SRC H-X-ADV-21-04-01 User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
NO. Description Quantity Torque * (N-M) Remarks ** Chack List
4
4
4
4
4
4
1
1
1
2
3
4
5
6
7
8
Top Rack
Socket countersunk head Screw M6x20
Socket countersunk head Screw M8x30
Countersunk Washer M6
Countersunk Washer M8
Bush M6 18x10
Bush M8 18x10
Bottom Plat
9.6 Use LiquidThread Locker
23 Use LiquidThread Locker
SRCDesign uses MetricSystem of Measurement and all dimensions in Millimeters
*Recommended to use the Torque specified in the table
**Denotes Usage of Liquid Thread Locker in specified Locations
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-X-ADV-21-04-01 / H-X-ADV-21-04-02
Part Description: Top Rack –HONDA X-ADV 750 2021
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
Original Screw
Original Screw
Original Screw
Original Screw
2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Original Screw
Original Screw
Original Screw
Original Screw
2
MOUNTING INSTALLATION
STEP 1:
The Driver seat must be moved up (as shown
in the drawing
Unscrew the Mounting screws (4 off), as
shown in the drawing, and take out
STEP 2:
Orient and align the Bottom Plat (2) in-line
with the Panel mounting holes, and bring the
panels exactly in-line with them, and slip-in
the Mounting The Screw M8x30 (7) 4 off and
Bush M8 18x10 (4) 4 off, on each side and
secure the threads.

Copyright By SRC
Design and Specification are subjected to change
Page 4
STEP 3:
Slip in the Top Rack (1) and slip-in the Taper
Ring M6 (6) 4 off , and Screw M6 x 20 (5) 4 off,
and Bush M6x10 (3) 4 off through the
Mounting holes in the Top Rack and, tighten it
to the torque .
Rear Rack as shown “Final Assembled condition”

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and
follow the step-by-step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the
Accessory part to the Vehicle. We have prepared this based on our experience and
knowledge, related to the Vehicle, Part and its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s
accessory part. It is advised to the User, to inspect and ensure the original state of all
other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving
behaviour and/or the stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it
will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all
functions of the Vehicle. It is always advised to check loosening of the fasteners after
the first 50 kilo meters of ride and at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8. To the maximum extent possible, our design use the current Mounting/Fitment of the
Original Equipment, so that Installation of these accessories will not affect the Payload
or Function of the Vehicle or the Part on which it is mounted to protect it
9. If any additional modifications are to be done, prior to the fitment of the accessories, it
will be explicitly specified in the instruction sheets.