, accepts Screw M5 x 16 (7) –1 off and Washer M5 (9) –1 off, as shown.
The
Mounting Hole on the Side, accepts Screw M6 x 16 (6) –1 off and Washer M6 (8) –1 off, as shown.
Tighten it to
torque, as specified in the BOM table
. Mount the Mounting Pin (3) –2 off, to the Bracket (this can be done Off-line
too).
The Pin has threaded shank which can be screwed on to the Bracket.
Step 3:
Repeat the Step 2 for mounting
the Bracket RH (4), as shown.

Copyright By SRC
Design and Specification are subjected to change
Page 4
This drawing view shows the Mounted condition
of the Bracket LH and Bracket RH, with the
Mounting Pin.
Step 4:
Orient the Head Light Guard (1), as shown.
Assemble the Grommet (5) –4 off, hugging and
flush, with the outer surfaces of the Head Light
Guard and holding on to the Mounting Pins,
projecting out of the Bracket RH & Bracket LH
The Final Mounted condition of Head Light Guard
is shown in the drawing.

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets