Toro 07027 User manual

FormNo.3406-359RevA
HoseReelMountingKit
Workman®GTXSeriesUtilityVehicle
ModelNo.07027
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Safety
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential
danger.Replaceanydecalthatisdamagedorlost.
133-7202
1.Attention—readtheOperator’sManual;donotcarrymore
than45kg(100lb).
133-4641
1.Warning—donotcarryanypassengers.
©2016—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3406-359*A

Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
Hose-reelmount1
Tubemount1
Hex-headscrew(1/2x2-1/4inches)1
Locknut(1/2inch)1
Clevispin(1/2x2inches)1
2
Hairpincotter1
Installthehose-reelmount.
Thehose-reelmountisdesignedtotaftermarkethosereelswithmountingpatternsofeither40x23cm(15-3/4x9
inches)or39x25cm(15-7/16x10inches).
Tororecommendsthefollowingaftermarkethosereels:
•Reelcraft—CA33112L
•Cox—1125-5-100
Important:Thetotalloadcapacitywhenthiskitisinstalledis45kg(100lb).Wheninstallingthehosereel,verify
thatthehoselength,whenfullofwater,doesnotexceed45kg(100lb),ordamagemayoccur.
Important:Afterinstallingthehose-reelmounttothemachine,thelengthofthefrontorrearofthemachine
extends,makingitmorelikelytohitotherobjects.
Ensurethatthereisalwaysadequateclearancewhenoperatingthemachinewiththehose-reelmountinstalled.
WARNING
Liftingthehose-reelmountwiththehosereelinstalledalonemayresultininjury.
Whenliftingthehose-reelmountwiththehosereelinstalled,ensurethatyouhave2peopletoinstallit
tothemachine.
1
PreparingtheMachine
NoPartsRequired
Procedure
Parkthemachineonalevelsurface,settheparkingbrake,shutofftheengine,andremovethekey.
2

2
InstallingtheHose-ReelMount
Partsneededforthisprocedure:
1Hose-reelmount
1Tubemount
1Hex-headscrew(1/2x2-1/4inches)
1Locknut(1/2inch)
1Clevispin(1/2x2inches)
1Hairpincotter
InstallingtheHose-ReelMounttothe
FrontoftheMachine
ForMachineswiththeFrontHitchKitwithaBrush
GuardInstalled
1.Insertthetubemountintothehose-reelmountuntil
theholesinthetubemountalignwiththefarthest
holesinthehose-reelmount(Figure1).
Figure1
1.Locknut(1/2inch)3.Hose-reelmount
2.Hex-headscrew(1/2x
2-1/4inches)
4.Tubemount
2.Securethetubemounttothehose-reelmountwiththe
hex-headscrew(1/2x2-1/4inches)andthelocknut
(1/2inch)asshowninFigure1.
3.Loosenthe‘T’handleonthefronthitchattachment
(Figure2).
Figure2
1.Tubemount3.‘T’handle
2.Fronthitchattachment4.Clevispin(1/2x2inches)
andhairpincotter
4.Insertthetubemountintothefronthitchattachment
andsecureitwiththeclevispin(1/2x2inches)and
hairpincotter(Figure2).
5.Tightenthe‘T’handleonthefronthitchattachment
(Figure2).
InstallingtheHose-ReelMounttothe
FrontoftheMachine
ForMachineswiththeFrontHitchKitwithouta
BrushGuardInstalled
1.Insertthetubemountintothehose-reelmountuntil
theholesinthetubemountalignwiththefarthest
holesinthehose-reelmount(Figure1).
2.Securethetubemounttothehose-reelmountwiththe
hex-headscrew(1/2x2-1/4inches)andthelocknut
(1/2inch)asshowninFigure1.
3.Loosenthe‘T’handleonthefronthitchattachment
(Figure3).
Figure3
1.Tubemount3.‘T’handle
2.Fronthitchattachment4.Clevispin(1/2x2inches)
andhairpincotter
3

4.Insertthetubemountintothefronthitchattachment
andsecureitwiththeclevispin(1/2x2inches)and
hairpincotter(Figure3).
5.Tightenthe‘T’handleonthefronthitchattachment
(Figure3).
InstallingtheHose-ReelMounttothe
RearoftheMachine
1.Insertthetubemountintothehose-reelmountuntil
theholesinthetubemountalignwiththefrontholes
inthehose-reelmount(Figure4).
Figure4
1.Locknut(1/2inch)3.Hex-headscrew(1/2x
2-1/4inches)
2.Hose-reelmount4.Tubemount
2.Securethetubemounttothehose-reelmountwiththe
hex-headscrew(1/2x2-1/4inches)andthelocknut
(1/2inch)asshowninFigure4.
3.Loosenthe‘T’handleonthecargobedreceiver(Figure
5).
Figure5
1.Tubemount3.Clevispin(1/2x2inches)
andhairpincotter
2.Cargobedreceiver4.‘T’handle
4.Insertthetubemountintothecargobedreceiverand
secureitwiththeclevispin(1/2x2inches)andhairpin
cotter(Figure5).
5.Tightenthe‘T’handleonthecargobedreceiver
(Figure5).
4