TOORX POWER MAG User manual

Ed : Rev : Cod :
INSTRUCTION
08/19 TOXPRFTRXPOMAG00

1
PREPARATION BEFORE USE
.
1.Fix 12# to the hole of M6 below
the handrail elbow,then fix 52# to
12#,plug 53# connecting wire.
2. Put 57# through 58#,56#,and
fix it to the bracket.
3. Gear 8 stages macro adjustment
knob,8 is the biggest resistance,1 is the
lightest resistance,choose proper
adjusting stage according to your own
exercise request.
4.Properly choose to adjust incline
according to your own exercise
request

2
Belt Middle Placement and Tightness Adjustment
It is very necessary to adjust the belt to the best condition for the better use of the treadmill and the
treadmill can work better.
Belt Middle Placement
1.Put the motorized treadmill on the level ground.
2.If the running belt deviate to the right, turn the right side adjusting bolt clockwise by 1/2 circle, then
turn the left side adjusting bolt anticlockwise by 1/2 circle. Picture A
3.If the running belt deviate to the left, turn the left adjusting bolt clockwise by 1/2 circle,then turn the
right side adjusting bolt anticlockwise by 1/2 circle.Picture B.
After long time use,Gear 8 positions
micro adjusting knob line may be
prolonged,User can fine-tune the
adjusting screw properly,So the gear 8
positions micro adjusting knob can
adjust resistance better.
Picture B.Adjust running belt to right
Picture A. Adjust running belt to left

3
NO.
ITEM
DESCRIPTION
Q’TY
NO.
ITEM
DESCRIPTION
Q’TY
01
Main frame
1
02
base frame
1
03
Handrail elbow
1
04
Connecting tube
seat
1
05
Rear roller cover
2
06
bolt pinch plate
1
07
sleeve
∮16*∮12*40L
2
08
small sleeve
∮15*9.5
4
09
Front roller
cover
2
10
Front axis
sleeve
2
11
Supporting
adjusting
bracket
1
12
Meter assembly
plate
1
13
Front roller
1
14
Rear roller
1
15
Three-in-one
bolt
1
16
Gear 8 positions
micro adjusting
knob
1
17
Cylinder
1
18
Nylon sleeve
2
19
Cushion
6
20
plastic cement
side rail
2
21
Running board
1
22
Running belt
1
23
transporting
wheel
2
24
Round outer
tube topple
2
25
transporting
wheel stopple
2
26
Buffer feet
cushion
4
27
wire plug
3
28
Left cover
1
29
Right cover
1
30
Magnetic box
1
31
screw
M8*70
2
32
screw
M8*40
2
33
screw
M8*55
2
34
screw
M8*10
2
35
screw
M8*70
2
36
screw
M6*25
6
37
screw
M8*30
2
38
screw
M8*15
4
39
screw
M6*15
8
40
screw
M5*30
2
41
screw
M6*20
2
42
screw
M12*55
2
43
Washer
∮8.5*∮16*t1.5
14
44
washer
∮6.5*∮12*t1.5
16
45
Nut
M6
6
46
Nut
M8
4
47
Screw
M6*25
2
48
screw
M4*15
2
49
Screw
M10*30
2
50
washer
∮10.5*∮
20*t2.0
6
51
Nut
M10
2
52
Meter
1

4
53
Telephony
connecting wire
1
54
Sensor wire seat
1
55
Ball head steel
bead pin
∮28*∮10*26
2
56
Bottle holder
1
57
Screw
M5
2
58
M5 washer
2
59
Screw
M4
4
60
M4 washer
4

EXERCISE COMPUTER INSTRUCTION MANUAL
■FUNCTIONAL BUTTONS:
1.MODE
①Select the window to be set.
②Reset: hold for 3 seconds to reset all data.
2.UP/RECOVERY
①Increase the blinking number, hold for quick increase.
②Press it to enter/exit pulse recovery function when heat rate display
(IF HAVE PULSE FUNCTION)
3.DOWN
Decrease the blinking number , hold for quick decrease
4.RESET
①During SET, reset the value of the relevant display window.
②Hold for 3 seconds to reset all data .
■FUNCTION
②Exercise time can be set, MAX 99 minutes, each press add or minus 1 minute, countdown to zero, the TIME will flash and beep for 10
seconds.
①Count the cumulative distance from the exercise start to the end, KM means metric, MI means imperial.
②Exercise distance can be set, MAX 99 KM/MI, each press add or minus 0.1, countdownto zero, the DIST will flash and beep for
10 seconds.
②The calorie value can be set, MAX 999, each press add or minus 1, countdown to zero, the CAL will flash and beep for 10 seconds.
1.SPEED : Window A displays
The current exercise speed during exercise.
2.TIME: Window B displays
①Count the cumulative time from the exercise start to the end, and it will
automatically stop timing if without exercise signal over 6 seconds.
3.DISTANCE: Window C displays
4.CALORIES: WindowD displays
①Count the cumulative calories consumed from exercise start to the end.
5.PULSE: Window E displays (IF HAVE)
①Show your current heart rate during exercise, pulse range: 40～240BPM
②The traget pulse value can be set ,range 40-240 BPM .each press add or minus 1.Beep one time every 10 seconds when the
Value over the target heart rate
6.AUTO OFF
Without any exercise signal or operation over 4 minutes, the computer will turn off automatically and memorize the current data.
■INSTALLATION
1.Take off the computer back’s battery cover, put 2pcs 1.5V AAA battery inside correctly.
2.Fix the computer on the front place of exercise machine by screw.
3.Install the magnet and speed sensor on the related place of the exercise machine. Make sure the distance less than 10mm between the
magnet and sensor.
4.Connect the speed signal cable plug and the computer back’s signal plug. If with the hand pulse, connect the hand pulse cable plug
and the computer back’s pulse signal plug.
5.Start exercise, and if the speed value changes, means the installation is correct. Or else check the installation of magnet and sensor,
and also the plug connections between sensor and computer.
■OPERATION
1.RESET
In any displays, hold MODE or RESET button for 3 seconds to reset all the data.
2.SET THE TARGET PARAMETERS
When stop exercise , press MODE to choose the window to be set or reset, the corresponding window’s digit flash, press RESET to
clear the value, and press UP or DOWN to set the flashing window’s value. Hold the button to quick increase or decrease.
Set the value as:TIME→DIST→CAL→PULSE.
3.PULSE RECOVERY (IF HAVE)
Wear the transmitter belt properly, or hold the hand pulse place, the computer will display your current heart rate.
When the pulse window has the display, stop exercise, press RECOVERY to enter the function of pulse recovery. The display will show 1
minute countdown as well as your pulse rate, test your pulse until it counts down to zero. Then it will pop up your pulse recovery level
from F1 to F6, that is, from the fastest recovery to the slowest. The fastest recovery F1 shows the best, F6 means the slowest.
Press RECOVERY again to exit the pulse recovery function.
■REPLACE BATTERY
When the display color fades, or with flash when operate buttons, means the battery has no enough power. Take off the battery cover,
and use 2pcs new 1.5V AAA UM-4 battery to replace the old battery.
A
B
C
D
E
DO WN
C
U
O
P
V
/
E
RE RY
A
B
C
D
E
DOWN
UP/
TENSION
TIME
/500M
BMI
PULSE
SPEED
RPM
STOP
DIS.
BMR
RPM
CAL.
TEMP.
WATT
C
F
%
COUNT
KMPH
RE SET
MO DE
TENSION
TIME
/500M
BMI
PULSE
SPEED
RPM
STOP
DIS.
BMR
RPM
CAL.
TEMP.
WATT
C
F
%
COUNT
KMPH

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
[email protected]
www.toorxprofessional.it