SRC H-X-ADV-14-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-X-ADV-14-01-SL
Part Description: Large Side Stand –HONDA X - ADV
Installation / Parts List / Bill of Material for Mounting
No. Description Quantity Torque * (N-m) Remarks **
1 Bottom Plate 1
2 Middle Plate 1
3 Top Plate 1
4 Screw M6 x 20 4 15 Use Liquid Thread Locker
5 Nut M6 4 15 Use Liquid Thread Locker
SRC Design uses Metric System of Measurement and all dimensions are in Millimeters
* Recommended to use the Torque specified in the table
** Denotes Usage of Liquid Thread Locker in specified locations

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Mounting Instructions
Step 1:
During Mounting the Large Side Stand, let
the Motorbike firmly rest on the floor,
using the Centre Stand.
The Middle Plate (2) serves as the
Sandwich between the Top Plate and the
Bottom plate. Orient the Middle Plate (2)
as shown in the drawing. It has a cut-out
and it clears the Side stand base, but
slightly hugs the Side stand base, around
its periphery.
Step 2:
Orient the Bottom plate (1) as shown in
the drawing and visually orient and align
the 4 mounting holes of the bottom plate
and the Middle Plate (2).
Orient the Top plate (3), as shown in the
drawing (it has the cut-out to clear the
gusset feature of the Side stand) and
visually orient the 4 mounting holes to
the plate clusters below.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 4:
The threads can be tightened to
the torque, as given in the
table.
The above drawing represents
the “As Is Mounted Condition”
of the Large Side Stand. It
improves the foot print of the
OE feature and improves the
static stability, when the
Motorbike is parked using the
Side stand.
Step 3:
Slide in the 4 Screws (4), as shown in the
drawing, and ensure it is aligning all the 3
plates as a cluster and secure the threads
using the 4 Nuts (5), as shown in the drawing.

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and
follow the step-by-step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the
Accessory part to the Vehicle. We have prepared this based on our experience and
knowledge, related to the Vehicle, Part and its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s
accessory part. It is advised to the User, to inspect and ensure the original state of all other
Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour
and/or the stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will
help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all
functions of the Vehicle. It is always advised to check loosening of the fasteners after the first
50 kilo meters of ride and at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8. The SRC Fuel Tank, as shown in the Full Assembly Drawing, consists of various parts
9. The Fuel Tank uses the Mounting that is already available in the Motorbike
10. To the maximum extent possible, our design use the current Mounting/Fitment of the
Original Equipment, so that Installation of these accessories will not affect the Payload or
Function of the Vehicle or the Part on which it is mounted to protect it
11. If any additional modifications are to be done, prior to the fitment of the accessories, it
will be explicitly specified in the instruction sheets.