STI SS2 6 Series User manual

Install or Remove Contact Block
INSTALL
To attach, align tabs (as shown) and gently snap top
then bottom. Be sure to hear BOTH tabs snap into
place. (Can be reversed if wiring comes from the
bottom of the box.)
REMOVE
Repeat STEP A from the top and bottom tab before
pulling on contact block.
Step A: Position small flat screwdriver blade under
tab and gently rotate until tab disengages. The
contact block will rotate a little. DO NOT PULL YET.
Step B: Repeat for opposite tab.
Step C: When both tabs are disengaged, pull the
contact block straight off.
Back box must be
mounted with arrows
pointing up
Drill out the (4) mounting
holes, one in each corner
using 5/32in.
drill bit
124mm
(4.9 in.)
124mm
(4.9 in.)
41.3mm
(1.63 in.)
22.23mm
(.88 in.)
A
B
STEP A COMPLETED
TOP TAB
IP67 CABLE GLAND SUGGESTED
(LTG-39897 SHOWN) DRILL BIT
SIZE 5/8 in. (16mm) - (FOR
SS2xx7 MODELS ONLY)
DRILL POINTS FOR IP CABLE GLANDS IF
REQUIRED (FOR SS2xx7 MODELS ONLY)
41.3mm
(1.63in.)
40mm
(1.5in.)
MOUNTING DIMENSIONS
SS2xx6 - suitable for flush or surface installation
SS2xx7 - suitable for surface installations ONLY
SWITCH RATING
2 momentary independent Form “C” contacts, DPDT
Rated at: 10A. 125/250VAC; 1/2 HP
6A, 30 VDC
100, operations
Temperature SS2xx6 models: 0oC to 49oC (32oF to 120oF)
Temperature SS2xx7 models: -35oC to 66oC (-31oF to 150oF)
NOTE
LED connection is polarity sensitive. If
LED does not light, switch positive and
negative wiring or remove LED and
rotate 180o. 24 volt is included and will
operate on 12 volts; however not as
bright. 12 volt LED’s are also available.
NC
NO
COM
LED
TERMINALS
INSTALLATION OF SS-2000 SERIES STOPPER®STATION
1027IS JAN2017
All specifications and information shown were current as of publication, and are subject to change without notice
INSTALLATION OF SS2xx6 & SS2xx7 SERIES STOPPER®STATION
All specifications and information shown were current as of publication, and are subject to change without notice
ID_SS2xx6_07_Rev0320
41.3mm
(1.63 in.)
22.23mm
(.88 in.)
12mm
(.47 in.)
DIMENSIONS
FLUSH SURFACE
Step B Step C
Step A
E-mail: [email protected] • Web: www.sti-usa.com
USA - Headquarters
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: [phone] • Fax: [phone]
Tel: [phone] Fax: [phone]
E-mail: [email protected] • Web: www.sti-emea.com
European Office
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England

E-mail: [email protected] • Web: www.sti-usa.com
USA - Headquarters
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: [phone] • Fax: [phone]
Tel: [phone] Fax: [phone]
E-mail: [email protected] • Web: www.sti-emea.com
European Office
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England
INSTALLATION OF SS-2000 SERIES STOPPER®STATION
1027IS JAN2017
All specifications and information shown were current as of publication, and are subject to change without notice
INSTALLATION OF SS2xx6 & SS2xx7 SERIES STOPPER®STATION
All specifications and information shown were current as of publication, and are subject to change without notice
ID_SS2xx6_07_Rev0320
Safety Notice to Installers and Users
This push button has been tested according to UL2017. It is important to read, understand and follow all instructions provided with this product. Non-fire alarm initiating devices are listed in UL category UEHX.
It is the installer’s responsibility to comply with NEC and Canadian electrical codes. To avoid electrical shock, DO NOT attempt to install this product when power is on. To avoid possible confusion with fire
alarm initiating device, do not mount a red stopper station near a manual fire alarm initiating device. ADA mounting compliance requires the operable part of the initiating device shall not be less than 1.1m (3
1/2 ft) or greater than 1.37m (4 1/2 ft) above finished floor service. After installation and testing are complete, provide a copy of this manual to all personnel responsible for testing and maintenance of this
product. Push buttons for outdoor use must be mounted with STI outdoor rated covers.
Testing Approvals
It has been tested and approved or listed by:
SS2xx6: Underwriter Laboratories and cUL No. S7255.
SS2xx7: Underwriter Laboratories and cUL No. S7255, Type NM suitable for indoor/outdoor use.
Warranty
Three year guarantee against breakage of polycarbonate in normal use (one year on electro mechanical
and electronic components). Electronic warranty form at www.sti-usa.com/wc14.
WARNING: This product can expose you to chemicals including Dichloromethane,
which is known to the State of California to cause cancer, and Bisphenol A (BPA)
which is known to the State of California to cause birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
INSTALLATION OF SS-2000 SERIES STOPPER®STATION
1027IS JAN2017
All specifications and information shown were current as of publication, and are subject to change without notice
INSTALLATION OF SS2xx6 & SS2xx7 SERIES STOPPER®STATION
All specifications and information shown were current as of publication, and are subject to change without notice
INSTALLATION OF SS-2000 SERIES STOPPER®STATION
1027IS JAN2017
All specifications and information shown were current as of publication, and are subject to change without notice
INSTALLATION OF SS2xx6 & SS2xx7 SERIES STOPPER®STATION
All specifications and information shown were current as of publication, and are subject to change without notice
#8-32 x .375 in.
SCREW
G03412 SURFACE GASKET
(ONLY SUPPLIED WITH SS2xx7 MODELS)
#6 x 1in. PHILLIPS PAN HEAD SCREW (4)
PROVIDED WITH KIT-71100A-*COLOUR*
DRILL POINT PROVIDED TOP & BOTTOM FOR
1/2 in. CONDUIT. DRILL AS NEEDED
#8-10 7/8 in. RAWL PLUGS
(4) PROVIDED WITH KIT-71100A-*COLOUR*
DRILL (4) 3/16 in. DIAMETER HOLES
#4 x 1¼ in. SELF TAPPING
SCREW (2) PROVIDED
SURFACE
MOUNTING
KIT-71100A-*COLOUR*
(order seperately)
FLUSH MOUNTING
SS2xx6 ONLY
#4 x 1¼ in. SELF TAPPING SCREW (2)
PROVIDED WHEN USING SPACER
KIT-102720-COLOUR
*NOTE: USE #6-32x1in. WHEN FLUSH
MOUNTING TO USA-TYPE OUTLET BOX
#8-32 x 3/8 in. SCREW
M3.5 x 35mm COUNTER
-SUNK MACHINE SCREW
(2) PROVIDED with
KIT-102720-*COLOUR*
KIT-102720-*COLOUR*
MOUNTING SPACER
(OPTIONAL)