TCS ISH3030 User manual

TCS TürControlSysteme AG, TCS Hotline Germany: +49 (0) 41 94/ 9 88 11 88 Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2 A
Product information
Door telephone
ISH3030

2 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Table of contents
Scope of delivery .................................................................................................................3
Safety instructions................................................................................................................3
Intended use........................................................................................................................3
max. number ISH3030 in 2-wire operation.......................................................................3
max. number ISH3030 in 3-wire operation.......................................................................4
Indication and operating elements.......................................................................................4
Device overview...................................................................................................................5
Technical data .....................................................................................................................5
Short description..................................................................................................................6
Installation............................................................................................................................6
Install the lower cover.......................................................................................................6
Connecting the lines (2-wire technique)...........................................................................7
See wiring example on page 9.........................................................................................7
Snapping-on the upper cover...........................................................................................7
Connect the handset........................................................................................................7
Open the device...............................................................................................................8
Installation of extended functions.....................................................................................8
Connecting the lines ............................................................................................................9
Connecting lines...............................................................................................................9
Wiring diagram.................................................................................................................9
Connection diagram 2-wire technique............................................................................10
Connection diagram 3-wire technique............................................................................10
Replacing an ISH1030 or TTS1 by an ISH3030.............................................................10
Commissioning ..................................................................................................................10
Settings..............................................................................................................................10
Pre-adjusted times .........................................................................................................10
2-wire/3-wire operation...................................................................................................11
Ring tone selection.........................................................................................................11
Adjust the volume...........................................................................................................12
Configuration options.........................................................................................................12
Programming with the Service Device TCSK-01............................................................12
General to the conduit in TCS audio systems....................................................................13
Principle loop resistance.............................................................................................13
Resistance measurement...........................................................................................13
Repair................................................................................................................................14
Error detection and indication.........................................................................................14
Substitution of an indoor station –programming bell buttons.........................................14
Cleaning.............................................................................................................................15
Conformity .........................................................................................................................16
Information on disposal......................................................................................................16
Warranty............................................................................................................................16
Service...............................................................................................................................16

07/2013 3
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Scope of delivery
1 x indoor station ISH3030: upper cover, lower cover, handset with connecting line
product information
instruction manual
Safety instructions
!
Notice! Mounting, installation, commissioning and repair of electrical devices have to
be carried out only by qualified electricians! Thus the standards and rules for the in-
stallation of systems must be observed!
When installing TCS:BUS systems the general safety regulations for telecommunication
systems after VDE 0800 have to be observed:
separated conduit of heavy current and low current lines,
minimum distance of 10 cm in case of a common conduit,
use of separators between heavy and low current lines in shared cable ducts,
use of standard communication lines, e.g. J-Y (St) Y with a diameter of 0.8 mm,
existing lines (modernisation) with deviating diameters can be used in compliance of the
loop resistance.
!
With suitable requirements to protect against lightning it is imperative that the electric
tension of each 32 V DC is not exceeded at the connections a,b,P,E.
Intended use
The ISH3030 are door telephones for the object area.
They are suitable for the operation in TCS audio systems and combined audio / video
systems.
They are suitable for surface-mount.
max. number ISH3030 in 2-wire operation
In case of using power
supply and control unit
max. number
ISH3030
BVS20 or
NBV1000, 1 line
20
BVS100,
distributed on 3 lines
80
PSG02, 1 line
30

4 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
max. number ISH3030 in 3-wire operation
in case of using power
supply and control unit
max. number
ISH3030
BVS20 or
NBV1000, 1 line
20
BVS100,
distributed on 3 lines
80
PSG02, 1 Strang
90
BVS20 + NGV1011,
1 line
90
AS front-door station
VS power supply and control unit
IS indoor station
Note: The number of the max. connectable AS is lim-
ited and is described in their product information!
BVS100 + NGV1011,
3 lines
270
Indication and operating elements
handset
communicating to the door
end communication
call OFF button
press short: ring tone stopper
press for 8 s: initiate ring tone selection
indication call OFF
(red)
ON: call OFF activated
error indication total error: both LEDs flashing
ring tone selection: both LEDs are ON
○
control key
control function 8
ring tone selection internal call
call display (green)
ON: call, communication activated
Blinking 3 x: busy speech channal
error indication: both LEDs flashing
ring tone selection: both LEDs are ON
light switch button
switching lights
ring tone selection floor call (from the flat door)
door release button
open the door
trigger light switch function*
ring tone selection door call from front-door station

volume control for
voice output
ring tone
adjustable in 8 steps:
in case of an existing communication
in case of off-hook handset (no communication)
* if the light switch function in the front-door station is activated

07/2013 5
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Device overview
Technical data
Supply voltage: +24 V ±8 % (power supply and control unit)
Housing: plastic (colors like shown in the price list)
Dimension (in mm): H 180 x W 100 x D 50
Weight 340 g
Acceptable ambient temperature: -5 ...+ 40 °C
Degree of protection: IP30
Input current, standby 2-wire operation: I(a) = 1 mA
3-wire operation: I(a) = 0.2 mA, I(P) =0.8 mA
Max. input current: I(Pmax) = 70 mA
handset
call display (green)
indication call OFF (red)
call OFF button
light switch button
control key
ring tone loudspeaker
door release button
volume control
handset connecting line

6 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Short description
large, deteched, blue door release button
light switch button
control button with control function 8
call OFF button for ring tone mute with optical display
optical indication of door calls via LED (green)
optical indication of a busy line when voice communication is established via LED
(green)
ring tone can be adjusted by the resident, selection out of 13 in improved quality
voice volume and ring tone volume manually adjustable
acoustic call distinction between 2 front-door stations (via configurations software con-
figo™), flat door (floor door) and internal call
one parallel call can be activated (via Service Device TCSK-01 or configo™)
audio privacy function and automatic call cut-off (after 2 min)
magnetic handset cradle
pluggable handset cord
lower cover with plugged screw terminal can be pre-installed and used alternative for
sister product for hands-free talking
optical and acoustic error indication
can be functional extended by mounting places for call relays, controlling the radio sig-
nal device and EnOcean radio interface
energy efficient by a lower stand-by consumption of only 0.025 W
Installation
Install the lower cover
For placing the connection cables without
any problems, a flush-mounted socket must
be installed behind the device.
Position the flush-mounted socket below the
cable conduit.
Install the lower cover with three screws.
TIPP: Avoid tearing of the straps:
For fixing the straps do not use counter-head screws or
flat washers!

07/2013 7
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Connecting the lines (2-wire technique)
Minimize the length of the lines above the
lower cover to place the lines without any
problems and without clamping the lines
when snapping-on the upper cover.
Connect the lines according to the labeling
at: a b E P (from the bottom to the top), floor
push-button at a –E.
See wiring example on page 9.
Snapping-on the upper cover
Set on the upper cover at both adjustment
increments of the lower cover (1).
Snap-in the upper cover below with slight
pressure (2)
Connect the handset
Put the western plug of the handset cord into
the socket at the underside of the telephone.
1
2

8 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Open the device
Remove the handset cord.
There is a rectangular release opening at
the underside of the device. Insert a small
screwdriver straight and with slight pressure
into this opening.
The upper cover can be removed at the
underside (1).
Lift the upper cover out of the two upper
adjustment increments (2).
Installation of extended functions
TRE1
radio transmitter board
FFS3100
radio interface FBI4200
The extended functions (and the antenna) have to be fixed with adhesive pads in the
indoor station (see also product information of the corresponding extended function).
1
2

07/2013 9
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Connecting the lines
Connecting lines
permitted cross-section (diameter)
0.08 … 0.82 mm2(Ø 0.32 … 1.0 mm)
max. number of wires per terminal contact
each 2 x 0.8 mm, 3 x 0.6 mm
!
Further wires have to be connected via auxiliar terminals!
!
Use only connecting lines with the same diameter in one terminal contact.
Wiring diagram

10 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Connection diagram 2-wire technique
Connection diagram 3-wire technique
Replacing an ISH1030 or TTS1 by an ISH3030
The floor push-button have to be connected always to the a-wire.
In case of a parallel circuit both telephones have to be replaced by the ISH3030.
Commissioning
Install the devices of the system voltage-free and completely.
Proof the a-, b- and P-wire against each other on short-circuit.
Switch on the main voltage.
Note:
If the floor push-button is not working, proof, i fit is connected to the a-wire of the power
supply and control unit.
Settings
Pre-adjusted times
communication time
max. 2 min
flashing period of the green LED, if the voice
channal is busy after lifting the handset
2 sec
3 x flashing
internal standby time, if the device is calling or
is called
around
30 sec

07/2013 11
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
2-wire/3-wire operation
The jumper J1 is adjusted for 2-wire operation
in delivery condition. J1
2-wire operation (scope of delivery)
Put the jumper J1 on the two upper con-
tacts for the 3-wire operation.
3-wire operation
Ring tone selection
For 4 different incoming calls (door calls of 2 different front-door stations, floor call, internal
call) different ring tones can be selected.
1
End communication. Press call OFF button for ca. 8 s.
Both LEDs are on and an acknowledgement tone sounds, the ring tone selection is
activated.
By pressing the following buttons a ring tone can be selected. You can chose be-
tween 13 tones.
2a
select door ring tone
from the front-door
station*
Press the door release button as often as the required ring
tone sounds. The ring tone selected last, will be stored.
2b
select door ring tone
of floor door
Press the light switch button as often as the required ring
tone sounds. The ring tone selected last, will be stored.
2c
select internal ring to-
ne
Press the control key as often as the required ring tone
sounds. The ring tone selected last, will be stored.
3
Press call OFF button short.
In case that no button is pressed for ca. 8 s, the device ends the ring tone selection
automatically. Both LEDs go out and an acknowledgement tone sounds, the ring
tone selection is deactivated.
* The ring tone is identical for all front-door stations and can be selected only identically for all.
For selecting a second door ring tone it is necessary to activate the call distinction by changing the audio AS limit.
Changing the audio AS limit is only possible with the configuration software configo™.

12 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Adjust the volume
Each adjustable in 8 steps
volume voice
Turn the volume control of the ring tone when a voice communi-
cation is established
(adjustment ex works: volume step 6 from 8)
volume ring tone
Turn the volume control for ring tone when the handset is hooked
on (no voice communication)
(adjustment ex works: volume step 7 from 8)
A signal tone is reflecting the adjusted volume when turning the volume control of the
ring tone.
If the setting is finished, the adjusted ring tone will be reflected in the adjusted volume.
Configuration options
function
manual
TCSK-01
configoTM
from version 1.3.3
ring tone volume
x
–
x
voice volume
x
–
x
selecting ring tones for door
calls, internal calls and floor calls
x
–
x
ring tone for door call 2
–
–
x
parallel allocation
–
x
x
change audio AS limit
–
–
x
block ring tone output
x
–
–
block ring tone selection
x
reset to factory settings
–
–
x
Programming with the Service Device TCSK-01
The indoor station is acting like a telephone.
Use the commands „8“ for configuration (see product information Service Device TCSK-
01).
search telephones
activate parallel call
deactivate parallel call
Ser. No. =the serial number of the new indoor station, that should be configured
ParSNo.=the serial number of the indoor station, to which the new configured indoor station is allocated

07/2013 13
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
General information on the conduit in TCS audio systems
The conduit is determined by structural conditions and is only limited by ist length.
Note when selecting the cables: the loop re-
sistance can amount max. 20 Ω(table)
In compliance to the max. permitted loop re-
sistance the wire cross-section can be doubled,
that means, that for one wire two lines can be
used. The lines have to be twisted.
In case of using shielded cables: connect the
shielding with each other and put it one-sided on
mass (b-wire) in the power supply
Optional strand or star formed wiring
table: loop resistances
cable length in m
line diameter
0.6 mm
0.8 mm
loop resistance in Ω
10
1.28
0.71
20
2.55
1.43
30
3.83
2.14
40
5.10
2.86
50
6.38
3.57
60
7.65
4.29
70
8.93
5.00
80
10.20
5.71
90
11.48
6.43
100
12.76
7.14
150
19.13
10.71
200
25.51
14.29
250
31.89
17.86
300
38.27
21.43
Principle loop resistance
Resistance measurement
None of these devices (AS, IS or FE) should be
located more than 20 Ohm away from the power
supply and control unit (VS).
Switch off 230 V / 50 Hz of the VS.
Install a-b short-circuit at VS.
Other devices don’t disturb the measurement,
they can be connected.
Measure the resistance at a/b of the last IS or AS.

14 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
20 Ohm:
max. 160 m distance AS/IS-VS at 0.6 mm diameter
max. 300 m distance AS/IS-VS at 0.8 mm diameter
AS front-door station
VS power supply and control unit
IS indoor station
FE extended function
Repair
Error detection and indication
Errors will be indicated optical and acoustic: error tone for one time and constant flashing
of the operation indication. When pressing any button, the error tone sounds again. The
optical error indication stays active as long as the error is resolved.
error causes
display
error
mode
error tone
elimination
a- and P-wire interchanged
or short-circuited
both
LEDs
are
flashing
change a- and P-wire or eliminate short-circuit,
device is going into sleep mode again
a-wire: not connected or
not supplied
Connect the a-wire or proof power supply,
device is going into sleep mode again
button stucks
(pressed longer than 15 s)
Remove button at the device or floor push button,
device is going into sleep mode again
Substitution of an indoor station –programming bell buttons
Basic principle
All devices at the TCS:BUS got an unique serial number.
Programming a bell button means that the serial number of an indoor station is allocat-
ed to the bell button of a front-door station and is stored within the EEPROM of the
front-door station.
Ensure that the new indoor station is connected to the TCS:BUS and the mains voltage
is switched on (the operation LED at the power supply and control unit is ON) and fur-
ther, that the access to the flat is guaranteed during the programming.
This instruction describes the case, when a serial number is allocated to a bell button
and no programming lock is set. To unlock a programming lock you need a Service De-
vice TCSK-01or the configuration software configo™.
a, b hier
kurzschließen

07/2013 15
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
1
initiate
Press shortly LED blinks
Programming mode of the system is ON
2
Delete a button
◄6s►
Press until a delete tone sounds after 6 sec 1)
3
Programming via voice coummunication
oder
establish voice communication
to the front-door station 2)
press button shortly..
... until a ring tone sounds at the front-
door and indoor station 1)
4
End programming
Press shortly LED is ON
Programming mode of the system is OFF *)
1) If there sounds a Progsperr tone instead, the front-door station got a promgramming lock.
The programming lock can be unlocked only with the Service Device TCSK-01 or the configuration software configo™
2) New developed front-door stations (from 2009 on) respond to that with a positive acknowledgement, if the serial num-
ber of the indoor station was received (see product information of the front-door station).
*) device-specific indication modes of the front-door stations see product information of the front-door station
Cleaning
!
Avoid water from entering the device!
Do not use any abrasive detergents!
Clean the device with a dry or slightly wet cloth.
Remove stronger stains with a standard plastic cleaner.

16 07/2013
TCS TürControlSysteme AG Subject to technical changes.
Mail: [e-mail] ISH3030-0140 UK 2A
Conformity
Download declarations of conformity for the device from www.tcsag.de, downloads,
trade information.
Information on disposal
The adjoining symbol shows, that the device has to be disposed separately from
domestic waste. The materials used are recyclable. Please do help protecting our
environment and dispose the device via a collection point for electronic scrap.
Dispose the parts of the packaging in collecting tanks for cardboard and paper
resp. plastics.
Warranty
We offer a simplified processing in case of warranty for electrician.
Note our conditions of sale and delivery, download from www.tcsag.de, downloads,
trade information and included in our actually price list.
Please contact us: [email protected].
Service
Please send your questions and inquiries to
[email protected]
headquarters
TCS TürControlSysteme AG, Geschwister-Scholl-Str. 7, 39307 Genthin | Germany
Tel.: [phone], FAX: [phone], www.tcsag.de