SRC BMW-310GS-01-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: BMW-310GS-01-01-SL / BMW-310GS-01-02
Part Description: Head Light Guard –BMW 310 GS
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
The Mounting hole, which will be used for mounting
the Brackets of the Head Light Guard, can be found on
the Front Left hand side and Right hand side.
(Shown in the drawing in Red color, is the view of it
from the Left Hand Side, when looking from the front
side of the Motorbike). The screws can be removed
and kept aside and, in its place, SRC’s child part (12)
M6 x 60 must be used.
Step 1:
Orient the Bracket LH (1) in-line with the
Mounting Holes of the OE Bracket and slip-in
the Taper Ring M6 (11) –1off, Screw M6 x 60
(12) –1 off, Delrin (10) –1off, & Rubber Spacer
(5) –1 off, in positions as shown and secure the
threads.
The Mounting Pin (2) –2 off can be assembled
to the Bracket. The same can be assembled Off-
line too.
Step 2:
Repeat the Step 2 for mounting the
Bracket (RH) (9), as shown
Mounting Instructions

Copyright By SRC
Design and Specification are subjected to change
Page 4
Bracket RH & Bracket LH is shown
in “As is mounted condition”
Step 3:
Orient and Align the Bottom Plate (8) in-line
with the bottom side mounting holes of the
Head Light Guard (4), as shown.
Slip-in the Screw M5x10 (7) –2off, Washer M5
(6) –2off, and the
Rubber Spacer (5) –1off, in
positions as shown and secure the threads.
The Rubber Spacer (5) 1 off is to be fitted to the
Bottom Plate (8), as shown and it must rest on
the inside surface of the head lamp, and
dampening the Head Light Guard assembly
against any kind of vibrations, during riding.

Copyright By SRC
Design and Specification are subjected to change
Page 5
Step 4:
Refer to the same drawing as
above for Mounting the Head
Light Guard.
Orient the Head Light Guard (1),
as shown. Assemble the
Grommet (4) –4 off, hugging
and flush, with the outer
surfaces of the Head Light
Guard.
The Installation of the Head Light
Guard is complete and is as shown

Copyright By SRC
Design and Specification are subjected to change
Page 6
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets