Target warwick FKWWLBCBBR User manual

warwick
library cabinet
>> assembly instructions
style # FKWWLBCBBR (fawn brown)
dpci # 249-17-0827
tcin # 53536786
style # FKWWLBCBWH (white)
dpci # 249-17-3054
tcin # 54187402
style # FKWWLBCBBK (jet black)
dpci # 249-17-6416
tcin # 78054342

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4-5
parts list 6
assembly 7-13
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 12
dowel
(H2) x 8
bolt
(H3) x 8
lock washer
(H4) x 23
pan head screw
(H5) x 4
handle bolt
(H6) x 2
handle
(H7) x 8
shelf pin
(H8) x 2
long at head screw
(H9) x 1
allen wrench
(H10) x 6
hinge

5
hardware
(H11) x 24
short at head screw
(H12) x 1
wall anchor
(H13) x 1
wall screw
(H14) x 1
truss head screw
(H15) x 1
wall strap
(H16) x 10
washer

exploded diagram
ITEM DESCRIPTION QUANTITY
1 top panel 1
2 left side panel 1
3 right side panel 1
4 bottom panel 1
5 adjustable shelf 2
6 back panel 1
7 door 2
8 stretcher 1
6

step 1: attach top panel, bottom panel, and bottom rail to side panels
(H1) x 12
dowel
(H2) x 8
bolt
(H3) x 8
lock washer
(H16) x 8
washer
(H9) x 1
allen wrench
1.1. Carefully small wooden dowels into place in top panel, bottom panel, and bottom rail. Leave 1/2” of the dowels sticking out.
1.2. Align bolts with pre-drilled holes to attach top panel to side panels. Do not over tighten bolts.
1.3. Do not over tighten bolts.
7

step 2: secure bottom rail
(H8) x 2
long at head
screw
2.1. Do not over tighten screws.
8
front

step 3: attach back panel
FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 23
pan head screw
3.1. Make sure the pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
9
front
hole for anti-tip
** **

step 4: install adjustable shelf
(H7) x 8
shelf support
4.1. Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
4.2. Angle shelf to t between the rails and set on top of shelf supports.
10
nished edge
nished edge