Target Halsted FRS80921B User manual

Halsted
Right Angle Corner
style # FRS80921B
dpci # 009000787
>>assembly instructions

Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
ATTENTION:
This Chair is not intended for use during any kind of inclement weather and the manufacturer is not,
and can not be, held responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Chair not being stored properly when not in use, is not the
responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Chair needs to be stored in a dry, sheltered place to
prolong the life and to avoid damage to the Chair.
2
IMPORTANT WARNING:
Unpack the box on a clean, soft, level surface and make sure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.

WARRANTY:
This Chair comes with a one year limited warranty against original manufacture defects. If you experience
trouble with your chair, please call the customer service number below.
3
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Yotrio 2019
before you begin
1. Check for damage or missing parts. Call to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
855-MYTGTHOME (855-698-4846)

table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-11
QUESTIONS?
4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware
5
(Part E)×2
M6*25 mm screw with washer
(Part F)×2
M6*40mm screw with washer
(Part G)×4
M6*50mm screw with washer
(Part I)×1
allen wrench
(Part H)×4
M6*25 mm screw

ITEM DESCRIPTION QUANTITY
1
1
1
A
B
C
6
back panel 1
chair seat
back panel 2
2
Dchair feet

7
step 01:
Do not completely tighten screws until all screws are started.
1. Attach the chair seat (C) to the back panel 1(A) by lining up screw holes
on the chair seat (C)with corresponding screw holes on the back panel 1 (A).
m part, tightenottobehtno)F(rehsaww withercsmm40*6MhtiweruceS.3
using allen wrench (I).
2. Secure with M6*50mm screw with washer (G) on the upper part.
tighten using allen wrench (I).
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
1. 2.
(Part E)×2
M6*25 mm screw with washer
(Part F)×2
M6*40mm screw with washer
(Part I)×1
allen wrench
(Part G)×4
M6*50mm screw with washer
(Part H)×4
M6*25 mm screw

step 02:
8
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
Do not completely tighten screws until all screws are started.
1.
1. Attach the chair seat (C) and back panel 1(A) to the back panel 2 (B) by lining up screw holes
on the chair seat (C) and back panel 1(A) with corresponding screw holes on back panel 2 (B).
mottobehtno)F(rehsaww withercsmm40*6Mh M6*25mm screw with washer (E) andtiweruceS.3
part. tighten using allen wrench (I).
2. Secure with M6*50mm screw with washer (G) on the upper part. tighten using allen wrench (I).
2. 3.
(Part E)×2
M6*25 mm screw with washer
(Part F)×2
M6*40mm screw with washer
(Part I)×1
allen wrench
(Part G)×4
M6*50mm screw with washer
(Part H)×4
M6*25 mm screw

step 03:
9
Do not completely tighten screws until all screws are started.
1. Attach the back panel 1 (A) to the back panel 2 (B) by lining up screw holes
on the back panel 1 (A) with corresponding screw holes on the back panel 2(B) .
2. Secure with M6*25 mm screw with washer (E),tighten using allen wrench (I).
(Part E)×2
M6*25 mm screw with washer
(Part F)×2
M6*40mm screw with washer
(Part I)×1
allen wrench
(Part G)×4
M6*50mm screw with washer
(Part H)×4
M6*25 mm screw

step 04:
10
Do not completely tighten screws until all screws are started.
1. Attach the chair feet (D) to the chair seat (C) by lining up screw holes
on the chair feet (D) with corresponding screw holes on the chair seat (C).
2. Secure with M6*25mm screw (H), tighten using allen wrench (I).
(Part E)×2
M6*25 mm screw with washer
(Part F)×2
M6*40mm screw with washer
(Part I)×1
allen wrench
(Part G)×4
M6*50mm screw with washer
(Part H)×4
M6*25 mm screw