Toro 23172 User manual

FormNo.3413-793RevB
StumpGrinderFit-UpKit
TX1000CompactToolCarrier
ModelNo.23172
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia
tocausecancer,birthdefects,orreproductiveharm.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
Rightshieldbracket1
Leftshieldbracket1
Bolt(1/4x3/4inch)4
2Locknut(1/4inch)4
Installtheshieldbrackets.
Shieldsupport2
Shield1
Bolt(1/4x1-1/2inch)8
Washer8
3
Locknut(1/4inch)8
Assembletheoperatorshield.
4Quick-attachassembly1Replacethequick-attachassembly.
©2017—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3413-793*B

1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Engagetheparkingbrake.
3.Lowertheloaderarms.
4.Shutofftheengineandremovethekey.
g036689
Figure1
2
InstallingtheShield
Brackets
Partsneededforthisprocedure:
1Rightshieldbracket
1Leftshieldbracket
4Bolt(1/4x3/4inch)
4Locknut(1/4inch)
Procedure
1.Measureinfromtheedgesoftheframeas
illustratedinFigure2andmarkthelocations
oftheholesformountingtheshieldbracketon
bothsidesofthemachine.
Note:Iftheholesexist,skiptostep3.
g213269
Figure2
1.7.0cm(2-3/4inches)4.Holes
2.5.7cm(2-1/4inches)5.Referencebar
3.1.3cm(1/2inch)
2

2.Drillahole(9/32inch)throughtheframeateach
markedlocation.
3.Installtheleftshieldbracketontheleftframe
using2bolts(1/4x3/4inch)and2locknuts(1/4
inch)asshowninFigure3.
g202825
Figure3
1.Bolts(1/4x3/4inch)3.Locknut(1/4inch)
2.Leftshieldbracket
4.Installtherightshieldbracketontherightframe
using2bolts(1/4x3/4inch)and2locknuts(1/4
inch),similartoFigure3.
3
AssemblingtheOperator
Shield
Partsneededforthisprocedure:
2Shieldsupport
1Shield
8Bolt(1/4x1-1/2inch)
8Washer
8Locknut(1/4inch)
Procedure
1.Assembletheshieldandexibleskirttothe
shieldsupports,asillustratedinFigure4,using
8bolts(1/4x1-1/2inch),8washers,and8
locknuts(1/4inch).
g202842
Figure4
1.Locknut(8)5.Skirt
2.Washer(8)6.Shieldsupport(2)
3.Shield7.Shieldbracket(2)
4.Bolt(8)
2.Slidetheshieldsupportsintothepocketsinthe
shieldbracketsonthetractionunit(Figure4).
Note:Theskirtshoulddrapeovertheengine
orhood.
3

4
ReplacingtheQuick-Attach
Assembly
Partsneededforthisprocedure:
1Quick-attachassembly
Procedure
1.Laythestumpgrinderatontheoor.
2.Placewoodblocksunderthebodyofthestump
grindersothatthequick-attachplateisoffthe
oor.
3.Removethelargebolt(1x2-1/4inch),washer,
nut(1inch),2smallbolts(1/2x1-1/2inches),
and2nuts(1/2inch)securingthequick-attach
assemblytothestumpgrinder(Figure5).
Removetheassembly.
g206389
Figure5
1.Largebolt(1x2-1/4inch),
washer,andnut(1inch)
3.Quick-attachassembly
2.Smallbolt(1/2x1-1/2
inches)andnut(1/2inch)
4.Installthenewquick-attachassemblytothe
stumpgrinderusingthehardwareyouremoved,
asshowninFigure5.
Note:Thenewquick-attachassemblyhasa
widerhoseloop.
5.Torquethelargebolt(1x2-1/4inch)to406N∙m
(300ft-lb),andtorquethesmallbolts(1/2x
1-1/2inches)to101N∙m(75ft-lb).
6.Routethehosesthroughthehoseloop(Figure
6).
g208071
Figure6
1.Hoseloop2.Hoses
4