SRC H-AFT18-01-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
No. Description Quantity Torque * (N-m) Remarks **
1 Head Light Guard 1
2 Grommet 4
3 Pin 4
4 Lower Bracket 1
5 Upper Bracket 1
6 Spacer 2
7 Washer M6 2
8 Washer M5 4
9 Screw M6 x 20 2 15 Use Liquid Thread Locker
10 Screw M5 x 6 4 10 Use Liquid Thread Locker
11 Nut M6 2
SRC Design uses Metric System of Measurement and all dimensions are in Millimeters
* Recommended to use the Torque specified in the table
** Denotes Usage of Liquid Thread Locker in specified locations
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-AFT18-01-01-SL / H-AFT18-01-02
Part Description: Head Light Guard –HONDA CRF1000L AFRICA TWIN ADVENTURE SPORT
Applicable to Finished colour versions of Black and Silver
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
No. Description Quantity Torque * (N-m) Remarks **
1 Head Light Guard 1
2 Grommet 4
3 Pin 4
4 Lower Bracket 1
5 Upper Bracket 1
6 Spacer 2
7 Washer M6 2
8 Washer M5 4
9 Screw M6 x 20 2 15 Use Liquid Thread Locker
10 Screw M5 x 6 4 10 Use Liquid Thread Locker
11 Nut M6 2
SRC Design uses Metric System of Measurement and all dimensions are in Millimeters
* Recommended to use the Torque specified in the table
** Denotes Usage of Liquid Thread Locker in specified locations
Mounting Instructions
Part Number: H-AFT17-01-01-SL / H-AFT17-01-02
Part Description: Head Light Guard –HONDA CRF1000L AFRICA TWIN
Applicable to Finished colour versions of Black and Silver
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 1:
Unscrew the two mounting
screws of the Windshield Guard
to enable access and fitment of
the upper bracket (5)
Step 2:
Mounting the Upper Bracket (5)
and the Windshield Guard (back in
its position)
Orient and Align the Upper
Bracket and Windshield Guard, as
shown in the drawing, Slide in the
Mounting Screws of the
Windshield Guard and secure the
threads and tighten it fully.
Slide in the Mounting Pin (3) –2
off and Grommet (2) –2 off as
shown, in the upper bracket (This
can be done off-line too)

Copyright By SRC
Design and Specification are subjected to change
Page 5
Step 3:
Mounting of the Lower Bracket
(4).This takes the mounting hole
available in the Motorbike (as shown
in the drawing).
Orient and align the Lower Bracket,
and slide in the Spacer (6) –2 off,
Washer M6 (7) –2 off, Screw M6 x 20
(9) –2 off, and secure the threads
using Nut M6 (11) –2 off from the
other side.
Slide in the Mounting Pin (3) –2 off
and Grommet (2) –2 off as shown, in
the upper bracket (This can be done
off-line too)
The Upper Bracket and Windshield
Guard shown in “As is mounted
condition”

Copyright By SRC
Design and Specification are subjected to change
Page 6
Step 4:
Orient the Head Light Guard, in-line
the Projecting and Mounting Pins.
Step 5:
Secure the Annular groove in the
grommet to the inner peripheral
surface of the Head Light Guard.
Visually ensure the Orientation and
position of the Head Light Guard.

Copyright By SRC
Design and Specification are subjected to change
Page 7
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets