URBAN OUTFITTERS HUXLEY BOOKSHELF User manual

HUXLEY BOOKSHELF
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN
OUTFITTERS,
© 2017 UO, Inc. All rights
reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution
or
prosecuted.
eat
floors.
rea.
D E
Hex Key
x1
Bolt
[1/4” x 1- 3/4”] x20
I J
1x 2x
HUXLEY BOOKSHELF
OUTFITTERS,
INC.
reserved, including all applicable copyright, design and patent
or
other infringement will be
unt
on unev
PARTS INCLUDED
F G
x
Bolt
[1/4” x 1- 1/4”] x6
Flat Washer 1/4”
K
Screw
[3 x 32mm] x2
Page 1 of 4
H
Spring Washer
[1/4"] x26
Flat Washer
[1/4”] x26
L
Screw
[3 x 19mm] x2
TOOLS REQUIRED BUT NOT INCLUDED:
PHILLIPS HEAD SCREW DRIVER
Do not throw away packing materials and carton until assembly complete.
Assemble all parts on a clean smooth surface.
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place over hheat or Air conditioning vents.
Adjust levelers so that the furniture sits flat on uneveenn floors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden aarea.
You may need to re-tighten all bolts after initial use.
TIP KIT

HUXLEY BOOKSHELF
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN
OUTFITTERS,
© 2017 UO, Inc. All rights
reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution
or
prosecuted.
STEP 1
With help lay the P
arts out onto a clean smooth surface such as carpet or cardboard.
with Shelves (B) as shown. I
nsert Flat Washer (
t Overtighten
STEP 2
Locate the holes in the bottom of L
eg
ng clockwise. Do Not Overtighten
HUXLEY BOOKSHELF
OUTFITTERS,
INC.
reserved, including all applicable copyright, design and patent
or
other infringement will be
arts out onto a clean smooth surface such as carpet or cardboard.
Align the
nsert Flat Washer (
en with suppli
) by turning clockwise. Do
Do not over-tighten.
eg
s (A).
Insert Flat Washer (H
), Spring washer (
) by t
Tighten with supplied Hex Key (D). Do not over-tighten .
Page 2 of 4
Align the
Legs (A)
Ti
H), Spring washer (G), and Bolt (F). Tighten with Hex Key (D).
), Spring washer (
G), and Bolt (E).

HUXLEY BOOKSHELF
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN
OUTFITTERS,
© 2017 UO, Inc. All rights
reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution
or
prosecuted.
ce.
kwise.
aking sure you do not lean It on the legs as this can damage them
ven flooring.
HUXLEY BOOKSHELF
OUTFITTERS,
INC.
reserved, including all applicable copyright, design and patent
or
other infringement will be
helves (C). Press firmly into
rm
STEP 3
Align Shelves (C) as shown and press fi ly into pllace. Insert Flat Washer (H), Spring Washer (G), and
Bolt (E).
) by turning cl
Tighten with supplied Hex Key (D). Do not over-tighten .
Upright an damage them
You will need to adjust the levelers for
You will need to adjust the levelers for uneven flooring.
Page 3 of 4
Upright making sure you do not lean It on the legs as thi
STEP 4
With help stand the Bookshelf upright making sure you do not lean it on its side. This can cause damage to the
legs.

HUXLEY BOOKSHELF
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN
OUTFITTERS,
© 2017 UO, Inc. All rights
reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution
or
prosecuted.
from
izontally to the top back edge of the furniture. Insert the short screws
d tighten securely using screwdriver. Please contact your local
chor for your wall type
be placed and mark location on the wall for the other mounting
ced approximately 2” below the bracket mounted to the furniture
tically to the wall by inserting the long screws provided through the
ecurely using screwdriver. Please contact your local hardware store to
l type
n the back edge are in line with the brackets on the wall
trap down through each bracket. Bring both ends together and slide the
ceiving end of the strap until snu
urely laced and locked to the bracket
HUXLEY BOOKSHELF
OUTFITTERS,
INC.
reserved, including all applicable copyright, design and patent
or
other infringement will be
To prevent injury and property dama
Attached the mounting bracket h nsert the short screws
through the holes in the bracket a tact your local
get the correct
Determine where the furniture is other mounting
bracket crew holes. It should be ed to the furniture
mounting bracket v rovided through the
hole in the bracket and tightenin local hardware store to
get the correct anchor for your w
the wall
Lace an end of the nylon restrain s together and slide the
thin end of the strap through the
Check to make sure the strap is s
Page 4 of 4
Attached the mounting bracket horizontally to the top back edge of the furniture.
through the holes in the bracket and tighten securely using screwdriver. Please c
Determine where the furniture is to be placed and mark location on the wall for t
bracket crew holes. It should be placed approximately 2” below the bracket mou
mounting bracket vertically to the wall by inserting the long screws
hole in the bracket and tightening securely using screwdriver. Please contact you
on the back edge are in line with the brackets o
Lace an end of the nylon restraint strap down through each bracket. Bring both e
STEP 5
Align the Anti Tip Brackets (B) to the Top bbaack of the Case.
Insert Screws (C) and tighten completely. Doo not overtighten.
STEP 6
Contact your local hardware store to purchassee the correct anchors for your
Align the brackets to the wall and make sure tthey line up
Screw the brackets to the wall using the correecct anchors.
Slide the case to the wall. Leaving a little bit oof room between the case and the wall.
Feed the Nylon Strap through both brackets aannd pull tight.
wall-type.
with the brackets on the back of the cassee from step 1.