SRC R-HM18-14-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
NO. Description Quantity Torque * (N-M) Remarks **
11
1
1
2
4
415
3
4
5
Bottom Plate
Middle Plate
Top Plate
SRCDesign uses Metric System of Measurement and all dimensions in Millimeters
*Recommended to use the Torque specified in the table
**Denotes Usage of Liquid Thread Locker in specified Locations
Use Liquid Thread Locker
15 Use Liquid Thread Locker
Nut M6
Screw M6 X 20
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: R-HM18-14-01-SL
Part Description: Large Side Stand –Royal Enfield Himalayan
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Step 1:
During Mounting the Large Side Stand, let the Motorbike firmly rest
on the floor, using the Centre Stand.
The Middle Plate (2) serves as the Sandwich between the Top Plate
and the Bottom plate. Orient the Middle Plate (2) as shown in the
drawing. It has a cut-out and it clears the Side stand base, but
slightly hugs the Side stand base, around its periphery.
Step 2:
Orient the Bottom plate (1) as shown in the drawing and
visually orient and align the 4 mounting holes of the bottom
plate and the Middle Plate (2).
Orient the Top plate (3), as shown in the drawing (it has the cut-
out to clear the gusset feature of the Side stand) and visually
orient the 4 mounting holes to the plate clusters below.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 3:
Slide in the 4 Screws (4), as shown in the drawing, and
ensure it is aligning all the 3 plates as a cluster and
secure the threads using the 4 Nuts (5), as shown in the
drawing.
Step 4:
The threads can be tightened to the
torque, as given in the table.
The above drawing represents the “As Is
Mounted Condition” of the Large Side
Stand. It improves the foot print of the
OE feature and improves the static
stability, when the Motorbike is parked
using the Side stand.

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-
by-step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to
the Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part
and its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part.
It is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride
and at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle
or the Part on which it is mounted to protect it
9. If any additional modifications are to be done, prior to the fitment of the accessories, it will be
explicitly specified in the instruction sheets.