Technogym RUN PERSONAL User manual

RUN
PERSONAL
REV.3.1

The information contained in this manual is intended for QUALIFIED TECHNICIANS who have
completed a specific TECHNOGYM training course and are authorized to perform machine start-up
and adjustment procedures as well as extraordinary maintenance or repairs which require a thorough
knowledge of the machine, its operation, its safety devices and working procedures.
CAREFULLY READ THE INFORMATION CONTAINED IN
THIS MANUAL BEFORE PERFORMING ANY MAINTENANCE
PROCEDURES ON THE MACHINE
DANGEROUS VOLTAGES
PRESENT
NOTE:
The information contained in this document is subject to change without notice.
Technogym does not guarantee this documentation in any way. Technogym shall not be held
responsible for any errors contained in this manual and declines all liability for accidents or
damages resulting from the supply, characteristics or use of this manual.
This document contains proprietary information that is protected by copyright. All rights reserved.
No part of this document may be photocopied, reproduced or translated into another language
without the prior written consent of Technogym.
The Technogym™ trademark is property of Technogym S.p.A.
The Run Personal™ trademark is property of Technogym S.p.A.

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page i
Contents
1. GENERAL NOTICES ............................................................................................................................................. 1.1
1.1. INTRODUCTION................................................................................................................................................... 1.1
1.2. RECOMMENDATIONS .......................................................................................................................................... 1.1
1.3. GENERAL RULES FOR REPAIR PROCEDURES ........................................................................................................ 1.2
2. TECHNICAL CHARACTERISTICS .................................................................................................................... 2.1
2.1. PRODUCT CODES ................................................................................................................................................ 2.1
2.2. SERIAL NUMBER STRUCTURE ............................................................................................................................. 2.2
2.3. TECHNICAL SPECIFICATION................................................................................................................................. 2.3
2.4. MECHANICAL CHARACTERISTICS ........................................................................................................................ 2.4
2.5. DIMENSIONS................................................................................................................................................... 2.4
2.6. PACKING DIMENSIONS EUROPE AND OVERSEAS.............................................................................................. 2.5
2.7. AMBIENT SPECIFICATIONS.................................................................................................................................. 2.6
2.8. CONFORMITY TO REGULATIONS .......................................................................................................................... 2.6
2.9. WIRING DIAGRAMS ............................................................................................................................................. 2.7
2.9.1. VISIOWEB and ALE MET-CE (220Vac)................................................................................................ 2.7
2.9.2. VISIOWEB and ALE MET-UT (110Vac)................................................................................................ 2.8
2.10.CABLES .............................................................................................................................................................. 2.9
2.10.1. CBQ Cables............................................................................................................................................ 2.9
2.10.2. WB Cables.............................................................................................................................................. 2.9
2.10.3. AUTOTRANSFORMER cable ................................................................................................................ 2.9
2.10.4. CU Cables ............................................................................................................................................ 2.10
2.10.5. TRM Cables.......................................................................................................................................... 2.17
2.10.6. Other cables ......................................................................................................................................... 2.17
3. PRINCIPLES OF OPERATION ............................................................................................................................ 3.1
3.1. BLOCK DIAGRAM:HIGH KIT AND LOW KIT......................................................................................................... 3.1
3.2. VISIOWEB DISPLAY OPERATION (HIGH KIT)..................................................................................................... 3.2
3.2.1. CPU board ............................................................................................................................................. 3.2
3.2.1.1. BackUp battery....................................................................................................................................................................... 3.2
3.2.2. LCD inverter .......................................................................................................................................... 3.3
3.2.3. Digital/Analog tuner board.................................................................................................................... 3.3
3.2.4. LAN network board (integrated) ............................................................................................................ 3.3
3.2.5. Wireless network board (without cables) ............................................................................................... 3.4
3.2.6. Audio/Video external device connector board ....................................................................................... 3.5
3.2.7. Jack cuffie............................................................................................................................................... 3.5
3.2.8. Scheda C-Safe (integrata) ...................................................................................................................... 3.5
3.2.9. Porta USB di servizio (integrata)........................................................................................................... 3.5
3.2.10. Capacitive Touch Screen control board................................................................................................. 3.5
3.3. HAND SENSOR AND CARDIO RECEIVER ............................................................................................................... 3.6
3.4. JOYSTICK............................................................................................................................................................ 3.6
3.5. EMERGENCY STOP.............................................................................................................................................. 3.6
3.6. BELT MOTOR ...................................................................................................................................................... 3.7
3.7. ELEVATION MOTOR ............................................................................................................................................ 3.7
3.8. LIMIT SWITCH ..................................................................................................................................................... 3.7
3.9. IPOD DOCKING STATION ...................................................................................................................................... 3.8
3.10.CLIENT USB PORT .............................................................................................................................................. 3.8
3.11.DUAL TGS READER............................................................................................................................................ 3.8
3.12.ALE MET DRIVER OPERATION (LOW KIT) ......................................................................................................... 3.9
3.12.1. ALE MET driver ..................................................................................................................................... 3.9
3.12.2. ALE power supply box.......................................................................................................................... 3.10
3.12.3. Supplementary power supply................................................................................................................ 3.10
3.13.AUTOTRANSFORMER ........................................................................................................................................ 3.10

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page ii
3.14.TREAD BELT MOTOR DRIVE.............................................................................................................................. 3.11
3.14.1. Mechanics ............................................................................................................................................ 3.11
3.14.2. Controls................................................................................................................................................ 3.11
3.14.3. The signals involved ............................................................................................................................. 3.12
3.15.ELEVATION MOTOR DRIVE ................................................................................................................................ 3.13
3.15.1. Mechanics ............................................................................................................................................ 3.13
3.15.2. Control ................................................................................................................................................. 3.13
3.15.3. Reset procedure.................................................................................................................................... 3.14
3.15.4. The signals involved ............................................................................................................................. 3.15
3.16.EMERGENCY STOP SIGNAL MANAGEMENT ........................................................................................................ 3.16
3.16.1. Control logic ........................................................................................................................................ 3.16
3.16.2. The signals involved ............................................................................................................................. 3.17
4. ACCESSORIES........................................................................................................................................................ 4.1
4.1. CARDIO THEATER CONNECTION .......................................................................................................................... 4.1
4.2. MONITOR PLUG FOR C-SAFE PORT ...................................................................................................................... 4.2
4.3. UPGRADE VISIOWEB....................................................................................................................................... 4.2
4.3.1. VISIO vs VISIOWEB .............................................................................................................................. 4.2
4.3.2. VISIOWEB upgrade kit .......................................................................................................................... 4.2
5. INSTALLATION INSTRUCTIONS ...................................................................................................................... 5.1
5.1. SPECIFICATIONS AND REQUIREMENTS................................................................................................................. 5.1
5.2. MOVING ............................................................................................................................................................. 5.2
5.3. INSTALLATION .................................................................................................................................................... 5.2
5.4. FIRST POWER-ON ................................................................................................................................................ 5.3
5.5. CHECK THE CORRECT OPERATION OF THE MACHINE............................................................................................ 5.3
5.6. RECOMMENDED AERIAL ANTENNA REQUIREMENTS ............................................................................................ 5.4
6. TROUBLESHOOTING........................................................................................................................................... 6.1
6.1. TROUBLESHOOTING MENU.................................................................................................................................. 6.2
6.2. THE DISPLAY STAYS OFF ..................................................................................................................................... 6.3
6.3. NO AUDIO SOUND ............................................................................................................................................... 6.7
6.4. NO TV PICTURE.................................................................................................................................................. 6.7
6.5. THE TOUCH SCREEN DOES NOT WORK /IT’S NOT CALIBRATED ............................................................................ 6.7
6.6. THE RADIO DOES NOT PLAY ................................................................................................................................ 6.7
6.7. THE IPOD DOES NOT WORK ................................................................................................................................. 6.8
6.8. THE DISPLAY SHOWS “PRESS AKEYS /TOUCH THE SCREEN”................................................................. 6.10
6.9. “THE EQUIPMENT IS LOCKED (COM)” MESSAGE ON DISPLAY ................................................................. 6.11
6.10.DRIVER ERRORS ............................................................................................................................................... 6.12
6.11.TREAD BELT MOTOR IS JERKING........................................................................................................................ 6.14
6.12.“GRADIENT NOT WORKING” MESSAGE ON THE DISPLAY .......................................................................... 6.15
6.13.THE MACHINE DOES NOT READ THE TGS KEY .................................................................................................. 6.18
6.14.THERE IS NO HEART RATE SIGNAL..................................................................................................................... 6.20
6.14.1. Hand sensor ......................................................................................................................................... 6.20
6.14.2. Chest belt.............................................................................................................................................. 6.24
6.15.THE TELEMETRIC HEART RATE SIGNAL IS INCORRECT ....................................................................................... 6.27
6.15.1. Chest belt.............................................................................................................................................. 6.27
6.15.2. Hand Sensor......................................................................................................................................... 6.31
7. PART DISASSEMBLY ........................................................................................................................................... 7.1
7.1. DISASSEMBLING THE TOUCH SCREEN.................................................................................................................. 7.1
7.2. DISASSEMBLING THE LCD.................................................................................................................................. 7.3
7.3. UPPER GUARD DISASSEMBLY:TGS, USB AND IPOD........................................................................................... 7.5
7.4. DISASSEMBLING THE DISPLAY ............................................................................................................................ 7.8
7.5. DISASSEMBLING THE DISPLAY BOARDS AND COMPONENTS............................................................................... 7.11
7.6. DISASSEMBLING THE EMERGENCY STOP ........................................................................................................... 7.16
7.7. DISASSEMBLING THE HS/HR RECEIVER............................................................................................................ 7.17
7.8. DISASSEMBLING THE HAND SENSOR ................................................................................................................ 7.18

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page iii
7.9. DISASSEMBLING THE CENTER HANDLEBAR AND JOYSTICK................................................................................ 7.19
7.10.DISASSEMBLING THE MOTOR GUARD AND SIDE UPRIGHTS................................................................................. 7.20
7.10.1. Disassembling the low kit guard .......................................................................................................... 7.20
7.10.2. Disassembling the side uprights:.......................................................................................................... 7.22
7.10.3. Disassembling the closing lower guards.............................................................................................. 7.25
7.11.DISASSEMBLING THE LOWER COMPONENTS ...................................................................................................... 7.26
7.11.1. Disassembling the ALE Drive .............................................................................................................. 7.27
7.11.2. Disassembling the elevation microswitch and the Audio/Video connectors board (B)........................ 7.28
7.11.3. Disassembling the power supply box (C) ............................................................................................. 7.31
7.11.4. Disassembling the elevation motor (D)................................................................................................ 7.32
7.11.5. Disassembling the Tread belt motor (E)............................................................................................... 7.34
7.11.6. Disassembling the belt tensioner (F).................................................................................................... 7.35
7.12.DISASSEMBLING THE TREAD BELT,RUNNING DECK AND MOTOR DRIVE-BELT ................................................... 7.36
7.13.DISASSEMBLING THE FRONT WHEELS................................................................................................................ 7.43
7.14.DISASSEMBLING THE AUTOTRANSFORMER (VER.110V) .................................................................................. 7.45
7.14.1. Position A ............................................................................................................................................. 7.46
7.14.2. Position B ............................................................................................................................................. 7.47
8. ADJUSTMENTS...................................................................................................................................................... 8.1
8.1. TENSIONING A NEW TREAD BELT ........................................................................................................................ 8.1
8.2. TENSIONING A USED TREAD BELT ....................................................................................................................... 8.2
8.3. CENTERING AND ADJUSTING THE BELT ............................................................................................................... 8.3
8.4. ALIGNING THE TREAD –BELT MOTOR DRIVE-BELT.............................................................................................. 8.4
8.5. TRAVEL LIMIT MICROSWITCH POSITION .............................................................................................................. 8.5
8.6. THE MACHINE IS NOT FLAT ................................................................................................................................. 8.6
9. EQUIPMENT CONFIGURATION........................................................................................................................ 9.1
9.1. USER MENU CONFIGURATION.............................................................................................................................. 9.1
9.2. SERVICE MENU CONFIGURATION......................................................................................................................... 9.2
9.2.1. Table of configuration parameters......................................................................................................... 9.3
9.2.2. Register Addr.......................................................................................................................................... 9.4
9.2.2.1. Read from low kit................................................................................................................................................................... 9.4
9.2.2.2. Register Value ........................................................................................................................................................................ 9.4
9.2.2.3. Write to low kit....................................................................................................................................................................... 9.4
9.2.3. Inverter parameters................................................................................................................................ 9.5
10. UPDATING THE SW............................................................................................................................................ 10.1
11. SCHEDULED MAINTENANCE ......................................................................................................................... 11.1
11.1.ORDINARY MAINTENANCE OPERATIONS ........................................................................................................... 11.2
11.1.1. Working conditions set up (Daily)........................................................................................................ 11.2
11.1.2. External cleaning operations (Daily)................................................................................................... 11.2
11.1.3. Internal cleaning operations (Monthly) ............................................................................................... 11.2
11.1.4. Checking the “Emergency stop” (Monthly) ......................................................................................... 11.2
11.1.5. Complete operation (six-menthly) ........................................................................................................ 11.2
11.2.EXTRA-ORDINARY MAINTENANCE OPERATIONS ............................................................................................. 11.3
11.2.1. Checking the operation of the cardiotester receiver ............................................................................ 11.3
11.2.2. Checking the operation of the hand sensor receiver ............................................................................ 11.3
11.2.3. Checking the working conditions ......................................................................................................... 11.3
11.2.4. Checking the wiring and connections .................................................................................................. 11.3
11.2.5. Checking the state of wear of tread belt and running deck.................................................................. 11.3
11.2.6. Checking the wear of the motor roller ................................................................................................. 11.3
11.2.7. Checking the state of wear of the driving roller................................................................................... 11.4
11.2.8. Checking the shock absorbers.............................................................................................................. 11.4
11.2.9. Checking the tread belt motor drive-belt.............................................................................................. 11.4
11.2.10. Checking and centering the tread belt ................................................................................................. 11.4
12. APPENDIX............................................................................................................................................................. 12.1
12.1.MENU PASSWORD TABLE .................................................................................................................................. 12.1

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page iv
12.2.REQUIRED TOOLS.............................................................................................................................................. 12.2

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 1.1
1. GENERAL NOTICES
1.1. INTRODUCTION
This document is reserved for Technogym Service technicians, and is intended to provide
authorized personnel with the necessary information to correctly carry out repairs and maintenance.
A thorough knowledge of the technical information contained in this manual is essential for
completing the professional training of the operator.
In order to facilitate consultation, the paragraphs are accompanied by schematic drawings which
illustrate the procedure being described.
This manual contains notices and symbols which have a specific meanings:
WARNING: non observance may result in accident or injury.
ATTENTION: non observance may cause damage to the machine.
Information about the operation in progress.
Observation about the operation in progress.
1.2. RECOMMENDATIONS
Technogym recommends the following steps for planning repair procedures:
•Carefully evaluate the customer’s description of the machine malfunction and ask all the
necessary questions to clarify the symptoms of the problem.
•Clearly diagnose the causes of the problem. This manual provides the fundamental theoretical
basis, which must then be integrated by personal experience and attendance at the training
courses periodically offered by Technogym.
•Rationally plan the repair procedure so as to minimize the downtime necessary for procuring
spare parts, preparing tools, etc.
•Access the component to be repaired, avoiding any unnecessary operations. In this regard it will
be useful to refer to the disassembling sequence described in this manual.

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 1.2
1.3. GENERAL RULES FOR REPAIR PROCEDURES
1. Always mark any parts or positions which may be confused with each other at the time of
reassembly.
2. Use original Technogym spare parts and lubricants of the recommended brands.
3. Use special tools where specified.
4. Consult the Technical Newsletters, which may contain more up-to-date information on adjusts
and maintenance than those contained in this manual.
5. Before starting the repair procedure, make sure that the recommended tools are available and in
good condition.
6. For the procedures described in this manual, use only the specified tools.
The tool sizes quoted in this manual are expressed in mm.

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.1
2. TECHNICAL CHARACTERISTICS
2.1. PRODUCT CODES
The machine codes take into account all the possible variants and options available for the products.
The machine code, which does not include the Serial Number, consists of 16 alphanumeric characters arranged
as follows:
Characters
Description
key to values
1, 2, 3,
Machine type
D94 = Run Personal
4,
Model
7 = 700
5, Power supply type
E= 200-240V - CE
1= 100-120V – MET CE
2= 200-240V – MET CE
6, Display type
C= VISIO
W= VISIOWEB
7,
Accessories
F= Full
8, 9,
Colour of the frame
00 = None
10, 11,
Colour of the upholstery
00 = None
12,
Colour of the guards
R= Renault Grey
13, TV standard receiver
D= DVB-T
A= ATSC
I= ISDB-T
14, 15,
Language
00 = Visio
16. Type of packaging
I= Italy
E= Europe
S= Overseas International
U= Overseas US / JP
Continued on following page…

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.2
For example, a possible product code would be:
D9471WF0000RD00E
which is interpreted as follows:
D94 71 W F 00 00 R D 00 E
Machine Type: RUN PERSONAL
model: 700
Driver: ALE MET-CE (110V)
Display: VISIO WEB
Accessories: FULL
Frame colour: NONE
Upholstery colour: NONE
Guard colour: RENAULT GREY
TV Standard receiver: DVB-T
Language: Multi-Language
Pakaging: EUROPE
2.2. SERIAL NUMBER STRUCTURE
The Serial Number, consists of 14 alphanumeric characters arranged as follows:
Characters
Description
key to values
1,2,3,4,5,6, Product type,
D947 = Run Personal
E=ALE Driver
1=ALE MET-CE (110V) Driver
2=ALE MET-CE (220V) Driver
C= VISIO
W= VISIO WEB
7,8,
Year of production,
10 = 2010
9,10,11,12,13,14.
Progressive.
000001
For example, a possible product code would be:
D9471C10000001

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.3
2.3. TECHNICAL SPECIFICATION
TECNICAL SPECIFICATIONS
Equipment power
requirement:
E= CE
(200-240V)
50-60Hz
(It is advisable 16A dedicated socket each machine)
1= MET CE
(100-120V)
50-60Hz
(It is advisable 20A dedicated socket each machine)
2= MET CE
(200-240V)
50-60Hz
(It is advisable 16A dedicated socket each machine)
Power Engine:
2,45 HP (AC) – 1800 Watt
Energy consumption:
1500W
VISIO Stand-by
consumption:
141,2 VA
Speed
(Km/h – mph):
0,4 Km/h - 18 Km/h ± 5%
(up to 2Km/h ± 0,1Km/h)
Max incline:
0 - 15 % ± 1%
HR monitoring:
Hand sensor, Telemetry
Calorie Coach:
YES
Runner Detection
System:
YES
Wellness System:
YES
Training Setup:
CRP, Training zone, Distance, Default profile, Personal Km/h, Personal
min/h, Fitness Test, Weight Loss.
Total number of
program:
Quick-Start, Goal, CPR, Profile 6 +12 customizable, Customer Speed,
Custom Pace, Interval Training, Training Zone, Weight Loss
Submaximal test:
Fitness test
Language available:
Italian, UK English, U.S. English, German, Spanish, French, Dutch,
Portuguese, Japanese, Chinese, Russian, Turkish, Danish

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.4
2.4. MECHANICAL CHARACTERISTICS
MECHANICAL CHARACTERISTICS
Length (mm – in)
2013 mm – 79,3”
Width (mm – in)
800 mm – 31,5”
Height (mm – in)
1465 mm – 57,7”
Weight (Kg – lbs)
170 Kg – 374 lbs
Running surface (Width.) mm - in
510 mm 20,07”
Running surface (depth.) mm - in
1450 mm 57,08”
Max user weight (Kg – lbs)
160 kg – 353lbs
Running surface H from ground
195mm – 7,7”
2.5. DIMENSIONS

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.5
2.6. PACKING DIMENSIONS EUROPE AND OVERSEAS

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.6
2.7. AMBIENT SPECIFICATIONS
Temperature
Operating
from 10° to 25° C
Storage
from -10 to 70° C
Humidity
Operating
from 20% to 90% non-condensing
Storage
from 20% to 90% non-condensing
2.8. CONFORMITY TO REGULATIONS
EUROPE
USA
EMI regulations
EN61000-6-1 (2007)
EN61000-6-3 (2007)
EN61000-3-2 (2007)
EN61000-3-3 (2009)
-
Electrical safety
regulations
EN 60335-1 (2008) UL 1647
FCC 15
Mechanical safety
regulations
EN957-1 (2006)
EN957-6 (2003) -
Directives
2006/42/CE
2004/108/CE
2006/95/CE
-
Moreover:
Electrical isolation class: Class I;
Protection rating: IP20.

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.7
2.9. WIRING DIAGRAMS
2.9.1. VISIOWEB AND ALE MET-CE (220VAC)
ALE Driver
ALE Boa rd
Micro
UP/ DOW N Motor
UP/ DOW N
Motor
Power Supply Box
Boa rd
Power Supply
On/Off
Sw itch
J3A
TRM54
LED
J2
J7
J8 J5
CU317
J1
CU325
CU343
GND
Circui t Bra cker
Filter
Circui t Bra cker
Main Switch
Poewr Entry
Module
CU315
WR233
CU343
Pach.
Conn. 1
W6185
Lower casing
Connectors board
AV IN
JACK
AUDIO OUT
Antenna
inlet
RJ45
C.N.
RJ45
CU389
Ferrite
(WR786)
DISPLAY
LCD
CPU Board
Inverter
CN1
Headphone
JACK
J5
TOUCH
SCREEN
CN27
Digital TUNER Boa rd
WIRELESS
Boa rd
Antenna
MAIN (B)
Antenna
AUX (A)
J1 J2
J9
CN2
CN3
J12
FS
SConnector Boardi
C-SAFE
CN6
CN19
CN4
CN17
Emerg . HW
Emerg . S W
CN22
Cardio
Receiver
HS/ HR
INFERIOR
Sens or
(Right)
INFERIOR
Sens or
(Left)
UPPER
Sens or
(Left)
UPPER
Sens or
(Right)
CU323
UP/ DOW N
JOYS T I CK
(Right)
SP EED
JOYSTICK
(Left)
CN31
CN29
CN24
CU321
USB
CBQ-32
CU132
Dua l
TGS
Reader USB
CN14
iP OD DOCKING
STATION
CU167
CN26
Capacitive
Touch
Screen
control
Board
CN11
J13
CU390
CU342
CU308
Flat
CU336
CU391
CU340
LEFT
Upright
CU350
WB657
CU344
CU403
HD4
HD1
HD 3 & 2
CU342
CU337
CU381
CU341
LAN
Power
&
Serial
CU320
C.N. C.N. C.N.
C.N.
C.N.
C.N.
C.N.
C.N.
C.N.
Patch Conn. 2
F
F
CU322
CU392
CU316
CU319
RIGHT
Upright
CAPTION:
C.N. = Connection
F
= Ferrite
GND
= Ground

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.8
2.9.2. VISIOWEB AND ALE MET-UT (110VAC)
Lower casing
Connectors board
AV IN
JACK
AUDIO OUT
Antenna
inlet
RJ45
C.N.
RJ45
CU389
ALE MET Driver
ALE MET Board
Microswitch
UP/ DOW N
UP/ DOW N
Motor
Power Supply
BOX
Scheda Filtro
Power Supply
On/Off
Sw itch
Ferrite
(WR786)
J3A
TRM54
LED
J2
J7
J8 J5
J1
DISPLAY
LCD
CPU Board
Inverter
CN1
Headphone
JACK
J5
TOUCH
SCREEN
CN27
Digita l TUNER Board
WIRELESS
Boa rd
Antenna
MAIN (B)
Antenna
AUX (A)
J1 J2
J9
CN2
CN3
J12
FS
SConnector Boardi
C-SAFE
CN6
CN19
CN4 CN17
Emerg. HW
Emerg. S W
CN22
Cardio
Receiver
HS/ HR
INFERIOR
Sensor
(Right)
INFERIOR
Sensor
(Left)
UPPER
Sensor
(Left)
UPPER
Sensor
(Right)
CU323
UP/ DOW N
JOYST I CK
(Right)
SPEED
JOYSTICK
(Left)
CN31
CN29
CN24
CU321
USB
CBQ-32
CU132
Dua l
TGS
Reader USB
CN14
iP OD DOCKING
STATION
CU167
CN26
Capacitive
Touch
Screen
control
Board
CN11
J13
CU390CU342
CU319
CU308
Flat
CU336
CU391
CU340
RIGHT
Upright LEFT
Upright
GND
Circuit Bra cke r
Filtro
Circuit Bra cke r
Main Switch
Power Entry
Module
CU315
CU350
WB657
CU344
CU403
HD4
HD1
HD 3 & 2
CU342
CU337
CU317
Patch
Conn. 1
AUTOTRANSFORMER
F
Belt
Motor
W6185
F
CU381
CU143
CU143
CU343
WR233
CU341
LAN
Power
&
Serial
CU320
CU316
CU325
C.N.
C.N. C.N. C.N.
C.N.
C.N.C.N.
C.N.
C.N.
C.N.
Patch Conn. 2
F
F
CU322
CU392
CAPTION:
C.N. = Connection
F
= Ferrite
GND
= Ground

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.9
2.10. CABLES
The colour of the cables can be changed, refer in particular to the Pin Out.
2.10.1. CBQ CABLES
CBQ32: TGS cable
(Patch conn.– CPU Board)
CPU Board
CN19
Signal Colour Patch conn.
1
+12 Vdc power supply
Red
8
3
Rx
Brown
1
5
Tx
Blue
2
9
Gnd
Black
6
2.10.2. WB CABLES
WB657: Flat Tuner Board cable
(CPU Board –TUNER Board)
CPU Board
J9
Signal
TUNER Board
J13
1
Capacitive Signal
flat
…50
Capacitive Signal
flat
2.10.3. AUTOTRANSFORMERCABLE
AUTOTRANSFORMER cable
(Autotransformer –ON/OFF Switch –ALE Driver)
Autotransformer Signal
ON/OFF
Switch
ALE
Driver
Cable internally
connected
(PHASE) 110Vac Power Supply
1
(NEUTRAL) 110Vac Power Supply
2
(PHASE) 220Vac Power Supply
1
(NEUTRAL) 220Vac Power Supply
2

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page 2.10
2.10.4. CU CABLES
CU132: TGS signal cable
(Patch conn. –TGS Dual reader)
Patch conn. Signal Colour
TGS Dual reader
CN1
8
+12Vdc power supply
Black
2
1
RX
Green
1
2
TX
Black
4
6
GND
Black
5
CU167: iPod signal cable
(CPU Board– Docking Station)
Scheda CPU
CN26
Signal Colore Docking Station
1
+V bus USB
Black
14
2
GND bus USB
Black
13
3
TX - RX
Black
11
4
RX – TX
Black
12
5
CTS
Black
10
6
+5Vdc
Black
9
7
GND
Black
8
8
GND
Black
7
9
Video Gnd
Black
6
10
Video signal
Black
5
11
Audio L Gnd
Black
4
12
Audio L signal
Black
3
13
Audio R signal
Black
2
14
Audio R Gnd
Black
1
CU308: User USB port cable
(CPU Board –USB Port)
CPU Board
CN14
Signal Colour USB Port
1
+5v
Red
1
2
USB-
White
2
3
USB+
Black
3
4
GND
Green
4
5
Shield
Blue
5