Target windham accent cabinet User manual

>>
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
windham
accent cabinet
assembly instructions
style # WNCBNTKDRD (red)
dpci # 249-16-0724
tcin # 14395598
style # WNCBNTKDBK (black)
dpci # 249-16-0726
tcin # 14395596
style # WNCBNTKDBL (teal)
dpci # 249-16-0085
tcin # 15102614
style # WNCBNTKDGY (gray)
dpci # 249-16-0084
tcin # 14372259
style # WNCBNTKDWH (shell)
dpci # 249-16-0719
tcin # 14372249
style # WNCBNTKDOV (overcast)
dpci # 249-16-4305
tcin # 50076625

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-14
how to adjust door alignment 15
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

4
hardware
(H1) x 8
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
(H4) x 21
short pan head screw
(H5) x 8
short at head screw
(H6) x 4
shelf support
(H7) x 2
knob
(H8) x 2
knob bolt
(H9) x 1
long at-head screw
(H10) x 1
magnet
(H11) x 1
38mm wall screw
(H12) x 1
wall anchor
(H13) x 1
wall strap
(H14) x 1
15mm truss head screw
(H15) x 2
washer

5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side panel 1
C right side panel 1
D bottom panel 1
E shelf panel 1
F left door 1
G right door 1
H back panel 1

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
1. 2. 3.
4. 5.
6

7
step 1: attach right side panel to bottom panel
(H1) x 2
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
1.1. Carefully tap small wooden dowels into place in right side panel. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in right side panel.
1.3. Refer to page 6 for instructions on how to use the cam lock system. Do not over tighten bolts.

8
step 2: attach left side panel
(H1) x 2
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
2.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush in left side panel.
2.3. Refer to page 6 for instructions on how to use the cam lock system. Do not over tighten bolts.

step 3: attach top panel
(H1) x 4
wooden dowel
(H4) x 2
short pan
head screw
(H9) x 4
long at
head screw
(H10) x 1
magnet
3.1. Align short pan head screws with pre-drilled holes to attach magnet to top panel. Do not over tighten screws.
3.2. Carefully tap small wooden dowels into place in top panel. Leave 1/2” of the dowels sticking out.
3.3. Align long at head screws with pre-drilled holes to attach side panels to top panel. Do not over tighten screws.
9
(H4)
Align short pan head screws with pre-drilled holes to attach magnet to top panel. Do not over tighten screws.
Carefully tap small wooden dowels into place in top panel. Leave 1/2” of the dowels sticking out.

step 4: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 19
short pan head screw
4.1. Make sure the short pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
step 4.
10
Hole for anti-tip kit. pre-drilled holes