SRC H-CRF17-14-02-SL Guide

Copyright By SRC
Design and Specification are subjected to change
Page 1
NO. Description Quantity Torque * (N-M) Remarks ** Check List
4
4
4
9 - 10
1
1
1
1
1
2
3
4
5
6
7
Bottom Plate
Top Plate
Buffer Plate
Middle Plate
Spacer 15 x 15
Use LiquidThread Locker
Nut M6
SRCDesign uses MetricSystem of Measurement and all dimensions in Millimeters
*Recommended to use the Torque specified in the table
**Denotes Usage of Liquid Thread Locker in specified Locations
Countersink Screw M 6 X 35
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-CRF17-14-02-SL ( Supplement )
Part Description: Large Side Stand –HONDA CRF250 RALLY
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Mounting Instructions
Step 1:
During Mounting the Large Side Stand, let the
Motorbike firmly rest on the floor, using the
Centre Stand.
The side stand can be brought forward
(position as shown in the drawing) to have
access to the Mounting/ Assembly of the SRC
Large Side Stand.
Step 2:
Orient and slip-in the Upper Plate (2),
through the Open cut-out and pass the
shank of the Side-stand, as shown.
Step 3:
Orient and align the Middle Plate (6), as
shown, and in-line with the 4 off Mounting
hole in the Upper plate.
The Middle plate’s inner walls closely hug the
outer peripheral walls of the Side-stand base.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 4:
Slip-in the Buffer Plate (3), Spacer (4) –4 off
and Lower Plate (1), as shown and in-line with
the mounting holes.
Slip-in the Countersunk screw M6 x 35 (5) –4
off through the bottom side of the lower
plate.
Step 5:
Orient and Stack the Plates closely, as shown
and check for any slackness.
The Countersunk screws to flush into the
countersunk bores of the Lower Plate.
Slip-in the Nut M6 (7) –4 off from the top
side and secure the threads on the
Countersunk screws.

Copyright By SRC
Design and Specification are subjected to change
Page 5
Step 6:
Fully tighten the Nut M6 to torque as per specification in
the BOM table.
The final mounted condition of the Large Side Stand will be
as shown in the drawing above.

Copyright By SRC
Design and Specification are subjected to change
Page 6
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and
follow the step-by-step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the
Accessory part to the Vehicle. We have prepared this based on our experience and
knowledge, related to the Vehicle, Part and its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s
accessory part. It is advised to the User, to inspect and ensure the original state of all other
Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour
and/or the stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will
help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all
functions of the Vehicle. It is always advised to check loosening of the fasteners after the first
50 kilo meters of ride and at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8. To the maximum extent possible, our design use the current Mounting/Fitment of the
Original Equipment, so that Installation of these accessories will not affect the Payload or
Function of the Vehicle or the Part on which it is mounted to protect it
9. If any additional modifications are to be done, prior to the fitment of the accessories, it
will be explicitly specified in the instruction sheets.