SRC H-CRF300L-04-01-AL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
NO. Description Quantity Torque * (N-M) Remarks **
1
2
1
1
2
1
2
8
1
4
8
4
5.5
2
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Top Rack
Rack LH
Rack RH
Bush 18 x 31
Bush 18 x 38
Countersunk Washer M8
Plastic Knobs
OilTank 3 Liter
Nut plate
Socket head cap Screw M5 x 15
Socket countersunk head cap Screw M8 x 60
Socket countersunk head cap Screw M5 x 15
Washer M5
Use LiquidThread Locker
23
5.5 Use LiquidThread Locker
2
16
Socket countersunk head cap Screw M8 x 65 23 Use LiquidThread Locker
Use LiquidThread Locker
Flank
Cap lock
SRCDesign uses MetricSystem of Measurement and all dimensions in Millimeters
*Recommended to use the Torque specified in the table
**Denotes Usage of Liquid Thread Locker in specified Locations
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-CRF300L-04-01-AL / H-CRF300L-04-02-AL / H-CRF300L-04-03-AL
Part Description Top Rack–HONDA CRF 300 L / HONDA CRF 300 RALLY
Applicable to Finished colour versions of Black
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
Step 1:
Before starting to mount the Top
Rack we can remove the original
screw in motorbike (as show)
Step 3:
Orient and Align the Top Rack (1), as shown, Slip-in the Bush Spacer 18 x 31 mm (4) –1
off between the Mounting hole front side and Slip-in Screw M8x 60 (14) –1off and
Taper Ring M8 (11) –1off , Slip-in the Bush Spacer 18 x 38 mm (5) –1 off between the
Mounting End hole and Slip-in Screw M8 x 65(15) –1 off and Taper Ring M8 (11) –1
off, and slip-in the screw M5 x 15 (13) - 4 off , washer M5 (16) - 4 off ,through the holes
and secure the threads.
Step 2:
Repeat the Step 1 for mounting
the Top Rack, as shown
Mounting Instruction

Copyright By SRC
Design and Specification are subjected to change
Page 3
Step 4:
Repeat the above step
for the other side to
secure the threads.
Step 5:
Mounting Set Oil !

Copyright By SRC
Design and Specification are subjected to change
Page 4
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
9. If any additional modifications are to be done, prior to the fitment of the accessories, it will be
explicitly specified in the instruction sheets